A voltammetric method coupled with chemometrics for determination of a ternary antiparkinson mixture in its dosage form: greenness assessment.

An electroanalytical methodology was developed by direct differential pulse voltammetric (DPV) measurement of Levodopa (LD), Carbidopa (CD) and Entacapone (ENT) mixture using bare glassy carbon electrode (GCE) in Britton Robinson (BR) buffer (pH = 2.0). A multivariate calibration model was then applied to the exported preprocessed voltammetric data using partial least square (PLS) as a chemometric tool. Additionally, the model was cross-validated and the number of latent variables (LVs) were determined to produce a reliable model for simultaneous quantitation of the three drugs either in their synthetic mixtures or in their marketed pharmaceutical formulation with high accuracy and precision. Data preprocessing was used to tackle the problem of lacking bi-linearity which is commonly found in electrochemical data. The proposed chemometric model was able to provide fast and reliable technique for quantitative determination of antiparkinson drugs in their dosage forms. This was successfully achieved by utilizing sixteen mixtures as calibration set and nine mixtures as validation set. The percent recoveries for LD, CD and ENT were found to be 100.05% ± 1.28%, 100.04% ± 0.53% and 99.99% ± 1.25%, respectively. The obtained results of the proposed method were statistically compared to those of a previously reported High Performance Liquid Chromatography (HPLC) methodology. Finally, the presented analytical method strongly supports green analytical chemistry regarding the minimization of potentially dangerous chemicals and solvents, as well as reducing energy utilization and waste generation.

A novel electrochemical hybrid platform for sensitive determination of the aminoglycoside antibiotic Kasugamycin residues in vegetables.

Kasugamycin residues (KASU), a pest control antibiotic, was reported as an ecosystem threat owing to its over-application in plant protection to meet the growing global need for agronomic products. Therefore, we report herein the first electrochemical sensor for fast and sensitive analysis of KASU in vegetables based on the synergetic hybridization between conducting polyserine film (poly (SER)), and carbon nanomaterials including functionalized multiwalled carbon nanotubes (fMWCNTs) and reduced graphene oxide (rGO). The sensor was characterized morphologically using Scanning electron (SEM) and atomic force Microscopy (AFM), while cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) were used for electrochemical characterization. Under the optimized conditions using differential pulse voltammetry (DPV), the sensor exhibited an outstanding sensitivity and selectivity, with a good linear response of 3-106 µg/mL and an assessed limit of detection and quantification of 0.40 and 1.33 µg/mL, respectively. Furthermore, the electrochemical sensor was effectively applied to quantify KASU in cucumber, zucchini, and carrots with a recovery range 95.5-100.1%, and RSD lower than 4.1% (n = 3), showing its applicability and efficiency for selective analysis of KASU in foodstuffs.

Synthesis and Characterization of Orange Peel Modified Hydrogels as Efficient Adsorbents for Methylene Blue (MB).

In recent years, due to the developments in the textile industry, water contaminated with synthetic dyes such as methylene blue (MB) has become an environmental threat based on the possible impacts in terms of chemical and biochemical demand, which leads to disturbance in aquatic plants photosynthesis, besides their possible toxicity and carcinogenicity for humans. In this work, an adsorbent hydrogel is prepared via free radical polymerization comprising acrylic acid (PAA) as a monomer and orange peel (OP) as a natural modifier rich in OH and COOH present in its cellulose and pectin content. The resulting hydrogels were optimized in terms of the content of OP and the number of cross-linkers and characterized morphologically using Scanning electron microscopy. Furthermore, BET analysis was used to follow the variation in the porosity and in terms of the surface area of the modified hydrogel. The adsorption behavior was found to follow pseudo-second-order as a kinetic model, and Langmuir, Freundlich, and Temkin isotherm models. The combination of OP and PAA has sharply enhanced the adsorption percent of the hydrogel to reach 84% at the first 10 min of incubation with an adsorption capacity of more than 1.93 gm/gm. Due to its low value of pHPZc, the desorption of MB was efficiently performed at pH 2 using HCl, and the desorbed OP-PAA were found to be reusable up to ten times without a decrease in their efficiency. Accordingly, OP-PAA hydrogel represents a promising efficient, cost-effective, and environmentally friendly adsorbent for MB as a model cationic dye that can be applied for the treatment of contaminated waters.

