Hydroxyapatite nano-pillars on TI-6Al-4V: Enhancements in cell spreading and proliferation during cell/surface integration.

Despite the attractive combinations of cell/surface interactions, biocompatibility, and good mechanical properties of Ti-6Al-4V, there is still a need to enhance the early stages of cell/surface integration that are associated with the implantation of biomedical devices into the human body. This paper presents a novel, easy and reproducible method of nanoscale and nanostructured hydroxyapatite (HA) coatings on Ti-6Al-4V. The resulting nanoscale coatings/nanostructures are characterized using a combination of Raman spectroscopy, scanning electron microscopy equipped with energy dispersive x-ray spectroscopy. The nanostructured/nanoscale coatings are shown to enhance the early stages of cell spreading and integration of bone cells (hFOB cells) on Ti-6Al-4V surfaces. The improvements include the acceleration of extra-cellular matrix, cell spreading and proliferation by nanoscale HA structures on the coated surfaces. The implications of the results are discussed for the development of HA nanostructures for the improved osseointegration of Ti-6Al-4V in orthopedic and dental applications.

Datasets on the elastic and mechanical properties of hydroxyapatite: A first principle investigation, experiments, and pedagogical perspective.

The purpose of this data article is to report the quantum mechanical analysis by generalized gradient approximation (GGA) exchange-correlation functional using density functional theory (DFT). The predictions were based on the elastic constants and mechanical properties of stoichiometric hydroxyapatite (HAp) crystal. The elastic stiffness constants in hexagonal symmetry were obtained by fitting the Hookes' law for the energy-strain and stress-stain relations. Some of the theoretical datasets were compared to measured mechanical properties of produced HAp pellets obtained through micro and nanoindentation experiments. The datasets show considerable anisotropy in the stress-strain behaviour and are discussed in the context of the mechanical properties of HAp which are useful for tissue engineering. We also provide a pedagogical snapshot on the use of the datasets herein to teach and interpret DFT based atomistic simulations in a typical blended online teaching set-up for engineering students using a new pedagogy, CACPLA (Communicate, Active, Collaborate, Practice, Learning and Assessment).

Teaching bioengineering using a blended online teaching and learning strategy: a new pedagogy for adapting classrooms in developing countries.

Research and academia have been recently affected by the Coronavirus (COVID-19), and physical classrooms and laboratory experiments have been affected significantly due to the recent laboratory closures. This has led to innovative approaches to curb this problem. To address these difficulties in teaching bioengineering related courses that is of significant interest to students of the Faculty of Engineering in Ahmadu Bello University, Zaria, Nigeria, and of course, useful for engineering-based higher education institutions (HEI), a transitional pedagogy: Communicate, Active, Collaborate, Problem-based Solving, Learning and Assessment (CACPLA), which encompasses blended learning, was developed as a new teaching and learning strategy. In this study, we show that this new strategy can initiate a steady transition from physical classrooms to full online instruction for some subjects in engineering. This method has been trialled as an exercise for a module as part of an envisioned biomedical engineering degree programme which can be integrated with local industries and research institutions in sub-Saharan Africa. The teaching materials and environment were carefully designed and 253 students of third and final year classes participated as the experimental group. Also, the effect of critical thinking, pre-lecture, and post lecture on the overall performance of the students was assessed. Two questionnaires were designed for data collection, (a) for technical questions, (b) for receptiveness. The result of a student survey suggests favourable reception of the teaching methodology, which aided their understanding of the general bioengineering concept as applied to the materials chemistry and mechanical measurements context. It was noticed that 80% of the students indicated that the blended learning method was sufficient in achieving the learning outcomes of the study. The method is envisioned as a useful and sustainable complement to traditional teaching pedagogies and workshops due to the convenience and relatively high accessibility to Zoom and Google Meet Apps which can be readily employed without incurring significant costs.

Silver-Polymethylhydrosiloxane-Quaternary Ammonium Coating on Anodized Aluminum with Excellent Antibacterial Property.

Multidrug-resistant bacteria are known to survive on high-touch surfaces for days, weeks, and months, contributing to the rise in nosocomial infections. Inducing antibacterial property in such surfaces can presumably reduce the overall microbial burden and subsequent nosocomial infections in hygiene critical environments. In the present study, a one-pot sol-gel process has been deployed to incorporate silver (Ag) and quaternary ammonium salt (QUAT) bactericides in a polymethylhydrosiloxane (PMHS) matrix. The Ag-PMHS-QUAT nanocomposite was coated on anodized aluminum (AAO/Al) by a simple ultrasound-assisted deposition process. The morphological features and chemical composition of the Ag-PMHS-QUAT nanocomposite have been characterized using SEM, XRD spectroscopy, and attenuated total reflection-Fourier transform infrared spectroscopy (ATR-FTIR) to confirm the formation of Ag-QUAT nanocomposites within the polymeric network of PMHS. The Ag-PMHS-QUAT nanocomposite coating on anodized aluminum oxide (AAO/Al) coupon exhibited superior antibacterial property with a 6-log bacterial reduction compared to the 5-log reduction for the commercially available antimicrobial copper coupon.

