How does continuous venovenous hemofiltration theoretically expose (ex-vivo models) inpatients to diethylhexyladipate, a plasticizer of PVC medical devices?

Continuous venovenous hemofiltration (CVVH) is widely used in intensive care units to treat patients with acute kidney injury requiring renal replacement therapy. The medical devices (MD) used for CVVH include a hemofilter and tubings made of plasticized PVC. Due to its known reprotoxicity, diethylhexyl phthalate (DEHP) has been replaced by alternatives such as diethylhexyladipate (DEHA) in some of these tubings. The migration of DEHA from hemofiltration systems has not been assessed and thus the level of patient exposure to this DEHP-alternative remains unknown. In this study, 2 CVVH models were used to evaluate the potential migration of DEHA from PVC tubings, allowing the determination of (Rachoin and Weisberg, 2019) the highest rates of DEHA able to migrate into a simulant flowing in a marketed adult CVVH circuit by disregarding any metabolisation and (Krieter et al., 2013) the clinical-reflecting exposure of patients to this plasticizer and its metabolites by assessing their migration into blood. In the first model, we showed that patients undergoing a CVVH procedure may be exposed to high rates of DEHA. Moreover, DEHA is continuously hydrolyzed into its primary metabolite MEHA (monoethylhexyladipate), which may reach cytotoxic level in the patients' blood. When looking from a « safer ¼ MD perspective, DEHA might not be the best alternative plasticizer for CVVH tubings. However, to reflect clinical conditions, this study should be completed by an in-vivo evaluation (biomonitoring) of the oxidized metabolites of DEHA in urines of inpatients undergoing CVVH.

In vitro cytotoxic effects of secondary metabolites of DEHP and its alternative plasticizers DINCH and DINP on a L929 cell line.

BACKGROUND: Phthalic acid esters are widely used to improve the plasticity of PVC in medical devices (MD). The most famous plasticizer is DEHP, whose use in medical devices has been contested by the European authorities since 2008. Several alternative plasticizers are being considered to replace DEHP, such as DEHT, TOTM, DINP or DINCH, but they are also released from the PVC throughout their life cycle and are metabolized in the same way as DEHP. OBJECTIVES: Our study focuses on the in vitro cytotoxicity of two alternative plasticizers (DINCH and DINP) contained in certain medical devices. They are likely to migrate and be transformed in vivo into the primary and secondary metabolites by a metabolism similar to that of DEHP. This preliminary study is the first to assess the in vitro cytotoxicity of oxidized metabolites of DINCH and DINP based on the EN ISO 10-993-5 standards documents. METHODS: We have studied the complete multi-step organic synthesis of secondary metabolites of DINP and DINCH and have performed cytotoxicity tests on L929 murine cells according to the EN ISO 10993-5 standard design for the biocompatibility of a MD. The tested concentrations of obtained metabolites (0.01, 0.05 and 0.1 mg/mL) covered the range likely to be found for DEHP (total metabolism) in biological fluids coming into direct contact with the MD. The concentrations tested in our study were chosen based on a complete transformation of the plasticizers released after direct contact between a MD and the patient's blood. RESULTS: Only 7-oxo-MMeOCH is cytotoxic at the highest concentration (0.1 mg/mL) after 7 days of exposure, just like 5-oxo-MEHP for the same concentration. By contrast, 7-OH-MMeOP, 7-cx-MMeOP, 7-oxo-MMeOP, 7-OH-MMeOCH and 7-cx-MMeOCH were not found to be cytotoxic. CONCLUSION: The known concentrations of these secondary metabolites in urinary samples are in the µg/L range, i.e. about 100-1000 times lower than the concentrations tested in this study. Cytotoxicity is known to be dose-dependent but it is not always the case for endocrine perturbations and the secondary metabolites could induce endocrine perturbations at very low doses.

New SPE-LC-MS/MS method for the simultaneous determination in urine of 22 metabolites of DEHP and alternative plasticizers from PVC medical devices.

DiEthylHexylPhthalate (DEHP) can leach out of plasticized PVC medical devices (MD) and may enter into contact with patients. This phthalate is known for its reprotoxic and endocrine disrupting effects. Its use in medical devices (MD) has been restricted and alternative plasticizers have been developed. Nevertheless, no published clinical studies exist concerning patient exposure to these alternative plasticizers during medical care. This is particularly worrisome when high-risk populations, such as newborns, are exposed to these new plasticizers in intensive care units. Our study aimed to develop a novel sensitive and selective method to simultaneously identify and quantify DEHP and 17 other plasticizer metabolites (free or glucuronide conjugates), which are specific biomarkers of DEHTP, TOTM, DINP, DINCH and DEHA exposure in human urine. This robust method uses turbulent-flow online extraction technology coupled to high performance liquid chromatography - tandem mass spectrometry. Special care was taken to address two major problems in plasticizer analysis: contamination and chromatographic separation of interfering analogue structures. The validation was assessed in synthetic urine and the linearity of response was demonstrated for all compounds (R2 > 0.99), with limits of quantification from 0.01 to 0.1 ng/ml. Accuracies ranged from 86% to 117% and inter- and intra-day precisions were <20%. The clinical applicability and suitability of our new method was assessed in patients in a neonatal intensive care unit to measure urinary concentrations of DEHP and alternative plasticizer metabolites. These metabolites were found in the majority of urine samples, with a median detection frequency of 95.2% (ranging from 12.5% to 100%). The high sensitivity, selectivity and ruggedness make the method suitable for large-scale biomonitoring studies of high-risk and general populations.

