Renal replacement therapy in patients on extracorporeal membrane oxygenation support: Who and how.

Patients undergoing extracorporeal membrane oxygenation (ECMO) support frequently develop renal failure requiring renal replacement therapy (RRT). RRT may be performed via a dialysis catheter based approach or via the ECMO circuit. We describe our experience with both techniques. A total of 68 patients undergoing ECMO support at our institution were retrospectively analyzed. Predictors of renal failure requiring RRT were determined. Patients undergoing RRT via a dialysis catheter were compared with those undergoing RRT via the ECMO circuit. 10 of the 68 patients required RRT support prior to ECMO. Of the remaining 58 patients, 25 (43%) required new RRT support on ECMO. Lower albumin levels and postcardiotomy shock were predictive of new renal failure requiring RRT on ECMO. RRT performed via the ECMO circuit demonstrated similar efficacy as via a dialysis catheter. Outcomes were much worse for patients requiring new RRT on ECMO support, with a doubling of the length of ECMO support and less that one-third the survival rate of patients not requiring RRT on ECMO support. New renal failure requiring RRT occurs in nearly one-half of patients on ECMO support, with poor outcomes. RRT may be performed via the ECMO circuit with similar efficacy as via a dialysis catheter.

Modified photon sieve as a high-performance bifocal and trifocal diffractive optical element.

We demonstrate that by dividing a Fresnel zone plate into a few regions having different periods in the s=r2 coordinate, then replacing the clear zones by a given distribution of pinholes, a so-called modified photon sieve is constructed. The first feature of the element is to increase its diameter without worrying about its feature size as the limiting factor in the fabrication zone plate. Moreover, it is shown that the number of the zones included in each region is an important parameter that has a great impact on handling the number of foci. So, by choosing a suitable relation between the number of the Fresnel zones of the regions, one gets a high-efficiency unifocal or bifocal or even multifocal element depending on the number of the regions and zones. This technique is detailed by making unifocal, bifocal, as well as trifocal modified photon sieves and surveying their focusing properties. Simulation studies are followed by the corresponding experiments to verify them.

Heparin sensitivity test for patients requiring cardiopulmonary bypass.

Anticoagulation for the open heart surgery patient undergoing cardiopulmonary bypass (CPB) is achieved with the use of heparin. The industry standard of activated clotting time (ACT) was used to measure the effect of heparin. The commonly acceptable target time of anticoagulation adequacy is 480 seconds or greater. Some patients, however, exhibit resistance to standard dosing of heparin and do not reach target anticoagulation time (480 seconds). Antithrombin III deficiency has been previously cited as the cause of heparin resistance. Early detection of heparin resistance (HR) may avoid both the delayed start of CPB and inadequate anticoagulation, if emergency bypass is required. An anticoagulation sensitivity test (AST) was developed by adding 12 units of porcine mucosa heparin to the ACT tube (International Technidyne, celite type). Before anticoagulation, 4 mL of blood was drawn from the patient arterial line. Following the manufacturer's instructions, 2 mL of blood was added to each tube (ACT-baseline and ACT-AST). Three minutes after anticoagulation with 4 mg heparin/kg body weight, a second sample (ACT-CPB) was taken to determine anticoagulation adequacy. The ACT times of each sample were recorded for 300 procedures occurring during 2004 and were retrospectively reviewed. Heparin resistance occurred in approximately 20% of the patients (n = 61). In 54 patients, heparin resistance was predicted by the ACT-AST. This was determined by the presence of an ACT-AST time and an ACT-CPB that were both < 480 seconds. The positive predictive value was 90%, with a false positive rate of 3%. Heparin resistance occurs in patients undergoing CPB. We describe a simple and reliable test to avoid the delays of assessing anticoagulation for CPB (90% positive predictive value). Depending on program guidelines, patients can be given additional heparin or antithrombin III derivatives to aid in anticoagulation. An additional ACT must be performed and reach target times before CPB initiation. Testing of patient blood before the time of incision for sensitivity to heparin is a way to avoid a delay that can be critical in the care of the patient. Commercial tests are available, but efficacy data are limited, and they lead to added inventory expense. This method of titrating a diluted heparin additive, mixed with patient blood in a familiar ACT test, has proven to be an inexpensive and reliable test to predict patient's sensitivity to heparin.