Formulation and Aerosol Jet Printing of Nickel Nanoparticle Ink for High-Temperature Microelectronic Applications and Patterned Graphene Growth.

Aerosol jet printing (AJP) is an advanced manufacturing technique for directly writing nanoparticle inks onto target substrates. It is an emerging reliable, efficient, and environmentally friendly fabrication route for thin film electronics and advanced semiconductor packaging. This fabrication technique is highly regarded for its rapid prototyping, the flexibility of design, and fine feature resolution. Nickel is an attractive high-temperature packaging material due to its electrical conductivity, magnetism, and corrosion resistance. In this work, we synthesized nickel nanoparticles and formulated an AJP ink, which was printed on various material surfaces. Thermal sintering experiments were performed on the samples to explore the redox behavior and to optimize the electrical performance of the devices. The nickel devices were heated to failure under an argon atmosphere, which was marked by a loss of reflectance and electrical properties due to the dewetting of the films. Additionally, a reduction mechanism was observed from these studies, which resembled that of nucleation and coalescence. Finally, multilayer graphene was grown on a custom-printed nickel thin film using chemical vapor deposition (CVD), establishing a fully additive manufacturing route to patterned graphene.

Nozzle-Free Printing of CNT Electronics Using Laser-Generated Focused Ultrasound.

Printed electronics have made remarkable progress in recent years and inkjet printing (IJP) has emerged as one of the leading methods for fabricating printed electronic devices. However, challenges such as nozzle clogging, and strict ink formulation constraints have limited their widespread use. To address this issue, a novel nozzle-free printing technology is explored, which is enabled by laser-generated focused ultrasound, as a potential alternative printing modality called Shock-wave Jet Printing (SJP). Specifically, the performance of SJP-printed and IJP-printed bottom-gated carbon nanotube (CNT) thin film transistors (TFTs) is compared. While IJP required ten print passes to achieve fully functional devices with channel dimensions ranging from tens to hundreds of micrometers, SJP achieved comparable performance with just a single pass. For optimized devices, SJP demonstrated six times higher maximum mobility than IJP-printed devices. Furthermore, the advantages of nozzle-free printing are evident, as SJP successfully printed stored and unsonicated inks, delivering moderate electrical performance, whereas IJP suffered from nozzle clogging due to CNT agglomeration. Moreover, SJP can print significantly longer CNTs, spanning the entire range of tube lengths of commercially available CNT ink. The findings from this study contribute to the advancement of nanomaterial printing, ink formulation, and the development of cost-effective printable electronics.

Multijet Gold Nanoparticle Inks for Additive Manufacturing of Printed and Wearable Electronics.

Conductive and biofriendly gold nanomaterial inks are highly desirable for printed electronics, biosensors, wearable electronics, and electrochemical sensor applications. Here, we demonstrate the scalable synthesis of stable gold nanoparticle inks with low-temperature sintering using simple chemical processing steps. Multiprinter compatible aqueous gold nanomaterial inks were formulated, achieving resistivity as low as ∼10-6 Ω m for 400 nm thick films sintered at 250 °C. Printed lines with a resolution of <20 µm and minimal overspray were obtained using an aerosol jet printer. The resistivity of the printed patterns reached ∼9.59 ± 1.2 × 10-8 Ω m after sintering at 400 °C for 45 min. Our aqueous-formulated gold nanomaterial inks are also compatible with inkjet printing, extending the design space and manufacturability of printed and flexible electronics where metal work functions and chemically inert films are important for device applications.

Analysis of Near-Wall Pebble Bed Thermal Conductivity for Energy Applications.

Pebble beds have been employed in thermal storage and energy systems, where they are typically used to promote heat exchange in high-temperature environments. Understanding the heat conduction of the entire pebble bed could aid in the material selection of the pebbles themselves and structural components, system design, and safety monitoring. However, the thermal conductivity of pebble beds can change significantly near geometric boundaries. Using a complex multilayer analytical model in conjunction with a line source probe, we found a substantial increase in the thermal conductivity of a sintered bauxite pebble bed in the near-wall region (7.6 W m-1 K-1) compared to the bulk (0.59 W m-1 K-1). We investigated this difference by comparing porosity results, acquired with micro-CT, of 33.18 and 33.31% at approximately one pebble width surrounding the probe (near-wall) and the bulk of the pebble bed, suggesting that the thermal conductivity is largely altered by thermal contact resistance in the near-wall regime.

