Property Modulation of Graphene Oxide Incorporated with TiO2 for Dye-Sensitized Solar Cells.

Graphene oxide (GO) nano-powder is synthesized by the modified Hummer's method, and further thin films are deposited by using the water solution of GO through spin-coating. These films are thermally reduced along with the synthesized GO nano-powder at 50 to 200 °C in a high vacuum. Microstructural, electrical, and optical properties are expectedly controlled by thermal reduction. The electronic properties of GO are investigated by X-ray photoelectron spectroscopy and near-edge X-ray absorption fine structure. The reduction is confirmed by Raman spectroscopy. The work function and band gap of GO are tuned with the thermal reduction. The changes in properties of GO are not linear, and anomalous changes are observed for the reduction around 150 °C. Pristine and reduced GO nano-powder is incorporated into TiO2 paste to be the photoanode for dye-sensitized solar cells (DSSCs). It is observed that the performance of the fabricated cells is significantly enhanced for the GO reduced at 150 °C, and the cell exhibited a significant increment of ∼23% for the power conversion efficiency in comparison to DSSC based on an unmodified TiO2 photoanode.

Tin Sulfide (SnS) Films Deposited by an Electric Field-Assisted Continuous Spray Pyrolysis Technique with Application as Counter Electrodes in Dye-Sensitized Solar Cells.

The deposition of tin sulfide (SnS) nanostructured films using a continuous spray pyrolysis technique is reported with an electric field present at the nozzle for influencing the atomization and the subsequent film deposition. In the absence of the electric field, the X-ray diffraction pattern shows the orthorhombic phase of SnS with a crystallographic preferred orientation along the (040) plane. The application of the electric field results in significant improvement in the morphology and a reduction in surface roughness (28 nm from 37 nm). The direct optical band gap of the films deposited with and without the electric field is estimated to be 1.5 and 1.7 eV, respectively. The photothermal deflection spectroscopy studies show a lower energetic disorder (no Urbach tail), which indicates an annealing effect in the SnS films deposited under the electric field. The improvement in the film properties is reflected in the expected improvement in the power conversion efficiency (PCE) of dye-sensitized solar cells fabricated using the SnS film as a counter electrode. An enhancement of PCE from 2.07% for the film deposited without the electric field to 2.89% for the film deposited with the electric field shows the role of the electric field in the fabrication of improved SnS films.

Recycling of Perovskite Films: Route toward Cost-Efficient and Environment-Friendly Perovskite Technology.

Mixed organic-inorganic halide perovskite solar cells have reached unprecedentedly high efficiency in a short term. Two major challenges in its large-scale deployment is the material instability and hazardous lead waste. Several studies have identified that lead replacement with its other alternatives does not show the similar assurance. In this manuscript, we introduce the concept of recycling of the degraded perovskite film (PbI2), gaining back the initial optoelectronic properties as the best possible solution to avoid lead waste. The simple recycling procedure allows the utilization of some of the most expensive (fluorine-doped tin oxide), primary energy-consuming (TiO2), and toxic (Pb) parts of the solar cell, reducing the payback time even further. This addresses the major issues of instability and expensive toxic lead disposal, altogether. We have demonstrated the comparative study of feasibility of recycling in degraded perovskite films deposited by three different standard fabrication routes. Films fabricated via acetate route shows efficient recycling compared to the other routes, i.e., chloride and sequential deposition routes. Moreover, recycling in sequentially deposited films needs further optimization.

Unraveling the Effect of Crystal Structure on Degradation of Methylammonium Lead Halide Perovskite.

Despite the remarkable efficiencies of perovskite solar cells, moisture instability has still been the major constraint in the technology deployment. Although, some research groups have discussed the possible mechanisms involved in the perovskite degradation, no broader understanding has been developed so far. Here, we demonstrate that the crystal orientation of perovskite film plays a major role in its degradation. We observed that the films fabricated via different routes led to different degradation behaviors and unraveled that diversity in the degradation rate arises due to the difference in crystallographic characteristics of the films. Using optical and electrical measurements, we show that the film prepared via a single-step (lead chloride precursor based) route undergoes a much faster degradation rate as compared with films prepared using single step (acetate precursor based) and two-step (or sequential deposition) routes. Although the resulting film is methylammonium lead iodide (MAPbI3) regardless of processing via different routes, their respective crystal orientation is different. In this manuscript, we correlate crystal orientation of MAPbI3 with their degradation pattern. Our studies also suggest a possible way to make stable perovskite film.

