Performance evaluation and energy potential analysis of anaerobic membrane bioreactor (AnMBR) in the treatment of simulated milk wastewater.

An anaerobic membrane bioreactor (AnMBR) was employed as primary treatment unit for anaerobic treatment of simulated wastewater to produce high effluent quality. A lab scale hollow fiber membrane was used to scrutinize the performance of AnMBR as a potential treatment system for simulated milk wastewater and analyze its energy recovery potential. The 15 L bioreactor was operated continuously at mesophilic conditions (35 °C) with a pH constant of 7.0. The membrane flux was in the range of 9.6-12.6 L/m2. h. The different organic loading rates (OLRs) of 1.61, 3.28, 5.01, and 8.38 g-COD/L/d, of simulated milk wastewater, were fed to the reactor and the biogas production rate was analyzed, respectively. The results revealed that the COD removal efficiencies of 99.54 ± 0.001% were achieved at the OLR of 5.01 gCOD/L/d. The highest methane yield was found to be at OLR of 1.61 gCOD/L/d at HRT of 30 d with the value of 0.33 ± 0.01 L-CH4/gCOD. Moreover, based on the analysis of energy balance in the AnMBR system, it was found that energy is positive at all the given HRTs. The net energy production (NEP) ranged from 2.594 to 3.268 kJ/gCOD, with a maximum NEP value of 3.268 kJ/gCOD at HRT 10 d HRT. Bioenergy recovery with the maximum energy ratio, of 4.237, was achieved with an HRT of 5 d. The study suggests a sizable energy saving with the anaerobic membrane process.

Fourth generation biofuel from genetically modified algal biomass for bioeconomic development.

Biofuels from microalgae have promising potential for a sustainable bioeconomy. Algal strains' oil content and biomass yield are the most influential cost drivers in the fourth generation biofuel (FGB) production. Genetic modification is the key to improving oil accumulation and biomass yield, consequently developing the bioeconomy. This paper discusses current practices, new insights, and emerging trends in genetic modification and their bioeconomic impact on FGB production. It was demonstrated that enhancing the oil and biomass yield could significantly improve the probability of economic success and the net present value of the FGB production process. The techno-economic and socioeconomic burden of using genetically modified (GM) strains and the preventive control strategies on the bioeconomy of FGB production is reviewed. It is shown that the fully lined open raceway pond could cost up to 25% more than unlined ponds. The cost of a plastic hoop air-supported greenhouse covering cultivation ponds is estimated to be US 60,000$ /ha. The competitiveness and profitability of large-scale cultivation of GM biomass are significantly locked to techno-economic and socioeconomic drivers. Nonetheless, it necessitates further research and careful long-term follow-up studies to understand the mechanism that affects these parameters the most.

The performance of simultaneous partial nitritation, anammox, denitrification, and COD oxidation (SNADCO) method in the treatment of digested effluent of fish processing wastewater.

The simultaneous partial nitritation, anammox, denitrification, and COD oxidation (SNADCO) method was successfully carried out in an air-lift moving bed biofilm reactor (AL-MBBR) with cylinders carriers for the treatment of digested fish processing wastewater (FPW). Synthetic wastewater was used as substrate at stage 1. It changed into the digested FPW with dilution variation in order to increase the nitrogen and COD loading rates. With influent concentration of NH4+-N of 909 ± 101 mg-N/L and COD of 731 ± 26 mg/L, the nitrogen removal efficiency was 86.8% (nitrogen loading rate of 1.21 g-TN/L/d) and the COD removal efficiency was 50.5% (COD loading rate at 0.98 g-COD/L/d). This study showed that the process has the advantages in treating the real high ammonia concentration of digested wastewater containing organic compounds. The nitritation and anammox route was predominant in nitrogen removal, while COD oxidation and microbe proliferation played the main role in COD removal.

Effect of Cellulose Nanocrystals Extracted from Oil Palm Empty Fruit Bunch as Green Admixture for Mortar.

