Evaluation of Glove Performance after Decontamination.

Studies of healthcare providers doffing personal protective equipment, especially gloves, indicate that self-contamination does occur. Although generally this is not hazardous, working with particularly pathogenic organisms, such as Ebola virus and Clostridium difficile, can present a serious health risk. Decontaminating medical gloves before removal can reduce self-contamination and mitigate the spread of these types of pathogens. Also, in cases of extreme shortage, the Centers for Disease Control and Prevention (CDC) has specific recommendations for decontaminating gloves for extended use. Reuse of medical gloves is strongly discouraged by both the CDC and Food and Drug Administration. This work seeks to lay a foundation of testing to evaluate whether a decontamination method is compatible for a given glove type and material. Four potential methods of decontamination (commercial hand soap, alcohol-based hand sanitizer, commercial bleach, and quaternary ammonium solution) were tested on a variety of surgical and patient examination gloves. The method of barrier performance evaluation was ASTM D5151-19, Standard Test Method for Detection of Holes in Medical Gloves. Our results indicated that the performance of the gloves after treatment was highly dependent on the composition of the medical gloves. In general, the surgical gloves in this study performed better than the patient examination gloves, regardless of the material from which they were made. Specifically, vinyl examination gloves tended to have poorer performance. In this study, the number of gloves available to test were limited and therefore statistical significance is beyond the scope of this project.

Use of Transmission Electron Microscopy for Analysis of Aerosol Particles and Strategies for Imaging Fragile Particles.

For over 25 years, transmission electron microscopy (TEM) has provided a method for the study of aerosol particles with sizes from below the optical diffraction limit to several microns, resolving the particles as well as smaller features. The wide use of this technique to study aerosol particles has contributed important insights about environmental aerosol particle samples and model atmospheric systems. TEM produces an image that is a 2D projection of aerosol particles that have been impacted onto grids and, through associated techniques and spectroscopies, can contribute additional information such as the determination of elemental composition, crystal structure, and 3D particle structures. Soot, mineral dust, and organic/inorganic particles have all been analyzed using TEM and spectroscopic techniques. TEM, however, has limitations that are important to understand when interpreting data including the ability of the electron beam to damage and thereby change the structure and shape of particles, especially in the case of particles composed of organic compounds and salts. In this paper, we concentrate on the breadth of studies that have used TEM as the primary analysis technique. Another focus is on common issues with TEM and cryogenic-TEM. Insights for new users on best practices for fragile particles, that is, particles that are easily susceptible to damage from the electron beam, with this technique are discussed. Tips for readers on interpreting and evaluating the quality and accuracy of TEM data in the literature are also provided and explained.

Ultrafine Particles Emitted through Routine Operation of a Hairdryer.

Particulate matter is a large concern for human health. Fine and ultrafine particulate matter has been shown to negatively impact human health; for example, it causes cardiopulmonary diseases. Current regulation targets the size of the particles, but composition also impacts toxicity. Indoor sources of air pollution pose unique challenges for human health due to the potential for human exposure to high concentrations in confined spaces. In this work, six hairdryers were each operated within a plexiglass chamber, and their emissions were analyzed with transmission electron microscopy and energy-dispersive spectroscopy. All hairdryers were found to emit ultrafine iron, carbon, and copper. In addition, emissions from two hairdryers primarily contained silver nanoparticles in the ultrafine range (<100 nm). The ultrafine particle emission rates for the hairdryers that did not contain silver were measured and found to be lower than ultrafine particle emissions by gas stoves and electric burners. Based on their size, these particles can either remain in the lung or enter the bloodstream after inhalation and potentially cause long-term health effects.

Size-Dependent Liquid-Liquid Phase Separation in Atmospherically Relevant Complex Systems.

Physical properties of aerosol particles, such as liquid-liquid phase separation (LLPS), have the potential to impact the climate system. Model systems have been shown to have size-dependent LLPS in the submicron regime; however, these systems are an extreme simplification of ambient aerosol, which can include myriad organic compounds. We expand the studies of LLPS in particles consisting of ammonium sulfate and more complex organic mixtures from multiple organic compounds to α-pinene secondary organic matter (SOM). All systems display a size-dependent morphology, with small particles remaining homogeneous while large particles phase-separate. Surprisingly, three-phase particles were also observed in some of the systems in addition to a new phase state that we have termed channel morphology, which can arise upon efflorescence. The existence of size-dependent LLPS in complex organic mixtures and SOM provides evidence that this is a relevant phenomenon for ambient aerosol and should be considered when modeling atmospheric aerosol.

Heterogeneous Freezing of Carbon Nanotubes: A Model System for Pore Condensation and Freezing in the Atmosphere.

Heterogeneous ice nucleation is an important mechanism for cloud formation in the upper troposphere. Recently, pores on atmospheric particles have been proposed to play a significant role in ice nucleation. To understand how ice nucleation occurs in idealized pores, we characterized the immersion freezing activity of various sizes of carbon nanotubes. Carbon nanotubes are used both as a model for pores and proxy for soot particles. We determined that carbon nanotubes with inner diameters between 2 and 3 nm exhibit the highest ice nucleation activity. Implications for the freezing behavior of porous materials and nucleation on soot particles will be discussed.