Fabrication of nanostructured lipid carriers ocugel for enhancing Loratadine used in treatment of COVID-19 related symptoms: statistical optimization, in-vitro, ex-vivo, and in-vivo studies evaluation.

Loratadine (LORA), is a topical antihistamine utilized in the treatment of ocular symptoms of COVID-19. The study aimed to develop a Loratadine Nanostructured Lipid Carriers Ocugel (LORA-NLCs Ocugel), enhance its solubility, trans-corneal penetrability, and bioavailability. full-factorial design was established with 24 trials to investigate the impact of several variables upon NLCs properties. LORA-NLCs were fabricated by using hot melt emulsification combined with high-speed stirring and ultrasonication methods. All obtained formulae were assessed in terms of percent of entrapment efficiency (EE%), size of the particle (PS), zeta potential (ZP), as well as in-vitro release. Via using Design Expert® software the optimum formula was selected, characterized using FTIR, Raman spectroscopy, and stability studies. Gel-based of optimized LORA-NLCs was prepared using 4% HPMC k100m which was further evaluated in terms of physicochemical properties, Ex-vivo, and In-vivo studies. The optimized LORA-NLCs, comprising Compritol 888 ATO®, Labrasol®, and Span® 60 showed EE% of 95.78 ± 0.67%, PS of 156.11 ± 0.54 nm, ZP of -40.10 ± 0.55 Mv, and Qh6% of 99.67 ± 1.09%, respectively. Additionally, it illustrated a spherical morphology and compatibility of LORA with other excipients. Consequently, gel-based on optimized LORA-NLCs showed pH (7.11 ± 0.52), drug content (98.62%± 1.31%), viscosity 2736 cp, and Q12% (90.49 ± 1.32%). LORA-NLCs and LORA-NLCs Ocugel exhibited higher ex-vivo trans-corneal penetrability compared with the aqueous drug dispersion. Confocal laser scanning showed valuable penetration of fluoro-labeled optimized formula and LORA-NLCs Ocugel through corneal. The optimized formula was subjected to an ocular irritation test (Draize Test) that showed the absence of any signs of inflammation in rabbits, and histological analysis showed no effect or damage to rabbit eyeballs. Cmax and the AUC0-24 were higher in LORA-NLCs Ocugel compared with pure Lora dispersion-loaded gel The research findings confirmed that NLCs could enhance solubility, trans-corneal penetrability, and the bioavailability of LORA.

Nanomicelles-in-coaxial nanofibers with exit channels as a transdermal delivery platform for smoking cessation.

Smoking is a life-threatening habit; that is why many nicotine-replacement therapies (NRTs), which include chewing gums, nicotine patches, lozenges, mouth sprays, inhalers and nasal sprays that are usually administered for 8-12 weeks, have been reported for smoking cessation. We report the fabrication of patches comprising nanomicelles-in-coaxial nanofibers (NFs) for the transdermal delivery of varenicline (VAR) tartrate, a partial agonist of the α4ß2 receptor subtype, for smoking cessation. The cores of the fabricated coaxial NF structures are composed of polyethylene oxide, VAR-loaded Pluronic F127 nanomicelles (NPs) and free VAR, while the shell consists of a blend of cellulose acetate (CA) and polycaprolactone (PCL) in a ratio of 1 : 9 (w/w) that incorporates 50% (wt%) free VAR. The morphology and the coaxial structure of the NFs were investigated using TEM, SEM and fluorescent microscopy. The physicochemical and mechanical properties of the scaffolds were analyzed using FTIR, DSC, DLS, TGA and a universal testing machine. SEM micrographs depict NFs with a size ranging from 793.7 ± 518.9 to 324.5 ± 144.1 nm. In vitro release of VAR reaches almost 100% after 3, 9 and 28 days for free VAR, VAR-loaded NPs and the NPs-in-NFs patches, respectively, while the ex vivo release tested using albino rat skin, over a period of 60 days, showed up to 94% sustained release of VAR. Besides, skin permeation, in vivo release and plasma concentrations of VAR from the NF transdermal patches were monitored via cyclic voltammetric measurements during the course of treatment. DFT calculations as well as mathematical release kinetic models were performed in order to study the release mechanism. The cell viability of human skin fibroblast (HSF) cells in the case of plain and VAR-loaded NFs was 75.09 and 32.11%, respectively. The in vivo results showed that VAR was being continuously released from the transdermal patch over a period of 14 days. Besides, the treatment with VAR-loaded patches did not cause any severe conditions in the studied animal model. The new fabricated NPs-in-NFs transdermal patch for VAR tartrate delivery is considered as an effective, economic, safe and long-acting NRT for smoking cessation.