Patients' exposure to PVC plasticizers from ECMO circuits.

BACKGROUND: ECMO is a therapeutic act with a high risk of exposure to diethylhexylphthalate (DEHP), plasticizer from PVC tubings. The replacement of this plasticizer with alternative compounds is recommended but the risks associated with the use of new plasticizers have not been evaluated in ECMO situations. METHODS: Ex vivo ECMO models were performed with different flow rates over 6 days to evaluate the migration of plasticizers and their potential toxic risk for patient. The release of plasticizers during ECMO was measured and compared to reference value (derived no effect level, DNEL) and to cytotoxic concentration carried out with MTT test. RESULTS: Trioctyltrimellitate (TOTM), main plasticizer present in circuit (44% w/w), is weakly released during ECMO. Concentrations are not cytotoxic and exposure doses are lower than DNEL. In contrast, DEHP doses are higher than the DNEL despite a lower presence of DEHP in the circuit (0.2%). We have shown that DEHP is not coming from the circuit but from the priming bag. Replacing this bag with a multilayer one avoids the exposure to DEHP. CONCLUSION: Our study shows that circuits made of PVC plasticized with TOTM against DEHP improves the safety of ECMO.

Effects of flow rate on the migration of different plasticizers from PVC infusion medical devices.

Infusion medical devices (MDs) used in hospitals are often made of plasticized polyvinylchloride (PVC). These plasticizers may leach out into infused solutions during clinical practice, especially during risk-situations, e.g multiple infusions in Intensive Care Units and thus may enter into contact with the patients. The migrability of the plasticizers is dependent of several clinical parameters such as temperature, contact time, nature of the simulant, etc… However, no data is available about the influence of the flow rate at which drug solutions are administrated. In this study, we evaluated the impact of different flow rates on the release of the different plasticizers during an infusion procedure in order to assess if they could expose the patients to more toxic amounts of plasticizers. Migration assays with different PVC infusion sets and extension lines were performed with different flow rates that are used in clinical practice during 1h, 2h, 4h, 8h and 24h, using a lipophilic drug simulant. From a clinical point of view, the results showed that, regardless of the plasticizer, the faster the flow rate, the higher the infused volume and the higher the quantities of plasticizers released, both from infusion sets and extension lines, leading to higher patient exposure. However, physically, there was no significant difference of the migration kinetics linked to the flow rate for a same medical device, reflecting complex interactions between the PVC matrix and the simulant. The migration was especially dependent on the nature and the composition of the medical device.

In vitro cytotoxic effects of DEHP-alternative plasticizers and their primary metabolites on a L929 cell line.

Phthalic acid esters have been widely used to improve the plasticity of PVC medical devices. They carry a high exposure risk for both humans and the environment in clinical situations. Our study focuses on the cytotoxicity of alternative plasticizers. Postulated primary metabolites were synthesized, not being commercially available. Cytotoxicity assays were performed on L929 murine cells according to the ISO-EN 10993-5 standard design for the biocompatibility of medical devices. The tested concentrations of plasticizers (0.01, 0.05 and 0.1 mg/ml) covered the range likely to be found in biological fluids coming into direct contact with the medical devices. DEHP, DINP and DINCH were cytotoxic at the highest concentration (0.1 mg/ml) for 7 days of exposure. Their corresponding metabolites were found to be more cytotoxic, for the same concentration. By contrast, TOTM and its corresponding metabolite MOTM were not found to be cytotoxic. DEHA showed no cytotoxicity, but its corresponding monoester (MEHA) produced a cytotoxic effect at 0.05 mg/ml. In clinical situations, medical devices can release plasticizers, which can come into contact with patients. In vivo, the plasticizers are quickly transformed into primary metabolites. It is therefore important to measure the effects of both the plasticizers and their corresponding metabolites. Standard first-line cytotoxicity assays should be performed to ensure biocompatibility.

Analysis of PVC plasticizers in medical devices and infused solutions by GC-MS.

In 2008, di-(2-ethylhexyl) phthalate (DEHP), was categorized as CMR 1B under the CLP regulations and its use in PVC medical devices (MD) was called into question by the European authorities. This resulted in the commercialization of PVC MDs plasticized with the DEHP alternative plasticizers tri-octyl trimellitate (TOTM), di-(2-ethylhexyl) terephthalate (DEHT), di-isononyl cyclohexane-1,2-dicarboxylate (DINCH), di-isononyl phthalate (DINP), di-(2-ethylhexy) adipate (DEHA), and Acetyl tri-n-butyl citrate (ATBC). The data available on the migration of these plasticizers from the MDs are too limited to ensure their safe use. We therefore developed a versatile GC-MS method to identify and quantify both these newly used plasticizers and DEHP in MDs and to assess their migration abilities in simulant solution. The use of cubic calibration curves and the optimization of the analytical method by an experimental plan allowed us to lower the limit of plasticizer quantification. It also allowed wide calibration curves to be established that were adapted to this quantification in MDs during migration tests, irrespective of the amount present, and while maintaining good precision and accuracy. We then tested the developed method on 32 PVC MDs used in our hospital and evaluated the plasticizer release from a PVC MD into a simulant solution during a 24h migration test. The results showed a predominance of TOTM in PVC MDs accompanied by DEHP (<0.1% w/w), DEHT, and sometimes DEHA. The migration tests showed a difference in the migration ability between the plasticizers and a non-linear kinetic release.