ABSTRACT
Post-weld heat treatment (PWHT) and solid-state thermomechanical treatment (TMT) via friction stir processing (FSP) have been shown to enhance the mechanical properties of aluminum alloys. The current work investigates the effects of PWHT and TMT on the microstructure and mechanical performance of AA6082-T6 welded butt joints welded using the MIG process. The 5 mm thick AA 6082-T6 plates were joined in butt configuration using MIG welding with ER 5356 filler wire, 120 A current, 0.3 mm/s weld speed, and argon shielding gas at 15 L/min flow rate. PWHT was performed on the MIG welds per the T6 temper procedure. TMT was implemented via FSP using a pinless tool rotating at 800 rpm and traversing speed at 200 mm/min with a 3° tilt angle. Microstructural analysis, hardness mapping, tensile testing, and fracture surface evaluation were utilized to characterize the as-welded, PWHT, and TMT samples. The results demonstrate that both PWHT and TMT significantly refine and homogenize the microstructures of the welded joints. However, the TMT samples displayed superior hardness and tensile strength compared to the as-welded and PWHT conditions. The TMT-processed welds achieved approximately 99% joint efficiency versus only 69% and 85% for the as-welded and PWHT samples. In summary, PWHT and especially TMT via FSP are effective at enhancing the mechanical properties of MIG welded AA6082-T6.
ABSTRACT
Welding of dissimilar aluminum alloys has been widely used in many industrial applications. However, the selection of filler type still attracts significant interest in the welding research area. The present work concerns the effect of filler metal on the microstructure and corrosion of weld joints of dissimilar aluminum alloys. AA 5083 and AA 6082 alloys were welded by tungsten inert gas welding (GTAW) using filler metals ER 4043 and ER 5356. The microstructure observations and the corrosion test of the weld joints were carried out. Solidification cracks were observed in the ER 4043 weld zone, whereas defect-free joints were obtained using a mix filler welding process. A galvanic corrosion was observed on the boundary between the filler rod ER 4043 weld zone and AA 5083 base alloy. From the corrosion standpoint of view, the using of ER 4043 electrodes is not preferred for welding 5000 series aluminum alloys, whereas ER 5356 filler electrode is more favorable than ER 4043 filler electrode either for dissimilar welding of AA 5083 and AA 6082 alloys or individual welding of both aluminum alloys. No galvanic corrosion is observed between ER 4043 fillers and AA 6082 base alloy.
ABSTRACT
Al-Al2O3 and SiC metal matrix composites (MMCs) samples with different volume fractions up to 20% were produced by high-pressure torsion (HPT) using 10 GPa for 30 revolutions of Al-Al2O3, and SiC and powder metallurgy (PM). The effect of the processing method of micro-size Al MMCs on the density, microstructure evolution, mechanical properties, and tensile fracture mode was thoroughly investigated. HPT processing produces fully dense samples relative to those produced using powder metallurgy (PM). The HPT of the Al MMCs reduces the Al matrix grain size and fragmentation of the reinforcement particles. The Al matrix average grain size decreased to 0.39, 0.23, and 0.2 µm after the HPT processing of Al, Al-20% Al2O3, and SiC samples. Moreover, Al2O3 and SiC particle sizes decreased from 31.7 and 25.5 µm to 0.15 and 0.13 µm with a 99.5% decrease. The production of ultrafine grain (UFG) composite samples effectively improves the microhardness and tensile strength of the Al and Al MMCs by 31-88% and 10-110% over those of the PM-processed samples. The good bonding between the Al matrix and reinforcement particles noted in the HPTed Al MMCs increases the strength relative to the PM samples. The tensile fracture surface morphology results confirm the tensile properties results.
ABSTRACT
The influence of the number of passes and the tube materials on the microstructural evolution, mechanical properties, and wear behavior of Cu and brass tubes after parallel tubular channel angular pressing (PTCAP) was investigated. The grain size decreased to final grain sizes of 138.6 nm and 142.7 nm, after PTCAP of the Cu and brass tubes was conducted in up to 4 and 2 passes, respectively. PTCAP contributes to obtaining an ultra-fine grain (UFG) microstructure, with a mixture of different grain sizes that conferred high hardness. The present results indicate the superior wear resistance of Cu and brass PTCAP tubes, relative to Cu and brass samples that were previously deformed by different severe plastic deformation (SPD) processes. The wear mechanism of the Cu tubes changed from delamination and cracks with a high degree of adhesive wear before PTCAP into a combination of adhesive and abrasive wear, with a decrease in the presence of oxygen content after the PTCAP procedure. The wear mechanism also changed from a combination of adhesive and abrasive mechanisms into abrasive ones with the absence of oxygen after the PTCAP of brass tubes.
ABSTRACT
The motivation for the current study was to improve the wear and frictional properties of Al, Al-Al2O3, and SiC MMCs through HPT processing. The wear test using a tungsten carbide (WC) ball was carried out for different PM and HPT-processed Al and MMC samples. The effect of the sample processing methods on the wear rate, friction, and wear surface morphology was thoroughly investigated. The high hardness after Al grain refinement and reinforcement fragmentation through the HPT processing of the samples increased the wear resistance by 16-81% over that of the PM samples. The average coefficient values and variation ranges were reduced after HPT processing. The Al and Al MMC processing methods affected the wear mechanism and surface morphologies, as proven by the microscopic observations and analyses of the worn surfaces of the samples and WC balls.