Application of Molecularly Imprinted Polymers in the Analysis of Waters and Wastewaters.

The increase of the global population and shortage of renewable water resources urges the development of possible remedies to improve the quality and reusability of waste and contaminated water supplies. Different water pollutants, such as heavy metals, dyes, pesticides, endocrine disrupting compounds (EDCs), and pharmaceuticals, are produced through continuous technical and industrial developments that are emerging with the increasing population. Molecularly imprinted polymers (MIPs) represent a class of synthetic receptors that can be produced from different types of polymerization reactions between a target template and functional monomer(s), having functional groups specifically interacting with the template; such interactions can be tailored according to the purpose of designing the polymer and based on the nature of the target compounds. The removal of the template using suitable knocking out agents renders a recognition cavity that can specifically rebind to the target template which is the main mechanism of the applicability of MIPs in electrochemical sensors and as solid phase extraction sorbents. MIPs have unique properties in terms of stability, selectivity, and resistance to acids and bases besides being of low cost and simple to prepare; thus, they are excellent materials to be used for water analysis. The current review represents the different applications of MIPs in the past five years for the detection of different classes of water and wastewater contaminants and possible approaches for future applications.

Application of a Conducting Poly-Methionine/Gold Nanoparticles-Modified Sensor for the Electrochemical Detection of Paroxetine.

This work demonstrates a facile electropolymerization of a dl-methionine (dl-met) conducting polymeric film on a gold nanoparticle (AuNPs)-modified glassy carbon electrode (GCE). The resulting sensor was successfully applied for the sensitive detection of paroxetine·HCl (PRX), a selective serotonin (5-HT) reuptake inhibitor (SSRIs), in its pharmaceutical formulations. The sensor was characterized morphologically using scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDX) and atomic force microscopy (AFM) and electrochemical techniques such as differential pulse voltammetry (DPV), electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The proposed sensor, poly (dl-met)/AuNPs-GCE, exhibited a linear response range from 5 × 10-11 to 5 × 10-8 M and from 5 × 10-8 to 1 × 10-4 M using DPV with lowest limit of detection (LOD = 1 × 10-11 M) based on (S/N = 3). The poly (dl-met)/AuNPs-GCE sensor was successfully applied for PRX determination in three different pharmaceutical formulations with percent recoveries between 96.29% and 103.40% ± SD (±0.02 and ±0.58, respectively).

Molecularly Imprinted Electrochemical Sensor-Based Fe2O3@MWCNTs for Ivabradine Drug Determination in Pharmaceutical Formulation, Serum, and Urine Samples.

Ivabradine hydrochloride (IVR) is a medically important drug because of its ability to lower the heart rate. Techniques reported for IVR determination were expensive, laborious, besides being of poor selectivity. In this study, iron oxide @ carbon nanotube (Fe2O3@MWCNTs) nanocomposite and molecularly imprinted polymer (MIP) were synthesized and used in the fabrication of carbon paste electrodes (CPEs) for the potentiometric detection of IVR in biological and pharmaceutical samples. CPEs of the best sensor were formulated from graphite (41 wt%) as a carbon source, MIP (3 wt.%) as an ionophore, Fe2O3@MWCNTs (5 wt%) as a modifier, and nitrophenyl octyl ether (NPOE, 51 wt.%) as a conductive oil so-called plasticizer. The best sensor exhibits a Nernstian slope (response) of 56 mV decade-1 within the IVR concentration range from 1.0 × 10-3 M to 9.8 × 10-8 M with high selectivity against interfering species (ascorbic, maltose, glucose, lactose, dopamine, glycine) over those reported earlier. The use of Fe2O3@MWCNTs together with MIP in the electrode formulation was found to improve the limit of detection (LOD) from 630 to 98 nM along with high reversibility, a short response time of 30 s, and a good lifetime of more than 2 weeks. The sandwich membrane (SMM) method was used to quantify the H-bonding complexing strength of the MIP binding sites for IVR with Log ß ILn = 11.33. The constructed sensors were successfully applied for the IVR determination in blood serum, urine, and commercial formulations (Savapran®) with high sensitivity.

t-Butyl calixarene/Fe2O3@MWCNTs composite-based potentiometric sensor for determination of ivabradine hydrochloride in pharmaceutical formulations.