Enhancement of Y123 dye-sensitized solar cell performance using plasmonic gold nanorods.

The role of the surface plasmon resonance (SPR) of gold nanorods (Au NRs) on the performance of Y123 dye-sensitized solar cells (DSSC) was investigated. DSSCs were fabricated by incorporating different concentrations (0.6 to 3.0 wt%) of Au NRs into TiO2 photoanodes. With an increase in the concentration of the Au NRs, the light absorption by the Y123 dye loaded photoanodes enhanced linearly, but the charge extraction was susceptible to the concentration of the Au NRs. With optimized concentrations (∼1.8 wt%) of the Au NRs, the photocurrent of the DSSC enhanced from 12.45 to 15.74 mA cm-2, and the power conversion efficiency (PCE) improved from 5.31 to 8.86%. The DSSC performance was also verified using Au nanoparticles (the PCE was enhanced from 5.31 to 7.72%) for comparison with the Au NR DSSC performance, which demonstrated the advantage of the Au NRs' shape effect with longitudinal SPR due to the modified light interaction. To explain the experimental observations of the plasmonic DSSC, the Au NRs' extinction efficiency and spatial distribution of the near-fields in complete and porous TiO2 media were also estimated using the finite-element method.

Design and synthesis of N-substituted perylene diimide based low band gap polymers for organic solar cell applications.

In this study, we report on the synthesis and device studies of a series of new copolymers containing N-substituted perylene dimide and dioctylfluorene units as part of the main backbone. A facile synthetic approach avoiding non-selective bromination was used to synthesize the monomer M1 by the reaction of perylene-3,4,9,10-tetracarboxylic dianhydride with 2-amino-7-bromo-9,9-dioctylfluorene. The copolymers P1 and P2 were synthesized by Suzuki polycondensation of M1 with 2,2'-(9,9-dioctyl-9H-fluoren-2,7-diyl)bis(4,4,5,5-tetramethyl-1,3,2-dioxaborolane) M2 and 9-(heptadecan-9-yl)-2,7-bis(4,4,5,5-tetramethyl-1,3,2-dioxaborolan-2-yl)-9H-carbazole M3, respectively. The copolymer P3 was synthesized by direct arylation polymerization of M1 with 4,7-bis(4-octylthiophen-2-yl)benzo[c]-1,2,5-thiadiazole M4. All the copolymers showed thermal stability greater than 380 °C as evidenced from thermogravimetric analysis. The copolymers exhibited a narrow optical band gap (1.80-2.08 eV) with their UV-visible absorption spectra extending up to the NIR region and they are found to be suitable for use in OSC applications. The molecular weights of the polymers P1-P3 were found to be in the range of 10.68 to 16.02 kg mol-1 as measured from GPC analysis. The surface morphology of the active layers based on P1/P2/P3:P3HT blend films was investigated by AFM and the rms values from height images range from 0.65 to 2.90 nm. The polymers were blended with P3HT to fabricate BHJ solar cells in three different weight ratios i.e. 1 : 1, 1.5 : 1 and 2 : 1 and the best power conversion efficiency was observed for the binary film of P3:P3HT blend device in a 1 : 1 weight ratio which reached up to 1.96% with a V oc of 0.55 V, J sc of 10.12 mA cm-2 and FF of 34.63% which is among the highest reported for BHJ solar cells with N-substituted PDI based acceptors.

Role of silver doping on the defects related photoluminescence and antibacterial behaviour of zinc oxide nanoparticles.

The Ag doped ZnO (ZnO:Ag) NPs with a hexagonal wurtzite structure were synthesized by a solution combustion method. X-ray absorption near edge structure (XANES) and X-ray photoelectron spectroscopy (XPS) were used to study the defects, local electronic and atomic structures before and after Ag doping. XPS and XANES studies confirmed the deficiency of concentration of defects in ZnO after Ag doping. The photoluminescence study showed the deep level emission in the orange-red region in addition to the band to band emission. It was also found that the defect related emission of ZnO was decreased with an increasing in Ag concentration. The antibacterial behaviour of ZnO and ZnO:Ag NPs was studied against the gram positive and gram negative bacteria. The role of Ag doping and defects in the ZnO NPs were discussed for the observed antibacterial and photoluminescence behaviour.

Eu3+ doped down shifting TiO2 layer for efficient dye-sensitized solar cells.