This paper aims to examine the effect of cellulose nanocrystals (CNCs) derived from oil palm empty fruit bunch fiber (EFB) incorporating cement mortar on its structural performances. Cellulose nanocrystals (CNCs) were extracted from α-cellulose extracted from EFB using an acid hydrolysis process with a concentration of acid used was 64% w/v under the temperature of 45 °C for 60 minutes. The Cellulose nanocrystals (CNCs) were mixed into the cement mortar ranging from 0 to 0.8% w/w and its mechanical properties were determined. The developed CNCs mortar was characterized for their compressive and flexural properties as well as microstructure. The influence of CNCs concentration, curing method, dispersion of CNCs on mortar's mechanical performance was thoroughly examined to find out the optimum condition. Overall results revealed that an addition of 0.4% cellulose nanocrystals has shown to increase the compressive and flexural strength to 46% and 20%, respectively cured under the wrapping method. The hydration of cementitious composites also improved significantly with the addition of CNCs by the formation of highly crystalline of portlandite observed under the XRD test. This present work demonstrates the importance of palm oil empty fruit bunch waste as a sustainable resource of cellulose nanocrystals admixture to achieve structural strength of cement mortar and promotes green technologies in construction.

Statistical optimization of titanium recovery from drinking water treatment residue using response surface methodology.

Water treatment plants generate vast amounts of sludge and its disposal is one of the most expensive and environmentally problematic challenges worldwide. As sludge from water treatment plants contains a considerable amount of titanium, both can create serious environmental concerns. In this study, the potential to recover titanium from drinking water treatment residue was explored through acid leaching technique. Statistical design for the optimization of titanium recovery was proposed using response surface methodology (RSM) based on a five-level central composite design (CCD). Three independent variables were investigated, namely the acid concentration (3 M-7 M), temperature (40 °C - 80 °C) and solid/liquid ratio (0.005-0.02 g/mL). According to the analysis of variance (ANOVA), the p-value (<0.0001) indicated the designed model was highly significant. Optimization using RSM gave the best fit between validated and predicted data as elucidated by the coefficient of determination with R2 values of 0.9965. However, acid concentration and solid/liquid ratio showed an initial increase in titanium recovery followed by recovery reduction with increasing concentration and ratio. Quadratic RSM predicted the maximum recovery of titanium to be 67.73% at optimal conditions of 5.5 M acid concentration, at a temperature of 62 °C with a solid/liquid ratio of 0.01 g/mL. The verification experiments gave an average of 66.23% recovery of titanium, thus indicating that the successfully developed model to predict the response. This process development has significant importance to reduce the cost of waste disposal, environmental protection, and recovery of economically valuable products.

Optimization of aluminium recovery from water treatment sludge using Response Surface Methodology.

For decades, water treatment plants in Malaysia have widely employed aluminium-based coagulant for the removal of colloidal particles in surface water. This generates huge amount of by-product, known as sludge that is either reused for land applications or disposed to landfills. As sludge contains high concentration of aluminium, both can pose severe environmental issues. Therefore, this study explored the potential to recover aluminium from water treatment sludge using acid leaching process. The evaluation of aluminium recovery efficiency was conducted in two phases. The first phase used the one factor at a time (OFAT) approach to study the effects of acid concentration, solid to liquid ratio, temperature and heating time. Meanwhile, second phase emphasized on the optimization of aluminium recovery using Response Surface Methodology (RSM). OFAT results indicated that aluminium recovery increased with the rising temperature and heating time. Acid concentration and solid to liquid ratio, however, showed an initial increment followed by reduction of recovery with increasing concentration and ratio. Due to the solidification of sludge when acid concentration exceeded 4 M, this variable was fixed in the optimization study. RSM predicted that aluminium recovery can achieve 70.3% at optimal values of 4 M, 20.9%, 90 °C and 4.4 h of acid concentration, solid to liquid ratio, temperature and heating time, respectively. Experimental validation demonstrated a recovery of 68.8 ±â€¯0.3%. The small discrepancy of 2.2 ±â€¯0.4% between predicted and validated recovery suggests that RSM was a suitable tool in optimizing aluminium recovery conditions for water treatment sludge.

Plant-driven removal of heavy metals from soil: uptake, translocation, tolerance mechanism, challenges, and future perspectives.