Ivabradine hydrochloride (IVB) has shown high medical importance as it is a medication for lowering the heart rate for the symptomatic chronic heart failure and symptomatic management of stable angina pectoralis. The high dose of IVB may cause severe and prolonged bradycardia, uncontrolled blood pressure, headache, and blurred vision. In this study, a highly sensitive carbon-paste electrode (CPEs) was constructed for the potentiometric determination of IVB in pharmaceutical formulations. t-Butyl calixarene (t-BCX) was used as an ionophore due to its ability to mask IVB in the cavity via multiple H-bonding at the lower rim, as estimated quantitatively by the sandwich membrane method (Log ßILn = 8.62). Besides, the use of multi-walled carbon nanotubes decorated with Fe2O3 nanoparticles (Fe2O3@MWCNTs) as an additive for the paste electrode significantly improved the detection limit of the sensor up to 36 nM, with Nernstian response of 58.9 mV decade-1 in the IVB linear dynamic range of 10-3-10-7 M in aqueous solutions. The constructed sensors showed high selectivity against interfering species that may exist in physiological fluids or pharmaceutical formulations (e.g. Na+, K+, NH4+, Ca2+, Mg2+, Ba2+, Fe3+, Co2+, Cr3+, Sr2+, glucose, lactose, maltose, glycine, dopamine, and ascorbic acid). The sensors were successfully employed for IVB determination in the pharmaceutical formulations (Savapran®).

Calixarene-doped PVC polymeric films as size-selective optical sensors: Monitoring of salicylate in real samples.

Preparation of novel salicylate-selective optical sensors (bulk optodes) was performed and applied successfully for salicylate determination in pharmaceutical formulations, Aspirin® and Aspocid®. t-butyl calix[4]arene ionophore was incorporated in a plasticized poly (vinyl-chloride) membrane containing the chromoionophore ETH5294 (O1) or ETH7075 (O5). The optical response to salicylate was due to size-selective extraction of salicylate from the aqueous solution to the optode bulk through formation of hydrogen bond accompanied by chromoionophore protonation, that resulted in the optical response at 680 or 540 nm for O1 or O5, respectively. Reliable size-selectivity was measured for salicylate over other anions; The calculated selectivity coefficients of O5 optode were found to be: -4.4, -2.0 and - 3.7 for iodide, benzoate and perchlorate, respectively. The hydrogen bonding mechanism and selectivity pattern were ensured and explained by IR and 1H NMR spectroscopy. For the same purpose, a molecular recognition constant of ßsal=100.043 was calculated using sandwich membrane method, and its small value ensured that hydrogen bonding interaction is responsible for the optode response. The detection limits of O1 and O5 in salicylate buffered solutions were 9.0 × 10-5 and 8.9 × 10-5 M with response times of 5 and 3 min, respectively, and with very good reversibility. The practical utility of the developed sensors was ensured by salicylate determination in Aspirin® and Aspocid®. Beyond the observed analytical performance, the present work aims not only to effectively apply Calixarene without derivatization, but also to estimate the strength of the size-dependent hydrogen bonding and comprehensively study the interaction mechanism.

Isolation of sinapic acid from broccoli using molecularly imprinted polymers.

A molecularly imprinted polymer was synthesized for the purpose of sinapic acid isolation from Egyptian nutraceutical Botrytis italica, L. (broccoli) due to its prominent medicinal and wide pharmacological activities. A computational study was first developed to determine the optimal template to functional monomer molar ratio. Based on the computational results, five polymers were synthesized using a bulk polymerization method with sinapic acid as the template molecule. Evaluation of the synthesized polymers binding performance was carried out using batch rebinding assay, which revealed that the molecularly imprinted polymer of molar ratio (1:4:20), template to functional monomer (4-vinyl pyridine) to crosslinker (ethylene glycol dimethacrylate) was of optimum performance, thus, this polymer was applied for sinapic acid isolation from closely related analogues. This represents a more practical approach to isolate sinapic acid from different natural extracts selectively.