Correlative Imaging of Three-Dimensional Cell Culture on Opaque Bioscaffolds for Tissue Engineering Applications.

Three-dimensional (3D) tissue engineering (TE) is a prospective treatment that can be used to restore or replace damaged musculoskeletal tissues, such as articular cartilage. However, current challenges in TE include identifying materials that are biocompatible and have properties that closely match the mechanical properties and cellular microenvironment of the target tissue. Visualization and analysis of potential 3D porous scaffolds as well as the associated cell growth and proliferation characteristics present additional problems. This is particularly challenging for opaque scaffolds using standard optical imaging techniques. Here, we use graphene foam (GF) as a 3D porous biocompatible substrate, which is scalable, reproducible, and a suitable environment for ATDC5 cell growth and chondrogenic differentiation. ATDC5 cells are cultured, maintained, and stained with a combination of fluorophores and gold nanoparticles to enable correlative microscopic characterization techniques, which elucidate the effect of GF properties on cell behavior in a 3D environment. Most importantly, the staining protocol allows for direct imaging of cell growth and proliferation on opaque scaffolds using X-ray MicroCT, including imaging growth of cells within the hollow GF branches, which is not possible with standard fluorescence and electron microscopy techniques.

Aerosol jet printing of piezoelectric surface acoustic wave thermometer.

Surface acoustic wave (SAW) devices are a subclass of micro-electromechanical systems (MEMS) that generate an acoustic emission when electrically stimulated. These transducers also work as detectors, converting surface strain into readable electrical signals. Physical properties of the generated SAW are material dependent and influenced by external factors like temperature. By monitoring temperature-dependent scattering parameters a SAW device can function as a thermometer to elucidate substrate temperature. Traditional fabrication of SAW sensors requires labor- and cost- intensive subtractive processes that produce large volumes of hazardous waste. This study utilizes an innovative aerosol jet printer to directly write consistent, high-resolution, silver comb electrodes onto a Y-cut LiNbO3 substrate. The printed, two-port, 20 MHz SAW sensor exhibited excellent linearity and repeatability while being verified as a thermometer from 25 to 200 ∘C. Sensitivities of the printed SAW thermometer are - 96.9 × 1 0 - 6 ∘ C-1 and - 92.0 × 1 0 - 6 ∘ C-1 when operating in pulse-echo mode and pulse-receiver mode, respectively. These results highlight a repeatable path to the additive fabrication of compact high-frequency SAW thermometers.

Structure-Property-Processing Correlations of Graphene Bioscaffolds for Proliferation and Differentiation of C2C12 Cells.

Graphene - an atomically thin layer of carbon atoms arranged in a hexagonal lattice - has gained interest as a bioscaffold for tissue engineering due to its exceptional mechanical, electrical, and thermal properties. Graphene's structure and properties are tightly coupled to synthesis and processing conditions, yet their influence on biomolecular interactions at the graphene-cell interface remains unclear. In this study, C2C12 cells were grown on graphene bioscaffolds with specific structure-property- processing-performance (SP3) correlations. Bioscaffolds were prepared using three different methods - chemical vapor deposition (CVD), sublimation of silicon carbide (SiC), and printing of liquid phase exfoliated graphene. To investigate the biocompatibility of each scaffold, cellular morphology and gene expression patterns were investigated using the bipotential mouse C2C12 cell line. Using a combination of fluorescence microscopy and qRT-PCR, we demonstrate that graphene production methods determine the structural and mechanical properties of the resulting bioscaffold, which in turn determine cell morphology, gene expression patterns, and cell differentiation fate. Therefore, production methods and resultant structure and properties of graphene bioscaffolds must be chosen carefully when considering graphene as a bioscaffold for musculoskeletal tissue engineering.

