Force and number of myosin motors during muscle shortening and the coupling with the release of the ATP hydrolysis products.

KEY POINTS: Muscle contraction is due to cyclical ATP-driven working strokes in the myosin motors while attached to the actin filament. Each working stroke is accompanied by the release of the hydrolysis products, orthophosphate and ADP. The rate of myosin-actin interactions increases with the increase in shortening velocity. We used fast half-sarcomere mechanics on skinned muscle fibres to determine the relation between shortening velocity and the number and strain of myosin motors and the effect of orthophosphate concentration. A model simulation of the myosin-actin reaction explains the results assuming that orthophosphate and then ADP are released with rates that increase as the motor progresses through the working stroke. The ADP release rate further increases by one order of magnitude with the rise of negative strain in the final motor conformation. These results provide the molecular explanation of the relation between the rate of energy liberation and shortening velocity during muscle contraction. The chemo-mechanical cycle of the myosin II--actin reaction in situ has been investigated in Ca(2+)-activated skinned fibres from rabbit psoas, by determining the number and strain (s) of myosin motors interacting during steady shortening at different velocities (V) and the effect of raising inorganic phosphate (Pi) concentration. It was found that in control conditions (no added Pi ), shortening at V ≤ 350 nm s(-1) per half-sarcomere, corresponding to force (T) greater than half the isometric force (T0 ), decreases the number of myosin motors in proportion to the reduction of T, so that s remains practically constant and similar to the T0 value independent of V. At higher V the number of motors decreases less than in proportion to T, so that s progressively decreases. Raising Pi concentration by 10 mM, which reduces T0 and the number of motors by 40-50%, does not influence the dependence on V of number and strain. A model simulation of the myosin-actin reaction in which the structural transitions responsible for the myosin working stroke and the release of the hydrolysis products are orthogonal explains the results assuming that Pi and then ADP are released with rates that increase as the motor progresses through the working stroke. The rate of ADP release from the conformation at the end of the working stroke is also strain-sensitive, further increasing by one order of magnitude within a few nanometres of negative strain. These results provide the molecular explanation of the relation between the rate of energy liberation and the load during muscle contraction.

The myofilament elasticity and its effect on kinetics of force generation by the myosin motor.

The half-sarcomere is the functional unit of striated muscle, in which, according to a "linear" mechanical model, myosin motors are parallel force generators with an average strain s acting between the opposing myosin and actin filaments that behave as a series elastic element with compliance Cf. Thus the definition of the mechanism of force generation by myosin motors in muscle requires integration of the crystallographic model of the working stroke with the mechanical constraints provided by the organization of motors in the half-sarcomere. The relation between half-sarcomere compliance and force (Chs-T) during the development of isometric contraction deviates, at low forces, from that predicted by the linear model, indicating the presence of an elastic element in parallel with the myosin motors, which may influence the estimate of s. A working stroke model, kinetically constrained by the early phase of the isotonic velocity transient following a force step, predicts that the rate of quick force recovery following a length step is reduced to the observed value by a Cf of 12.6nm/MPa. With this value of Cf, the fit of Chs-T relation during the isometric force rise gives s=1.8-1.9nm, similar to the values estimated using the linear model.

The working stroke of the myosin II motor in muscle is not tightly coupled to release of orthophosphate from its active site.

Skeletal muscle shortens faster against a lower load. This force-velocity relationship is the fundamental determinant of muscle performance in vivo and is due to ATP-driven working strokes of myosin II motors, during their cyclic interactions with the actin filament in each half-sarcomere. Crystallographic studies suggest that the working stroke is associated with the release of phosphate (Pi) and consists of 70 deg tilting of a light-chain domain that connects the catalytic domain of the myosin motor to the myosin tail and filament. However, the coupling of the working stroke with Pi release is still an unsolved question. Using nanometre-microsecond mechanics on skinned muscle fibres, we impose stepwise drops in force on an otherwise isometric contraction and record the isotonic velocity transient, to measure the mechanical manifestation of the working stroke of myosin motors and the rate of its regeneration in relation to the half-sarcomere load and [Pi]. We show that the rate constant of the working stroke is unaffected by [Pi], while the subsequent transition to steady velocity shortening is accelerated. We propose a new chemo-mechanical model that reproduces the transient and steady state responses by assuming that: (i) the release of Pi from the catalytic site of a myosin motor can occur at any stage of the working stroke, and (ii) a myosin motor, in an intermediate state of the working stroke, can slip to the next actin monomer during filament sliding. This model explains the efficient action of muscle molecular motors working as an ensemble in the half-sarcomere.

PicoNewton-millisecond force steps reveal the transition kinetics and mechanism of the double-stranded DNA elongation.

We study the kinetics of the overstretching transition in λ-phage double-stranded (ds) DNA from the basic conformation (B state) to the 1.7-times longer and partially unwound conformation (S state), using the dual-laser optical tweezers under force-clamp conditions at 25°C. The unprecedented resolution of our piezo servo-system, which can impose millisecond force steps of 0.5-2 pN, reveals the exponential character of the elongation kinetics and allows us to test the two-state nature of the B-S transition mechanism. By analyzing the load-dependence of the rate constant of the elongation, we find that the elementary elongation step is 5.85 nm, indicating a cooperativity of ~25 basepairs. This mechanism increases the free energy for the elementary reaction to ~94 k(B)T, accounting for the stability of the basic conformation of DNA, and explains why ds-DNA can remain in equilibrium as it overstretches.