The effect of the incoming boundary layer thickness on the aeroacoustics of finite wall-mounted square cylinders.

This paper is concerned with the influence of the incoming wall boundary layer thickness on the noise produced by a square finite wall-mounted cylinder in cross-flow. Acoustic and near wake velocity measurements have been taken in an anechoic wind tunnel for a cylinder in two different near-zero-pressure gradient turbulent boundary layers with thicknesses of 130% and 370% of the cylinder width, W. The cylinders have an aspect ratio of 0.29≤L/W≤22.9 (where L is the cylinder span) and were examined at a Reynolds number, based on width, of ReW = 1.4 × 104. The results presented in this paper demonstrate that increasing the height of the boundary layer delays the production of acoustic tones to higher aspect ratios. The height of the boundary layer changes the balance between upwash and downwash across the cylinder span, resulting in a delayed onset of the shedding regimes and correspondingly, the production of acoustic tones.

Surface curvature effects on the tonal noise of a wall-mounted finite airfoil.

This paper is concerned with the influence of camber on the noise of a wall-mounted finite airfoil with natural boundary layer transition. Tonal noise measurements taken in an aeroacoustic wind tunnel are presented for airfoils with aspect ratio of 2, NACAxx12 profile and camber between 0 and 6% at 40% chord. The results show camber is an important parameter that determines the operating conditions for which acoustic tone generation occurs and the number and intensity of the tones produced. Airfoils with 0%-2% camber have an acoustic signature that is dominated by a high amplitude primary tone, whereas the spectra of airfoils with higher camber of 4%-6% feature a more pronounced side tone structure. Tonal noise production does not collapse with lift coefficient, demonstrating that the local flow conditions influence the noise source. Tonal noise production is explained in terms of changes to mean flow topology, namely the location of flow separation, which is linked to tonal noise generation. Scaling of airfoil tonal noise is found to vary with angle of attack and pressure gradient. Empirical scaling laws for the primary tone frequency dependence on velocity are also derived for the cambered airfoils.

Numerical simulation of blade-passage noise.

Numerical simulations are used to investigate the noise generated by the passage of a rotor blade past a fixed object (the blade-passage effects), which was studied by simulating a three-bladed rotor that is supported by a vertical cylindrical tower. To isolate the blade-passage effects, no incoming wind was introduced in the simulation. The symmetric blade was set to zero pitch angle relative to the plane of rotation and two blade-tower distances were investigated. The sliding mesh method was used to simulate the rotation of the blades and Curle's acoustic analogy was used to predict the noise generated from the simulated flow data. Intense force fluctuations occur during the interaction on both the tower and the passing blade, and these are the primary sources of blade-passage noise. The contribution of the force fluctuations on the support tower to blade-passage noise, which previously had been ignored, was revealed to be more significant than that of the blades. The numerical model successfully predicts the noise spectra, which are validated by the very good agreement with experimental measurements. The simulations provide a framework to better understand blade-tower interaction noise in various applications.

Experimental investigation of trailing edge noise from stationary and rotating airfoils.

Trailing edge noise from stationary and rotating NACA 0012 airfoils is characterised and compared with a noise prediction based on the semi-empirical Brooks, Pope, and Marcolini (BPM) model. The NACA 0012 is symmetrical airfoil with no camber and 12% thickness to chord length ratio. Acoustic measurements were conducted in an anechoic wind tunnel using a stationary NACA 0012 airfoil at 0° pitch angle. Airfoil self-noise emissions from rotating NACA 0012 airfoils mounted at 0° and 10° pitch angles on a rotor-rig are studied in an anechoic room. The measurements were carried out using microphone arrays for noise localisation and magnitude estimation using beamforming post-processing. Results show good agreement between peak radiating trailing edge noise emissions of stationary and rotating NACA 0012 airfoils in terms of the Strouhal number. Furthermore, it is shown that noise predictions based on the BPM model considering only two dimensional flow effects, are in good agreement with measurements for rotating airfoils, at these particular conditions.

The effect of acoustic forcing on an airfoil tonal noise mechanism.

The response of the boundary layer over an airfoil with cavity to external acoustic forcing, across a sweep of frequencies, was measured. The boundary layer downstream of the cavity trailing edge was found to respond strongly and selectively at the natural airfoil tonal frequencies. This is considered to be due to enhanced feedback. However, the shear layer upstream of the cavity trailing edge did not respond at these frequencies. These findings confirm that an aeroacoustic feedback loop exists between the airfoil trailing edge and a location near the cavity trailing edge.

Broadband trailing edge noise from a sharp-edged strut.

This paper presents experimental data concerning the flow and noise generated by a sharp-edged flat plate at low-to-moderate Reynolds number (Reynolds number based on chord of 2.0 × 10(5) to 5.0 × 10(5)). The data are used to evaluate a variety of semi-empirical trailing edge noise prediction methods. All were found to under-predict noise at lower frequencies. Examination of the velocity spectra in the near wake reveals that there are energetic velocity fluctuations at low frequency about the trailing edge. A semi-empirical model of the surface pressure spectrum is derived for predicting the trailing edge noise at low-to-moderate Reynolds number.

On the aeroacoustic tonal noise generation mechanism of a sharp-edged plate.

This letter presents an experimental study on the tonal noise generated by a sharp-edged flat plate at low-to-moderate Reynolds number. Flow and far-field noise data reveal that, in this particular case, the tonal noise appears to be governed by vortex shedding processes. Also related to the existence of the tonal noise is a region of separated flow slightly upstream of the trailing edge. Hydrodynamic fluctuations at selected vortex shedding frequencies are strongly amplified by the inflectional mean velocity profile in the separated shear layer. The amplified hydrodynamic fluctuations are diffracted by the trailing edge, producing strong tonal noise.