Surface Functionalized MXenes for Wastewater Treatment-A Comprehensive Review.

Over 80% of wastewater worldwide is released into the environment without proper treatment. Whilst environmental pollution continues to intensify due to the increase in the number of polluting industries, conventional techniques employed to clean the environment are poorly effective and are expensive. MXenes are a new class of 2D materials that have received a lot of attention for an extensive range of applications due to their tuneable interlayer spacing and tailorable surface chemistry. Several MXene-based nanomaterials with remarkable properties have been proposed, synthesized, and used in environmental remediation applications. In this work, a comprehensive review of the state-of-the-art research progress on the promising potential of surface functionalized MXenes as photocatalysts, adsorbents, and membranes for wastewater treatment is presented. The sources, composition, and effects of wastewater on human health and the environment are displayed. Furthermore, the synthesis, surface functionalization, and characterization techniques of merit used in the study of MXenes are discussed, detailing the effects of a range of factors (e.g., PH, temperature, precursor, etc.) on the synthesis, surface functionalization, and performance of the resulting MXenes. Finally, the limits of MXenes and MXene-based materials as well as their potential future research directions, especially for wastewater treatment applications are highlighted.

Snail Based Carbonated-Hydroxyapatite Material as Adsorbents for Water Iron (II).

Carbonated hydroxyapatite (CHAp) adsorbent material was prepared from Achatina achatina snail shells and phosphate-containing solution using a wet chemical deposition method. The CHAp adsorbent material was investigated to adsorb aqua Fe(II) complex; [Fe(H2O)6]2+ from simulated iron contaminated water for potential iron remediation application. The CHAp was characterized before and after adsorption using infrared (IR) and Raman spectroscopy. The IR and the Raman data revealed that the carbonate functional groups of the CHAp adsorbent material through asymmetric orientation in water bonded strongly to the aqua Fe(II) complex adsorbate. The adsorption behaviour of the adsorbate onto the CHAp adsorbent correlated well to pseudo-second-order kinetics model, non-linear Langmuir and Freundlich model at room temperature of a concentration (20-100 mg L-1) and contact time of 180 min. The Langmuir model estimated the maximum adsorption capacity to be 45.87 mg g-1 whereas Freundlich model indicated an S-type isotherm curvature which supported the spectroscopy revelation.

Comparative Study of Phosgene Gas Sensing Using Carbon and Boron Nitride Nanomaterials-A DFT Approach.

Phosgene (COCl2), a valuable industrial compound, maybe a public safety and health risk due to potential abuse and possible accidental spillage. Conventional techniques suffer from issues related to procedural complexity and sensitivity. Therefore, there is a need for the development of simple and highly sensitive techniques that overcome these challenges. Recent advances in nanomaterials science offer the opportunity for the development of such techniques by exploiting the unique properties of these nanostructures. In this study, we investigated the potential of six types of nanomaterials: three carbon-based ([5,0] CNT, C60, C70) and three boron nitride-based (BNNT, BN60, BN70) for the detection of COCl2. The local density approximation (LDA) approach of the density functional theory (DFT) was used to estimate the adsorption characteristics and conductivities of these materials. The results show that the COCl2 molecule adsorbed spontaneously on the Fullerene or nanocages and endothermically on the pristine zigzag nanotubes. Using the magnitude of the bandgap modulation, the order of suitability of the different nanomaterials was established as follows: PBN60 (0.19%) < PC70 (1.39%) < PC60 (1.77%) < PBNNT (27.64%) < PCNT (65.29%) < PBN70 (134.12%). Since the desired criterion for the design of an electronic device is increased conductivity after adsorption due to the resulting low power consumption, PC60 was found to be most suitable because of its power consumption as it had the largest decrease of 1.77% of the bandgap.

A simple sensing of hazardous photo-induced superoxide anion radicals using a molecular probe in ZnO-Nanoparticles aqueous medium.