Increasing heavy metal (HM) concentrations in the soil have become a significant problem in the modern industrialized world due to several anthropogenic activities. Heavy metals (HMs) are non-biodegradable and have long biological half lives; thus, once entered in food chain, their concentrations keep on increasing through biomagnification. The increased concentrations of heavy metals ultimately pose threat on human life also. The one captivating solution for this problem is to use green plants for HM removal from soil and render it harmless and reusable. Although this green technology called phytoremediation has many advantages over conventional methods of HM removal from soils, there are also many challenges that need to be addressed before making this technique practically feasible and useful on a large scale. In this review, we discuss the mechanisms of HM uptake, transport, and plant tolerance mechanisms to cope with increased HM concentrations. This review article also comprehensively discusses the advantages, major challenges, and future perspectives of phytoremediation of heavy metals from the soil.

Removal Rate of Organic Matter Using Natural Cellulose via Adsorption Isotherm and Kinetic Studies.

In this study, the removal of natural organic matter (NOM) using coconut fiber (CF) and palm oil fiber (POF) was investigated. Preliminary analysis was performed using a jar test for the selection of optimal medium before the fabricated column model experiment. The equilibrium studies on isotherms and kinetic models for NOM adsorption were analyzed using linearized correlation coefficient. Results showed that the equilibrium data were fitted to Langmuir isotherm model for both CF and POF. The most suitable adsorption model was the pseudo-first-order kinetic model for POF and pseudo-second-order kinetic model for CF. The adsorption capacities achieved by the CF and POF were 15.67 and 30.8 mg/g respectively. Based on this investigation, it can be concluded that the POF is the most suitable material for the removal of NOM in semi polluted river water.

The efficient role of aquatic plant (water hyacinth) in treating domestic wastewater in continuous system.

In this study, water hyacinth (Eichhornia crassipes) was used to treat domestic wastewater. Ten organic and inorganic parameters were monitored in three weeks for water purification. The six chemical, biological and physical parameters included Dissolved Oxygen (DO), Biological Oxygen Demand (BOD), Chemical Oxygen Demand (COD), Ammoniacal Nitrogen (NH3-N), Total Suspended Solids (TSS), and pH were compared with the Interim National Water Quality Standards, Malaysia River classification (INWQS) and Water Quality Index (WQI). Between 38% to 96% of reduction was observed and water quality has been improved from class III and IV to class II. Analyses for Electricity Conductivity (EC), Salinity, Total Dissolved Solids (TDS) and Ammonium (NH4) were also investigated. In all parameters, removal efficiency was in range of 13-17th day (optimum 14th day) which was higher than 3 weeks except DO. It reveals the optimum growth rate of water hyacinth has great effect on waste water purification efficiency in continuous system and nutrient removal was successfully achieved.

A study on large scale cultivation of Microcystis aeruginosa under open raceway pond at semi-continuous mode for biodiesel production.

The study explores on upstream and downstream process in Microcystis aeruginosa for biodiesel production. The alga was isolated from temple tank, acclimatized and successfully mass cultivated in open raceway pond at semi-continuous mode. A two step combined process was designed and harvested 99.3% of biomass, the daily dry biomass productivity was recorded up to 28gm(-2)day(-1). The lipid extraction was optimized and achieved 21.3%; physicochemical properties were characterized and found 11.7% of FFA, iodine value 72% and 99.2% of ester content. The lipid was transesterified by a two step simultaneous process and produced 90.1% of biodiesel; the calorific value of the biodiesel was 38.8MJ/kg. Further, the physicochemical properties of biodiesel was characterized and found to be within the limits of American ASTM D6751. Based on the areal and volumetric biomass productivity estimation, M. aeruginosa can yield 84.1 tons of dry biomass ha(-1)year(-1).

Development of Bio-PORec® system for polyhydroxyalkanoates (PHA) production and its storage in mixed cultures of palm oil mill effluent (POME).

High PHA production and storage using palm oil mill effluent (POME) was investigated using a laboratory batch Bio-PORec® system under aerobic-feeding conditions. Results showed that maximum PHA was obtained at a specific rate (q(p)) of 0.343 C-mol/C-molh when air was supplied at 20 ml/min. The PHA yield was found to be 0.80 C-mol/C-mol acetic acid (HAc) at microaerophilic condition and the mass balance calculation showed that PHA production increased up to 15.68±2.15 C-mmol/cycle. The experiments showed that short feeding rate, limited requirements for electron acceptors (e.g. O(2), NO(3)) and nutrients (N and P) showed lower tendency of glycogen accumulation and contributed more to PHA productivity.