Synthetic oligomer analysis using atmospheric pressure photoionization mass spectrometry at different photon energies.

Atmospheric pressure photoionization (APPI) followed by mass spectrometric detection was used to ionize a variety of polymers: polyethylene glycol, polymethyl methacrylate, polystyrene, and polysiloxane. In most cases, whatever the polymer or the solvent used (dichloromethane, tetrahydrofuran, hexane, acetone or toluene), only negative ion mode produced intact ions such as chlorinated adducts, with no or few fragmentations, in contrast to the positive ion mode that frequently led to important in-source fragmentations. In addition, it was shown that optimal detection of polymer distributions require a fine tuning of other source parameters such as temperature and ion transfer voltage. Series of mass spectra were recorded in the negative mode, in various solvents (dichloromethane, tetrahydrofuran, hexane, toluene, and acetone), by varying the photon energy from 8eV up to 10.6eV using synchrotron radiation. To these solvents, addition of a classical APPI dopant (toluene or acetone) was not necessary. Courtesy of the synchrotron radiation, it was demonstrated that the photon energy required for an efficient ionization of the polymer was correlated to the ionization energy of the solvent. As commercial APPI sources typically use krypton lamps with energy fixed at 10eV and 10.6eV, the study of the ionization of polymers over a wavelength range allowed to confirm and refine the previously proposed ionization mechanisms. Moreover, the APPI source can efficiently be used as an interface between size exclusion chromatography or reverse phase liquid chromatography and MS for the study of synthetic oligomers. However, the photoionization at fixed wavelength of polymer standards with different molecular weights showed that it was difficult to obtain intact ionized oligomers with molecular weights above a few thousands.

Identification of synthetic dyes in early colour photographs using capillary electrophoresis and electrospray ionisation-mass spectrometry.

Capillary electrophoresis with photodiode array detection (CE-PDA) and with electrospray ionisation-mass spectrometry (CE-ESI-MS) was used for the separation and the identification of 23 synthetic organic dyes, among those used in early 20th century colour photographs such as autochromes. Both cationic and anionic dyes could be separated within 15min using a single CE-PDA method. The method was used as the basis to develop a CE-ESI-MS methodology through the optimisation of the relevant ESI and MS parameters. Sheath liquid composition, nebulising gas pressure, drying gas flow rate and drying gas temperature were found to influence the sensitivity of the detection. These parameters were optimised in positive and negative ion modes for cationic dyes and anionic dyes, respectively. The two analyses could be carried out successively on a single sample. In view of the application to cultural heritage objects, the CE-ESI-MS analytical procedure was applied to identify the dyes in a Filmcolor artefact, late version of the autochrome. The results complemented and enhanced current knowledge as four cationic dyes and three anionic dyes were identified. Four additional dyes are proposed as possibly present as traces.

Characterization by mass spectrometry of an unknown polysiloxane sample used under uncontrolled medical conditions for cosmetic surgery.

For a complete understanding of the raw material used for cosmetic surgery under uncontrolled medical conditions, an unknown sample of polydimethylsiloxanes has been investigated utilizing a combination of analytical techniques: pyrolysis/gas chromatography/mass spectrometry (Py/GC/MS), electrospray ionization (ESI)-MS, matrix-assisted laser desorption/ionization time-of-flight (MALDI-TOF)MS, and liquid chromatography (LC)/MS. Among these techniques, the LC/APCI-MS coupling allowed the fastest and more effective analysis. In addition, the complexity of the mass spectra deduced from these LC/MS experiments was simplified compared to the mass spectra obtained by MALDI-TOF. In this work, we have demonstrated how the LC/APCI-MS coupling applied to polydimethylsiloxane samples permits the full characterization of samples where end groups of different nature can be present in very small quantities.

APCI interface for LC- and SEC-MS analysis of synthetic polymers: advantages and limits.

The main advantage of the APCI interface for the LC-MS analysis of synthetic polymers resides in its compatibility with the main chromatographic modes: reversed-phase liquid chromatography, normal-phase liquid chromatography, and size exclusion chromatography in organic phase, with the usual flow rates. Moreover, APCI can be used in positive or negative modes. Representative applications are described to highlight benefits and limitations of the LC-APCI-MS technique with the analysis of industrial polymers up to molecular masses of 5 kDa: polyethers; polysiloxanes; and copolymers of siloxanes. Results are discussed in regard to those obtained by more classical techniques: SEC and MALDI-MS. The use of an APCI interface in LC-MS and SEC-MS coupling applied to synthetic polymers is efficient up to 2000-4500 Da. The main drawback of the APCI interface is the in-source decomposition that is observed above m/z = 2000-3000 and can induce an underestimation of average molecular weights. However, APCI allows detection on a wide range of polarity of sample/solvent and appears to be complementary to ESI.