Correlative Imaging of 3D Cell Culture on Opaque Bioscaffolds for Tissue Engineering Applications.

Three-dimensional (3D) tissue engineering (TE) is a prospective treatment that can be used to restore or replace damaged musculoskeletal tissues such as articular cartilage. However, current challenges in TE include identifying materials that are biocompatible and have properties that closely match the mechanical properties and cellular environment of the target tissue, while allowing for 3D tomography of porous scaffolds as well as their cell growth and proliferation characterization. This is particularly challenging for opaque scaffolds. Here we use graphene foam (GF) as a 3D porous biocompatible substrate which is scalable, reproduceable, and a suitable environment for ATDC5 cell growth and chondrogenic differentiation. ATDC5 cells are cultured, maintained, and stained with a combination of fluorophores and gold nanoparticle to enable correlative microscopic characterization techniques, which elucidate the effect of GF properties on cell behavior in a three-dimensional environment. Most importantly, our staining protocols allows for direct imaging of cell growth and proliferation on opaque GF scaffolds using X-ray MicroCT, including imaging growth of cells within the hollow GF branches which is not possible with standard fluorescence and electron microscopy techniques.

Plasma-jet printing of colloidal thermoelectric Bi2Te3 nanoflakes for flexible energy harvesting.

Thermoelectric generators (TEGs) convert temperature differences into electrical power and are attractive among energy harvesting devices due to their autonomous and silent operation. While thermoelectric materials have undergone substantial improvements in material properties, a reliable and cost-effective fabrication method suitable for microgravity and space applications remains a challenge, particularly as commercial space flight and extended crewed space missions increase in frequency. This paper demonstrates the use of plasma-jet printing (PJP), a gravity-independent, electromagnetic field-assisted printing technology, to deposit colloidal thermoelectric nanoflakes with engineered nanopores onto flexible substrates at room temperature. We observe substantial improvements in material adhesion and flexibility with less than 2% and 11% variation in performance after 10 000 bending cycles over 25 mm and 8 mm radii of curvature, respectively, as compared to previously reported TE films. Our printed films demonstrate electrical conductivity of 2.5 × 103 S m-1 and a power factor of 70 µW m-1 K-2 at room temperature. To our knowledge, these are the first reported values of plasma-jet printed thermoelectric nanomaterial films. This advancement in plasma jet printing significantly promotes the development of nanoengineered 2D and layered materials not only for energy harvesting but also for the development of large-scale flexible electronics and sensors for both space and commercial applications.

Zinc-Acetate-Amine Complexes as Precursors to ZnO and the Effect of the Amine on Nanoparticle Morphology, Size, and Photocatalytic Activity.

Zinc oxide is an environmentally friendly and readily synthesized semiconductor with many industrial applications. ZnO powders were prepared by alkali precipitation using different [Zn(acetate)2(amine)x] compounds to alter the particle size and aspect ratio. Slow precipitations from 95 °C solutions produced micron-scale particles with morphologies of hexagonal plates, rods, and needles, depending on the precursor used. Powders prepared at 65 °C with rapid precipitation yielded particles with minimal morphology differences, but particle size was dependent on the precursor used. The smallest particles were produced using precursors that yielded crystals with low aspect ratios during high-temperature synthesis. Particles produced during rapid synthesis had sizes ranging from 21-45 nm. The materials were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, thermogravimetric analysis, BET, and diffuse reflectance. The materials prepared using precursors with less-volatile amines were found to retain more organic material than ZnO produced using precursors with more volatile amines. The amount of organic material associated with the nanoparticles influenced the photocatalytic activity of the ZnO, with powders containing less organic material producing faster rate constants for the decolorizing of malachite green solutions under ultraviolet illumination, independent of particle size. [Zn(acetate)2(hydrazine)2] produced ZnO with the fastest rate constant and was recycled five times for dye degradation studies that revealed minimal to no reduction in catalytic efficiency.

Lung ultrasound as a screening tool for SARS-CoV-2 infection in surgical patients.

