ABSTRACT
The combination of plasmonic nanoparticles and graphene enhances the responsivity and spectral selectivity of graphene-based photodetectors. However, the small area of the metal-graphene junction, where the induced electron-hole pairs separate, limits the photoactive region to submicron length scales. Here, we couple graphene with a plasmonic grating and exploit the resulting surface plasmon polaritons to deliver the collected photons to the junction region of a metal-graphene-metal photodetector. This gives a 400% enhancement of responsivity and a 1000% increase in photoactive length, combined with tunable spectral selectivity. The interference between surface plasmon polaritons and the incident wave introduces new functionalities, such as light flux attraction or repulsion from the contact edges, enabling the tailored design of the photodetector's spectral response. This architecture can also be used for surface plasmon biosensing with direct-electric-redout, eliminating the need of bulky optics.
Subject(s)
Biosensing Techniques , Graphite/chemistry , Metals/chemistry , Nanoparticles/chemistry , Light , Nanotechnology/methods , Photons , Surface Plasmon ResonanceABSTRACT
Graphene's high mobility and Fermi velocity, combined with its constant light absorption in the visible to far-infrared range, make it an ideal material to fabricate high-speed and ultrabroadband photodetectors. However, the precise mechanism of photodetection is still debated. Here, we report wavelength and polarization-dependent measurements of metal-graphene-metal photodetectors. This allows us to quantify and control the relative contributions of both photothermo- and photoelectric effects, both adding to the overall photoresponse. This paves the way for a more efficient photodetector design for ultrafast operating speeds.
ABSTRACT
From the wide spectrum of potential applications of graphene, ranging from transistors and chemical sensors to nanoelectromechanical devices and composites, the field of photonics and optoelectronics is believed to be one of the most promising. Indeed, graphene's suitability for high-speed photodetection was demonstrated in an optical communication link operating at 10 Gbit s(-1). However, the low responsivity of graphene-based photodetectors compared with traditional III-V-based ones is a potential drawback. Here we show that, by combining graphene with plasmonic nanostructures, the efficiency of graphene-based photodetectors can be increased by up to 20 times, because of efficient field concentration in the area of a p-n junction. Additionally, wavelength and polarization selectivity can be achieved by employing nanostructures of different geometries.
ABSTRACT
The truly two-dimensional material graphene is an ideal candidate for nanoelectromechanics due to its large strength and mobility. Here we show that graphene flakes provide natural nanomembranes of diameter down to 3 nm within its intrinsic rippling. The membranes can be lifted either reversibly or hysteretically by the tip of a scanning tunneling microscope. The clamped-membrane model including van-der-Waals and dielectric forces explains the results quantitatively. AC-fields oscillate the membranes, which might lead to a completely novel approach to controlled quantized oscillations or single atom mass detection.
Subject(s)
Graphite/chemistry , Nanostructures/chemistry , Nanotechnology/methods , Silicon Dioxide/chemistry , Adsorption , Membranes, Artificial , Microscopy, Scanning Tunneling/methods , Models, Statistical , Oscillometry , Static Electricity , Time FactorsABSTRACT
Using scanning tunneling microscopy in an ultrahigh vacuum and atomic force microscopy, we investigate the corrugation of graphene flakes deposited by exfoliation on a Si/SiO2 (300 nm) surface. While the corrugation on SiO2 is long range with a correlation length of about 25 nm, some of the graphene monolayers exhibit an additional corrugation with a preferential wavelength of about 15 nm. A detailed analysis shows that the long-range corrugation of the substrate is also visible on graphene, but with a reduced amplitude, leading to the conclusion that the graphene is partly freely suspended between hills of the substrate. Thus, the intrinsic rippling observed previously on artificially suspended graphene can exist as well, if graphene is deposited on SiO2.