Block lengths and block sequence of linear triblock and glycerol derivative diblock copolyethers by electrospray ionization--collision-induced dissociation mass spectrometry.

Chemical properties of ethylene oxide (EO) and propylene oxide (PO) block copolymers are strongly dependent on their sequence. Useful information about copolymer sequence can be obtained by tandem mass spectrometry (MS/MS). In this work, collision-induced dissociation (CID) of ammonium adducts of various linear triblock and glycerol derivative diblock copolyethers produced by electrospray ionization was studied under low-energy conditions. At first, homopolymers MS/MS spectra enabled us to identify the nature of the product ions and to suggest decomposition pathways. Then, it was shown that copolyethers with the same composition in each repeat unit but with inversed block sequences (i.e., PEO-b-PPO-b-PEO vs PPO-b-PEO-b-PPO and gPEO-b-PPO vs gPPO-b-PEO) can be easily distinguished with characteristic fragment ions. In the case of linear copolymers, CID spectra gave pertinent information about block lengths.

Analysis of poly(oxyethylene) and poly(oxypropylene) triblock copolymers by MALDI-TOF mass spectrometry.

Triblock copolymers of ethylene oxide (EO) and propylene oxide (PO) are widely used in the chemical industry as nonionic surfactants. Triblock copolymers can be arranged in a EO-PO-EO or PO-EO-PO sequence. This arrangement results in an amphiphilic copolymer, in which the block sequence and block length determine the properties of the copolymer. MALDI-TOF MS was used to analyze various triblock copolyethers: EO-PO-EO (Mn =2000 g.mol(-1)), PO-EO-PO (Mn = 2000 g.mol(-1)), and a random copolymer EO/PO (Mn = 2500 g.mol(-1)). Data treatment was assisted by using a homemade software allowing a picture of monomer composition of oligomers from the mass spectra. MALDI-TOF mass spectra of EO/PO copolymers were shown to depend strongly on the number of laser shots, relative proportions of polymer/salt, and the nature of the matrix. An unsaturated byproduct was detected. Its presence was demonstrated by prefractionation of copolymers by SEC before MALDI-TOF analysis, and its content was estimated by 1H NMR. The formation of layers inside the MALDI deposit was evidenced by varying the number of laser shots. Lighter oligomers of the copolymer, unsaturated byproduct, or both would be in the core of the deposit, coated with heavier oligomer. The layer formation depends on the nature of the matrix and the quantity of added salt. DHB matrix with a relative high sodium salt content induces layer formation inside the deposit, whereas dithranol matrix or low salt content does not. Consequently, an optimization of experimental parameters in order to estimate the lighter oligomers or unsaturated byproduct content or to obtain the actual representation of the monomer contribution in the copolymers from the MS data only seems obviously critical. MALDI-TOF mass spectrometry is obviously a powerful technique to analyze copolymers, but a careful survey of the experimental parameters is required. The combination of MALDI-TOF MS with separations techniques and NMR brings precious complementary information.

Characterization of peptides by liquid chromatography/electrospray ionization mass spectrometry using silver nitrate as a post-column complexant.

Two model peptides, des-Arg1-bradykinin (DAB) and bradykinin (B), were cationized by Ag+ after their separation by reversed-phase liquid chromatography (RPLC) prior to mass spectrometry (MS). Silver nitrate solution was used as a post-column reagent. The RPLC and MS experimental conditions were optimized using flow injection in order to obtain sufficiently abundant silver adducts to permit MS/MS experiments. The use of water-methanol with 0.1% formic acid as mobile phase allowed a good chromatographic separation of the two peptides with a polymeric stationary phase and sufficiently abundant silver-containing adducts, [M + Ag + H]2+ and [M + 2Ag]2+. The gas-phase dissociation of [DAB + Ag + H]2+ and [DAB + 2Ag]2+ led to interpretable mass spectra during the on-line cationization experiment. Most of the ions obtained by dissociating [DAB + Ag + H]2+ and [DAB + 2Ag]2+ species are silver-containing ions but the ions produced depend on the parent. The ions coming from the dissociation of the doubly charged silver adducts [DAB + Ag + H]2+ or [DAB + 2Ag]2+ are of interest compared with those coming from the singly charged silver species or doubly charged protonated species. The fragmentation of the doubly charged silver adducts provides ions over the entire mass range. Although the presence of several prolines in des-Arg1-bradykinin prevents the formation of some expected ions, the observation of triplets [an-H + Ag]+, [bn-H + Ag]+ and [bn + OH + Ag]+ produced by the dissociation of on-line Ag(+)-cationized peptides could contribute to greater success of automatic sequencing of peptides.