Hemocompatibility challenge of membrane oxygenator for artificial lung technology.

The artificial lung (AL) technology is one of the membrane-based artificial organs that partly augments lung functions, i.e. blood oxygenation and CO2 removal. It is generally employed as an extracorporeal membrane oxygenation (ECMO) device to treat acute and chronic lung-failure patients, and the recent outbreak of the COVID-19 pandemic has re-emphasized the importance of this technology. The principal component in AL is the polymeric membrane oxygenator that facilitates the O2/CO2 exchange with the blood. Despite the considerable improvement in anti-thrombogenic biomaterials in other applications (e.g., stents), AL research has not advanced at the same rate. This is partly because AL research requires interdisciplinary knowledge in biomaterials and membrane technology. Some of the promising biomaterials with reasonable hemocompatibility - such as emerging fluoropolymers of extremely low surface energy - must first be fabricated into membranes to exhibit effective gas exchange performance. As AL membranes must also demonstrate high hemocompatibility in tandem, it is essential to test the membranes using in-vitro hemocompatibility experiments before in-vivo test. Hence, it is vital to have a reliable in-vitro experimental protocol that can be reasonably correlated with the in-vivo results. However, current in-vitro AL studies are unsystematic to allow a consistent comparison with in-vivo results. More specifically, current literature on AL biomaterial in-vitro hemocompatibility data are not quantitatively comparable due to the use of unstandardized and unreliable protocols. Such a wide gap has been the main bottleneck in the improvement of AL research, preventing promising biomaterials from reaching clinical trials. This review summarizes the current state-of-the-art and status of AL technology from membrane researcher perspectives. Particularly, most of the reported in-vitro experiments to assess AL membrane hemocompatibility are compiled and critically compared to suggest the most reliable method suitable for AL biomaterial research. Also, a brief review of current approaches to improve AL hemocompatibility is summarized. STATEMENT OF SIGNIFICANCE: The importance of Artificial Lung (AL) technology has been re-emphasized in the time of the COVID-19 pandemic. The utmost bottleneck in the current AL technology is the poor hemocompatibility of the polymer membrane used for O2/CO2 gas exchange, limiting its use in the long-term. Unfortunately, most of the in-vitro AL experiments are unsystematic, irreproducible, and unreliable. There are no standardized in-vitro hemocompatibility characterization protocols for quantitative comparison between AL biomaterials. In this review, we tackled this bottleneck by compiling the scattered in-vitro data and suggesting the most suitable experimental protocol to obtain reliable and comparable hemocompatibility results. To the best of our knowledge, this is the first review paper focusing on the hemocompatibility challenge of AL technology.

Effect of Additives during Interfacial Polymerization Reaction for Fabrication of Organic Solvent Nanofiltration (OSN) Membranes.

Thin film composite (TFC) membranes is the dominant type of desalination in the field of membrane technology. Most of the TFC membranes are fabricated via interfacial polymerization (IP) technique. The ingenious chemistry of reacting acyl chlorides with diamines at the interface between two immiscible phases was first suggested by Cadotte back in the 1980s, and is still the main chemistry employed now. Researchers have made incremental improvements by incorporating various organic and inorganic additives. However, most of the TFC membrane literature are focused on improving the water desalination performance. Recently, the application spectrum of membrane technology has been expanding from the aqueous environment to harsh solvent environments, now commonly known as Organic Solvent Nanofiltration (OSN) technology. In this work, some of the main additives widely used in the desalination TFC membranes were applied to OSN TFC membranes. It was found that tributyl phosphate (TBP) can improve the solubility of diamine monomer in the organic phase, and sodium dodecyl sulfate (SDS) surfactant can effectively stabilize the IP reaction interface. Employing both TBP and SDS exhibited synergistic effect that improved the membrane permeance and rejection in solvent environments.

The Roles of Membrane Technology in Artificial Organs: Current Challenges and Perspectives.

The recent outbreak of the COVID-19 pandemic in 2020 reasserted the necessity of artificial lung membrane technology to treat patients with acute lung failure. In addition, the aging world population inevitably leads to higher demand for better artificial organ (AO) devices. Membrane technology is the central component in many of the AO devices including lung, kidney, liver and pancreas. Although AO technology has improved significantly in the past few decades, the quality of life of organ failure patients is still poor and the technology must be improved further. Most of the current AO literature focuses on the treatment and the clinical use of AO, while the research on the membrane development aspect of AO is relatively scarce. One of the speculated reasons is the wide interdisciplinary spectrum of AO technology, ranging from biotechnology to polymer chemistry and process engineering. In this review, in order to facilitate the membrane aspects of the AO research, the roles of membrane technology in the AO devices, along with the current challenges, are summarized. This review shows that there is a clear need for better membranes in terms of biocompatibility, permselectivity, module design, and process configuration.

Blood Oxygenation Using Fluoropolymer-Based Artificial Lung Membranes.

Artificial lung (AL) membranes are used for blood oxygenation for patients undergoing open-heart surgery or acute lung failures. Current AL technology employs polypropylene and polymethylpentene membranes. Although effective, these membranes suffer from low biocompatibility, leading to undesired blood coagulation and hemolysis over a long term. In this work, we propose a new generation of AL membranes based on amphiphobic fluoropolymers. We employed poly(vinylidene-co-hexafluoropropylene), or PVDF-co-HFP, to fabricate macrovoid-free membranes with an optimal pore size range of 30-50 nm. The phase inversion behavior of PVDF-co-HFP was investigated in detail for structural optimization. To improve the wetting stability of the membranes, the fabricated membranes were coated using Hyflon AD60X, a type of fluoropolymer with an extremely low surface energy. Hyflon-coated materials displayed very low protein adsorption and a high contact angle for both water and blood. In the hydrophobic spectrum, the data showed an inverse relationship between the surface free energy and protein adsorption, suggesting an appropriate direction with respect to biocompatibility for AL research. The blood oxygenation performance was assessed using animal sheep blood, and the fabricated fluoropolymer membranes showed competitive performance to that of commercial polyolefin membranes without any detectable hemolysis. The data also confirmed that the bottleneck in the blood oxygenation performance was not the membrane permeance but rather the rate of mass transfer in the blood phase, highlighting the importance of efficient module design.