Enantiomeric separation of underivatized amino acids: predictability of chiral recognition on ristocetin a chiral stationary phase.

The present work aimed to investigate the predictability of the chromatographic behavior for the separation of underivatized amino acids on ristocetin A, known as Chirobiotic R, using a DryLab high-performance liquid chromatography (HPLC) method development software, which is typically used to predict the effect of changing various chromatographic parameters on resolution in the reversed phase mode. After implementing the basic runs, and judging the predictability via the computed resolution map, it can be deduced that the chiral recognition mechanisms tend towards a hydrophilic interaction chromatography rather than the reversed phase mode, which limits the ability of DryLab software to predict separations on Chirobiotic R.

Predictability of enantiomeric chromatographic behavior on various chiral stationary phases using typical reversed phase modeling software.

Pharmaceutical companies worldwide tend to apply chiral chromatographic separation techniques in their mass production strategy rather than asymmetric synthesis. The present work aims to investigate the predictability of chromatographic behavior of enantiomers using DryLab HPLC method development software, which is typically used to predict the effect of changing various chromatographic parameters on resolution in the reversed phase mode. Three different types of chiral stationary phases were tested for predictability: macrocyclic antibiotics-based columns (Chirobiotic V and T), polysaccharide-based chiral column (Chiralpak AD-RH), and protein-based chiral column (Ultron ES-OVM). Preliminary basic runs were implemented, then exported to DryLab after peak tracking was accomplished. Prediction of the effect of % organic mobile phase on separation was possible for separations on Chirobiotic V for several probes: racemic propranolol with 97.80% accuracy; mixture of racemates of propranolol and terbutaline sulphate, as well as, racemates of propranolol and salbutamol sulphate with average 90.46% accuracy for the effect of percent organic mobile phase and average 98.39% for the effect of pH; and racemic warfarin with 93.45% accuracy for the effect of percent organic mobile phase and average 99.64% for the effect of pH. It can be concluded that Chirobiotic V reversed phase retention mechanism follows the solvophobic theory.

Determination of the design space of the HPLC analysis of water-soluble vitamins.

Analysis of water-soluble vitamins has been tremendously approached through the last decades. A multitude of HPLC methods have been reported with a variety of advantages/shortcomings, yet, the design space of HPLC analysis of these vitamins was not defined in any of these reports. As per the food and drug administration (FDA), implementing the quality by design approach for the analysis of commercially available mixtures is hypothesized to enhance the pharmaceutical industry via facilitating the process of analytical method development and approval. This work illustrates a multifactorial optimization of three measured plus seven calculated influential HPLC parameters on the analysis of a mixture containing seven common water-soluble vitamins (B1, B2, B6, B12, C, PABA, and PP). These three measured parameters are gradient time, temperature, and ternary eluent composition (B1/B2) and the seven calculated parameters are flow rate, column length, column internal diameter, dwell volume, extracolumn volume, %B (start), and %B (end). The design is based on 12 experiments in which, examining of the multifactorial effects of these 3 + 7 parameters on the critical resolution and selectivity, was carried out by systematical variation of all these parameters simultaneously. The 12 basic runs were based on two different gradient time each at two different temperatures, repeated at three different ternary eluent compositions (methanol or acetonitrile or a mixture of both). Multidimensional robust regions of high critical R(s) were defined and graphically verified. The optimum method was selected based on the best resolution separation in the shortest run time for a synthetic mixture, followed by application on two pharmaceutical preparations available in the market. The predicted retention times of all peaks were found to be in good match with the virtual ones. In conclusion, the presented report offers an accurate determination of the design space for critical resolution in the analysis of water-soluble vitamins by HPLC, which would help the regulatory authorities to judge the validity of presented analytical methods for approval.

Dissolution testing and potentiometric determination of famciclovir in pure, dosage forms and biological fluids.