The generation of reactive oxygen species (ROS) during the photolysis of sunscreens and sun blockers poses consumer safety concerns while necessitating proper identification and quantitation of ROS species. Here, a colorimetric sensing approach has been developed based on a molecular probe (2,3-bis-(2-methoxy-4-nitro-5-sulfophenyl)-2-H-tetrazolium-5-carboxanilide (XTT) tetrazolium salt) to quantitatively measure the photo-induced superoxide anion radicals (O2.) generated from the photocatalysis of zinc oxide nanoparticles (ZnO-NPs) in aqueous solutions. Note that superoxide anion radicals are assumed to be the main reactive oxygen species (ROS) generated from such photocatalysis. The characterisation of ZnO-NPs before and after irradiation showed average particle sizes of 616.5 and 295.3 nm and ζ-potential values of 0 and -24.4 mV, respectively. It is hoped that this proposed protocol can be further developed to efficiently detect other ROS present in inorganic sun blockers and to optimize the utility of various sunscreen formulations.

The effect of titanium dioxide synthesis technique and its photocatalytic degradation of organic dye pollutants.

Nanostructured mesoporous titanium dioxide (TiO2) particles with high specific surface area and average crystallite domain sizes within 2 nm and 30 nm have been prepared via the sol-gel and hydrothermal procedures. The characteristics of produced nanoparticles have been tested using X-Ray Diffraction (XRD), Brunauer-Emmett-Teller (BET) surface area analysis, Scanning Electron Microscopy (SEM), Fourier Transform Infra-Red (FTIR), and Raman Spectroscopy as a function of temperature for their microstructural, porosity, morphological, structural and absorption properties. The as-synthesized TiO2 nanostructures were attempted as catalysts in Rhodamine B and Sudan III dyes' photocatalytic decomposition in a batch reactor with the assistance of Ultra Violet (UV) light. The results show that for catalysts calcined at 300 °C, ∼100 % decomposition of Sudan III dye was observed when Hydrothermal based catalyst was used whiles ∼94 % decomposition of Rhodamine B dye was observed using the sol-gel based catalysts. These synthesized TiO2 nanoparticles have promising potential applications in the light aided decomposition of a wide range of dye pollutants.

Modified halloysite nanoclay as a vehicle for sustained drug delivery.

This paper presents the effect of modified halloysite nanotubes on the sustained drug release mechanisms of sodium salicylate. Acid treatment and composite polymer-halloysite modification techniques were adopted in this study. After each modification, sodium salicylate drug was loaded, and in vitro release properties were evaluated and compared with the raw unmodified halloysite nanotubes. The results obtained from SEM, TEM and FTIR analyses indicate that both acid treatment and composite formation have no effect on the tubular structure and morphology of halloysite. However, modification of the halloysite nanotubes did influence the drug release rate. In the acid treatment modification, there was an improved loading of sodium salicylate drug which resulted in the sustain release of large amount of the sodium salicylate. In the polymer/halloysite composite formation, a consistent layer of polymer was formed around the halloysite during the composite formation and thus delayed release providing sustained release of sodium salicylate drug over a longer period of time as compared to the acid treated and unmodified halloysite. The results from the invitro release were best fitted with the Higuchi and the Koresymer-Peppas models.

H2O2 rejuvenation-mediated synthesis of stable mixed-morphology Ag3PO4 photocatalysts.

Ag3PO4 photocatalyst has attracted interest of the scientific community in recent times due to its reported high efficiency for water oxidation and dye degradation. However, Ag3PO4 photo-corrodes if electron accepter such as AgNO3 is not used as scavenger. Synthesis of efficient Ag3PO4 followed by a simple protocol for regeneration of the photocatalyst is therefore a prerequisite for practical application. Herein, we present a facile method for the synthesis of a highly efficient Ag3PO4, whose photocatalytic efficiency was demonstrated using 3 different organic dyes: Methylene Blue (MB), Methyl orange (MO) and Rhodamine B (RhB) organic dyes for degradation tests. Approximately, 19 % of Ag3PO4 is converted to Ag0 after 4.30 hours of continuous UV-Vis irradiation in presence of MB organic dye. We have shown that the Ag/Ag3PO4 composite can be rejuvenated by a simple chemical oxidation step after several cycles of photocatalysis tests. At an optimal pH of 6.5, a mixture of cubic, rhombic dodecahedron, nanosphere and nanocrystals morphologies of the photocatalyst was formed. H2O2 served as the chemical oxidant to re-insert the surface metallic Ag into the Ag3PO4 photocatalyst but also as the agent that can control morphology of the regenerated as-prepared photocatalyst without the need for any other morphology controlling Agent (MCA). Surprisingly, the as- regenerated Ag3PO4 was found to have higher photocatalytic reactivity than the freshly made material and superior at least 17 times in comparison with the conventional Degussa TiO2, and some of TiO2 composites tested in this work.