PURPOSE: To evaluate the diagnostic performance of lung ultrasound (LUS) in screening for SARS-CoV-2 infection in patients requiring surgery. METHODS: Patients underwent a LUS protocol that included a scoring system for screening COVID-19 pneumonia as well as RT-PCR test for SARS-CoV-2. The receiver operator characteristic (ROC) curve was determined for the relationship between LUS score and PCR test results for COVID-19. The optimal threshold for the best discrimination between non-COVID-19 patients and COVID-19 patients was calculated. RESULTS: Among 203 patients enrolled (mean age 48 years; 82 males), 8.3% were COVID-19-positive; 4.9% were diagnosed via the initial RT-PCR test. Of the patients diagnosed with SARS-CoV-2, 64.7% required in-hospital management and 17.6% died. The most common ultrasound findings were B lines (19.7%) and a thickened pleura (19.2%). The AUC of the ROC curve of the relationship of LUS score with a cutoff value >8 versus RT-PCR test for the assessment of SARS-CoV-2 pneumonia was 0.75 (95% CI 0.61-0.89; sensitivity 52.9%; specificity 91%; LR (+) 6.15, LR (-) 0.51). CONCLUSION: The LUS score in surgical patients is not a useful tool for screening patients with potential COVID-19 infection. LUS score shows a high specificity with a cut-off value of 8.

Synergic Antitumor Effect of Photodynamic Therapy and Chemotherapy Mediated by Nano Drug Delivery Systems.

This review provides a summary of recent progress in the development of different nano-platforms for the efficient synergistic effect between photodynamic therapy and chemotherapy. In particular, this review focuses on various methods in which photosensitizers and chemotherapeutic agents are co-delivered to the targeted tumor site. In many cases, the photosensitizers act as drug carriers, but this review, also covers different types of appropriate nanocarriers that aid in the delivery of photosensitizers to the tumor site. These nanocarriers include transition metal, silica and graphene-based materials, liposomes, dendrimers, polymers, metal-organic frameworks, nano emulsions, and biologically derived nanocarriers. Many studies have demonstrated various benefits from using these nanocarriers including enhanced water solubility, stability, longer circulation times, and higher accumulation of therapeutic agents/photosensitizers at tumor sites. This review also describes novel approaches from different research groups that utilize various targeting strategies to increase treatment efficacy through simultaneous photodynamic therapy and chemotherapy.

Utilization of Complementary and Integrative Health Care by People With Spinal Cord Injury in the Spinal Cord Injury Model Systems: A Descriptive Study.

OBJECTIVE: To characterize the use of complementary and integrative health care (CIH) by people with spinal cord injury. DESIGN: Cross-sectional self-report study. SETTING: Participants were recruited from 5 Spinal Cord Injury Model Systems (SCIMS) centers across the United States. INTERVENTIONS: Not applicable. PARTICIPANTS: A total of 411 persons enrolled in the SCIMS completing their SCIMS follow-up interview between January 2017 and July 2019 (N = 411). MAIN OUTCOME MEASURES: Participants completed a survey developed for this study that included questions about types of CIH currently and previously used, reasons for current and previous use, reasons for discontinuing use of CIH, and reasons for never using CIH since injury. RESULTS: Of the 411 respondents, 80.3% were current or previous users of CIH; 19.7% had not used CIH since injury. The most commonly used current types of CIH were multivitamins (40.0%) and massage (32.6%), whereas the most common previously used type of CIH was acupuncture (33.9%). General health and wellness (61.4%) and pain (31.2%) were the most common reasons for using CIH. The primary reason for discontinuing CIH was that it was not helpful (42.1%). The primary reason for not using CIH since injury was not knowing what options are available (40.7%). CONCLUSIONS: These results point to the importance for rehabilitation clinicians to be aware that their patients may be using 1 or more CIH approaches. Providers should be open to starting a dialogue to ensure the health and safety of their patients because there is limited information on safety and efficacy of CIH approaches in this population. These results also set the stage for further analysis of this data set to increase our knowledge in this area.

Additive Manufacturing of Miniaturized Peak Temperature Monitors for In-Pile Applications.