The performance characteristics of two new plastic membrane ion selective electrodes (ISEs) used for the determination of famciclovir (Fcv) based on the ion associate of Fcv with phosphotungstic acid (PTA) or phosphomolybdic acid (PMA) are described. Different experimental conditions as type of plasticizer to be incorporated in the membrane, life span, effect of soaking, pH, temperature, and interferences were studied. Both electrodes showed similar performance under these conditions, exhibiting Nernstian slopes of S (Fcv-PTA)=58.60±0.84 mV/decade and S (Fcv-PMA)=58.77±0.68 mV/decade within a usable concentration range of 10⁻5-10⁻² [Fcv/M] at 298/K. Famciclovir was assayed potentiometrically in its pure solution, pharmaceutical preparations and biological fluids (urine and plasma) using proposed electrodes under batch and flow injection analysis (FIA) conditions with a recovery % ranging between 96.76% and 102.83% having RSD of 0.66%-1.81%. The electrodes were also successfully applied in the determination of the dissolution profile of Fcv tablets and the results came in agreement with the validated results of the HPLC method obtained from the quality control unit of the company producing the tablets.

Potentiometric determination of tolterodine in batch and flow injection conditions.

Two new ion-selective electrodes of the plastic membrane type for the determination of Tolterodine (Tol) were prepared. These electrodes depend on the incorporation of the ion-exchangers of the above mentioned drug with phosphotungestic acid (PTA) or Silicotungestic acid (STA) in a PVC matrix. A comparative study is made between the performance characteristics of electrodes containing ion-exchanger in batch and FIA conditions. The usable concentration range of the electrodes was found to be (1.0×10(-5)-1.0×10(-2) and 5.0×10(-5)-1.0×10(-2)M) in batch and FIA conditions, respectively. The electrodes have nearly the same usable concentration, pH range and exhibited high selectivity toward Tol in the presence of many inorganic cations and can be used in biological fluids such as urine and plasma. The dissolution profile of the investigated drug as well as its assay in pure and pharmaceutical preparations was performed, and the results were relatively accurate and precise as indicated by the recovery values and coefficients of variation.

Construction and performance characteristics of new ion selective electrodes based on carbon nanotubes for determination of meclofenoxate hydrochloride.

This work offers construction and comparative evaluation the performance characteristics of conventional polymer (I), carbon paste (II) and carbon nanotubes chemically modified carbon paste ion selective electrodes (III) for meclofenoxate hydrochloride are described. These electrodes depend mainly on the incorporation of the ion pair of meclofenoxate hydrochloride with phosphomolybdic acid (PMA) or phosphotungestic acid (PTA). They showed near Nernestian responses over usable concentration range 1.0 × 10(-5) to 1.0 × 10(-2)M with slopes in the range 55.15-59.74 mV(concentrationdecade)(-1). These developed electrodes were fully characterized in terms of their composition, response time, working concentration range, life span, usable pH and temperature range. The electrodes showed a very good selectivity for Meclo with respect to a large number of inorganic cations, sugars and in the presence of the degradation product of the drug (p-chloro phenoxy acetic acid). The standard additions method was applied to the determination of MecloCl in pure solution, pharmaceutical preparations and biological samples. Dissolution testing was also applied using the proposed sensors.

Application of oxybutynin selective sensors for monitoring the dissolution profile and assay of pharmaceutical dosage forms.

Two ion-selective sensors of the plastic membrane type were prepared for the determination of oxybutynin hydrochloride (OxCl). They depend on the incorporation of the ion-associates with phosphotungestic acid or phosphomolybdic acid in a PVC matrix. A comparative study is made between their performance characteristics in batch and FIA conditions. The sensors have nearly the same usable concentration, temperature and pH range. They have a wide range of selectivity and can be applied for the determination of the relevant drug with nearly the same precision and accuracy in vitro. Dissolution testing was applied using the sensors; this offers a simple, rapid, cheap way out of sophisticated and high cost instruments used in the pharmacopeial method using HPLC. The investigated drug was determined in its pure and pharmaceutical preparations. The results were accurate and precise, as indicated by the recovery values and coefficients of variation.

Flow injection potentiometric assay of hexoprenaline in its pure state, pharmaceutical preparations, and biological samples.

Different hexoprenaline (Hx(2)SO(4)) conventional and coated wire electrodes were constructed and evaluated. Membranes were based on hexoprenalinium phosphotungstate (Hx-PTA) and hexporenalinium phosphomolybdate (Hx-PMA). The electrodes were fully characterized in terms of their composition, response time, life span, pH, and temperature and then were applied to the potentiometric determination of the hexoprenalinium ion in its pure state, pharmaceutical preparations, and biological samples, urine and plasma, under batch and flow injection conditions. The selectivity of the electrodes towards many inorganic cations, sugars, amino acids, and some other brochodilatures of close chemical composition was also tested.