Europium doped TiO2 (TiO2:Eu3+) down-shifting (DS) nanophosphors (NPrs) were synthesized by the solution-combustion method with different concentrations of Eu3+. The X-ray diffraction results confirmed the formation of a polycrystalline tetragonal structure of the TiO2. The emission of colour of the TiO2:Eu3+ DS NPr was tuned by varying the doping concentration of Eu3+. The photoluminescence results confirmed that the TiO2:Eu3+ DS NPrs converted the UV light into visible light by energy down-conversion process, i.e. down-shifting of high energy UV photons to low energy visible photons. These TiO2:Eu3+ DS NPrs were used to enhance the efficiency of the Dye sensitized solar cell from 8.32% to 8.80%.

Spray deposited copper zinc tin sulphide (Cu2ZnSnS4) film as a counter electrode in dye sensitized solar cells.

Stoichiometric thin films of Cu2ZnSnS4 (CZTS) were deposited by the spray technique on a FTO coated glass substrate, with post-annealing in a H2S environment to improve the film properties. CZTS films were used as a counter electrode (CE) in Dye-Sensitized Solar Cells (DSCs) with N719 dye and an iodine electrolyte. The DSC of 0.25 cm(2) area using a CE of CZTS film annealed in a H2S environment under AM 1.5G illumination (100 mW cm(-2)) exhibited a short circuit current density (JSC) = 18.63 mA cm(-2), an open circuit voltage (VOC) = 0.65 V and a fill factor (FF) = 0.53, resulting in an overall power conversion efficiency (PCE) = 6.4%. While the DSC using as deposited CZTS film as a CE showed the PCE = 3.7% with JSC = 13.38 mA cm(-2), VOC = 0.57 V and FF = 0.48. Thus, the spray deposited CZTS films can play an important role as a CE in the large area DSC fabrication.

Fabrication of polymer/cadmium sulfide hybrid solar cells [P3HT:CdS and PCPDTBT:CdS] by spray deposition.

This paper investigates fabrication of surfactant free CdS nanoparticles (NPs) and application in the fabrication of P3HT:CdS and PCPDTBT:CdS bulk-heterojunction hybrid solar cells using high-throughput, large-area, low cost spray deposition technique. Both the hybrid active layers and hole transport layers are deposited by spray technique. The CdS/Poly(3-hexylthiophene-2,5-diyl) (P3HT) and CdS/Poly[2,6-(4,4-bis-(2-ethylhexyl)-4H-cyclopenta[2,1-b;3,4-b']dithiophene)-alt-4,7(2,1,3-benzothiadiazole)] (PCPDTBT) hybrid devices are fabricated by spray deposition process at optimized conditions (i.e. film thickness, spray solution volume, distance between sample and spray nozzle, substrate temperature, etc.). The power conversion efficiency of η=0.6% and 1.02% is obtained for P3HT:CdS and PCPDTBT:CdS hybrid devices, respectively. Spray coating holds significant promise as a technique capable of fabricating large-area, high performance hybrid solar cells.

Plasmonic effect of spray-deposited Au nanoparticles on the performance of inverted organic solar cells.

Gold nanoparticles with varying sizes were prepared by the spray process under an electric field (DC voltages of 0 V and 1 kV applied to the nozzle) for studying their role in inverted organic solar cells (ITO/Au/ZnO/P3HT:PCBM/Ag). The application of electric field during the spray process resulted in a smaller size (35 nm as compared to 70 nm without the electric field) of the nanoparticles with more uniform distribution. This gave rise to a difference in the surface plasmon resonance (SPR) effect created by the gold nanoparticles (Au NPs), which then affected the solar cell performance. The photovoltaic performances of plasmonic inverted organic solar cells (ITO/Au/ZnO/P3HT:PCBM/Ag) using spray-deposited Au and ZnO layers (both at 1 kV) showed improved efficiency. Fast exciton quenching in the P3HT:PCBM layer was achieved by using a spray-deposited Au layer in between ITO and ZnO layers. The absorption spectra and internal power conversion efficiency (IPCE) curve showed that the Au nanoparticles provide significant plasmonic broadband light absorption enhancement which resulted in the enhancement of the JSC value. Maximum efficiency of 3.6% was achieved for the inverted organic solar cell (IOSC) with an exceptionally high short circuit current density of ∼15 mA cm(-2) which is due to the additional photon absorption and the corresponding increase observed in the IPCE spectrum. The spray technique can be easily applied for the direct formation of Au nanoparticles in the fabrication of IOSC with improved performance over a large area.