ABSTRACT
Positioning the positive pressure ventilator in front of the door opening affects the effectiveness of the rescue operation carried out during a fire. An important factor determining the effectiveness of the positive pressure ventilator is also the layout of the rooms within the gas exchange path and the obstacles present there. The purpose of this article is to assess the feasibility of using analyses such as large eddy simulation (LES) to verify the efficiency of mobile fans under simulation conditions, without the need for time-consuming experimentation (also for complex room volumes of buildings). The article presents a comparative analysis to assess the degree of convergence of flow parameters obtained during an experiment (in a multi-story building) and computational fluid dynamics (CFD) simulations. For volumetric flow rate, convergence was achieved at levels ranging from 0.4% (for 5 m) to 11.5% (1 m), and for pressure values, the differences achieved ranged from 0.6% (5 m) to 30.1% (4 m). This paper demonstrates that the LES model can be used to perform CFD simulations in the area of assessing the performance of a positive pressure ventilator. The article also describes a test methodology for determining the flow parameters of an air stream, which can be used to perform numerical simulations.
ABSTRACT
Air quality is one of the most important problems of the modern world, as it determines human health and changes occurring in other elements of nature, including climate change. For this reason, actions are taken to reduce the amount of harmful substances in the air. One such action is the use of building materials with special properties achieved by the application of self-cleaning coatings and photocatalytic additives. This article presents achievements in the field of additives and modifiers for building materials, whose task is to improve air quality. Concrete, cement, paints, and facade coatings modified based on the achievements of nanotechnology have been analyzed in terms of new properties and the possibility of their application in the area of modern environmental requirements. Both positive aspects and doubts were described in the scope of the effective reduction of the amount of gases such as VOC, NOx, dust and microorganisms.
ABSTRACT
Machines and devices for the production, transport and segregation of products are placed in production and storage rooms. Flat conveyor and drive belts are very often used for their construction. Due to heavy loads and difficult operating conditions, these belts can catch fire and, as a result, become the main source of air contaminants harmful to human health and life. This article examines the emission level of toxic chemical compounds most often produced during the thermal decomposition and combustion of flat drive and conveyor belts. Six types of flat belts, which were made of various polymer materials, i.e., polyamide, rubber, and polyurethane, and were pyrolyzed in a tube furnace at 950 °C, were tested for emission. Using an Fourier transform infrared spectroscopy gas analyser, five gaseous products of combustion were identified, i.e., carbon mono oxide, carbon dioxide, hydrogen cyanide, hydrogen bromide and sulfur dioxide (SO2). Chemical analysis showed that SO2 compounds and hydrogen bromide were present in only two samples. The test results indicate that gas emission concentration limits for all the tested belts were significantly exceeded. A comparative analysis of the concentration limits of V-belts described in the authors' earlier works shows that flat belts demonstrate lower emission levels of harmful compounds than V-belts. In addition, research has shown that compared to traditional rubber-based belts, belts made of modern materials exhibit no emission of hydrogen chloride compounds during thermal decomposition and combustion.
ABSTRACT
The article presents the potential impact of flat drive and transport belts on people's safety during a fire. The analysis distinguished belts made of classically used fabric-rubber composite materials reinforced with cord and currently used multilayer polymer composites. Moreover, the products' multilayers during the thermal decomposition and combustion can be a source of emissions for unpredictable and toxic substances with different concentrations and compositions. In the evaluation of the compared belts, a testing methodology was used to determine the toxicometric indicators (WLC50SM) on the basis of which it was possible to determine the toxicity of thermal decomposition and combustion products in agreement with the standards in force in several countries of the EU and Russia. The analysis was carried out on the basis of the registration of emissions of chemical compounds during the thermal decomposition and combustion of polymer materials at three different temperatures. Moreover, the degradation kinetics of the polymeric belts by using the thermogravimetric (TGA) technique was evaluated. Test results have shown that products of thermal decomposition resulting from the neoprene (NE22), leder leder (LL2), thermoplastic connection (TC), and extra high top cower (XH) belts can be characterized as moderately toxic or toxic. Their toxicity significantly increases with the increasing temperature of thermal decomposition or combustion, especially above 450 °C. The results showed that the belts made of several layers of polyamide can be considered the least toxic in fire conditions. The TGA results showed that NBR/PA/PA/NBR belt made with two layers of polyamide and the acrylonitrile-butadiene rubber has the highest thermal stability in comparison to other belts.
