ABSTRACT
BACKGROUND: This study investigated procedural errors made during root canal preparation with nickel-titanium (NiTi) instruments, using cone beam computed tomography (CBCT) imaging method. MATERIALS AND METHODS: A total of 100 human mandibular molars were divided into five groups (n = 20) according to the NiTi system used for root canal preparation: Group 1 - BioRaCe, Group 2 - K3, Group 3 - ProTaper, Group 4 - Mtwo and Group 5 - Hero Shaper. CBCT images were obtained to detect procedural errors made during root canal preparation. Two examiners evaluated the presence or absence of fractured instruments, perforations, and canal transportations. Chi-square test was used for statistical analyzes. The significance level was set at a=5%. RESULTS: In a total of 300 prepared root canals, 43 (14.33%) procedural errors were detected. Perforation was the procedural errors most commonly observed (58.14%). Most of the procedural errors were observed in the mesiobuccal root canal (48.84%). In the analysis of procedural errors, there was a significant difference (P < 0.05) between the groups of NiTi instruments. The root canals instrumented with BioRaCe had significantly less procedural errors. CONCLUSIONS: CBCT permitted the detection of procedural errors during root canal preparation. The frequency of procedural errors was low when root canals preparation was accomplished with BioRaCe system.
ABSTRACT
The aim of this study was to determine, by Atomic Absorption Spectrometry (AAS), the concentration levels of 11 metals in Type V gray and structural white PC, ProRoot MTA, and MTA Bio. Samples, containing one gram of each tested cement, were prepared and transferred to a 100 mL Teflon tube with a mixture of 7.0 mL of nitric acid and 21 mL of hydrochloric acid. After the reaction, the mixture was filtered and then volumed to 50 mL of distilled water. For each metal, specific patterns were determined from universal standards. Arsenic quantification was performed by hydride generator. The analysis was performed five times and the data were statistically analyzed at 5% level of significance. Only the cadmium presented concentration levels of values lower than the quantification limit of the device. The AAS analysis showed increased levels of calcium, nickel, and zinc in structural white PC. Type V PC presented the greatest concentration levels of arsenic, chromium, copper, iron, lead, and manganese (P < 0.05). Bismuth was found in all cements, and the lowest concentration levels were observed in Portland cements, while the highest were observed in ProRoot MTA. Both PC and MTA-based cements showed evidence of metals inclusion.
Subject(s)
Dental Cements/analysis , Dental Cements/standards , Metals, Heavy/analysis , Dental Cements/chemistry , Metals, Heavy/chemistry , Spectrophotometry, Atomic/methodsABSTRACT
OBJECTIVES: This study evaluated the solubility, dimensional alteration, pH, electrical conductivity, and radiopacity of root perforation sealer materials. MATERIALS AND METHODS: For the pH test, the samples were immersed in distilled water for different periods of time. Then, the samples were retained in plastic recipients, and the electrical conductivity of the solution was measured. The solubility, dimensional alteration, and radiopacity properties were evaluated according to Specification No. 57 of the American National Standards Institute/American Dental Association (ANSI/ADA). Statistical analyses were carried out using analysis of variance (ANOVA) and Tukey's test at a significance level of 5%. When the sample distribution was not normal, a nonparametric ANOVA was performed with a Kruskal-Wallis test (α = 0.05). RESULTS: The results showed that white structural Portland cement (PC) had the highest solubility, while mineral trioxide aggregate (MTA)-based cements, ProRoot MTA (Dentsply-Tulsa Dental) and MTA BIO (Ângelus Ind. Prod.), had the lowest values. MTA BIO showed the lowest dimensional alteration values and white PC presented the highest values. No differences among the tested materials were observed in the the pH and electrical conductivity analyses. Only the MTA-based cements met the ANSI/ADA recommendations regarding radiopacity, overcoming the three steps of the aluminum step wedge. CONCLUSIONS: On the basis of these results, we concluded that the values of solubility and dimensional alteration of the materials were in accordance with the ANSI/ADA specifications. PCs did not fulfill the ANSI/ADA requirements regarding radiopacity. No differences were observed among the materials with respect to the pH and electrical conductivity analyses.
ABSTRACT
Physicochemical properties of pozzolan Portland cement were compared to ProRoot MTA and MTA BIO. To test the pH, the samples were immersed in distilled water for different periods of time. After the pH analysis, the sample was retained in the plastic recipient, and the electrical conductivity of the solution was measured. The solubility and radiopacity properties were evaluated according to specification 57 of the American National Standard Institute/American Dental Association (ANSI/ADA). The statistical analyses were performed using ANOVA and Tukey's test at a 5% level of significance. Pozzolan Portland cement exhibited pH and electrical conductivity mean values similar to those of the MTA-based cements. The solubilities of all tested materials were in accordance with the ANSI/ADA standards. Only the MTA-based cements met the ANSI/ADA recommendations for radiopacity. It might be concluded that the pH and electrical conductivity of pozzolan Portland cement are similar to and comparable to those of MTA-based cements.