Passive monitoring techniques have been used for peak temperature measurements during irradiation tests by exploiting the melting point of well-characterized materials. Recent efforts to expand the capabilities of such peak temperature detection instrumentation include the development and testing of additively manufactured (AM) melt wires. In an effort to demonstrate and benchmark the performance and reliability of AM melt wires, we conducted a study to compare prototypical standard melt wires to an AM melt wire capsule, composed of printed aluminum, zinc, and tin melt wires. The lowest melting-point material used was Sn, with a melting point of approximately 230 °C, Zn melts at approximately 420 °C, and the high melting-point material was aluminum, with an approximate melting point of 660 °C. Through differential scanning calorimetry and furnace testing we show that the performance of our AM melt wire capsule was consistent with that of the standard melt-wire capsule, highlighting a path towards miniaturized peak-temperature sensors for in-pile sensor applications.

A Review of Inkjet Printed Graphene and Carbon Nanotubes Based Gas Sensors.

Graphene and carbon nanotube (CNT)-based gas/vapor sensors have gained much traction for numerous applications over the last decade due to their excellent sensing performance at ambient conditions. Inkjet printing various forms of graphene (reduced graphene oxide or modified graphene) and CNT (single-wall nanotubes (SWNTs) or multiwall nanotubes (MWNTs)) nanomaterials allows fabrication onto flexible substrates which enable gas sensing applications in flexible electronics. This review focuses on their recent developments and provides an overview of the state-of-the-art in inkjet printing of graphene and CNT based sensors targeting gases, such as NO2, Cl2, CO2, NH3, and organic vapors. Moreover, this review presents the current enhancements and challenges of printing CNT and graphene-based gas/vapor sensors, the role of defects, and advanced printing techniques using these nanomaterials, while highlighting challenges in reliability and reproducibility. The future potential and outlook of this rapidly growing research are analyzed as well.

Center of Biomedical Research Excellence in Matrix Biology: Building Research Infrastructure, Supporting Young Researchers, and Fostering Collaboration.

The Center of Biomedical Research Excellence in Matrix Biology strives to improve our understanding of extracellular matrix at molecular, cellular, tissue, and organismal levels to generate new knowledge about pathophysiology, normal development, and regenerative medicine. The primary goals of the Center are to i) support junior investigators, ii) enhance the productivity of established scientists, iii) facilitate collaboration between both junior and established researchers, and iv) build biomedical research infrastructure that will support research relevant to cell-matrix interactions in disease progression, tissue repair and regeneration, and v) provide access to instrumentation and technical support. A Pilot Project program provides funding to investigators who propose applying their expertise to matrix biology questions. Support from the National Institute of General Medical Sciences at the National Institutes of Health that established the Center of Biomedical Research Excellence in Matrix Biology has significantly enhanced the infrastructure and the capabilities of researchers at Boise State University, leading to new approaches that address disease diagnosis, prevention, and treatment. New multidisciplinary collaborations have been formed with investigators who may not have previously considered how their biomedical research programs addressed fundamental and applied questions involving the extracellular matrix. Collaborations with the broader matrix biology community are encouraged.

Recurrent Pneumonias in a Previously Healthy and Immunocompetent Young Adult: A Case Report Mounier-Kuhn Syndrome.

BACKGROUND Mounier-Kuhn syndrome is a rare clinical condition characterized by marked tracheal and bronchial dilatation. It is commonly associated with multiple respiratory infections due to the inability to mobilize secretions, chronic cough, and decline in lung capacity. Although it is a rare disease, the number of cases reported in the literature has increased, and physicians should be aware of its existence to be able to recognize and diagnose it. Suspicion should arise regarding young adults who develop recurrent airway infections when immunosuppression has been ruled out. CASE REPORT We present the case of a young adult, previously healthy and immunocompetent, who was diagnosed with Mounier-Kuhn syndrome after 5 years of multiple respiratory infections and multiple respiratory failures, who received intensive care management with multiple complications and difficulties in achieving adequate ventilation. Due to the risk of respiratory failure and major complications, its management was challenging. We were able to treat this patient and prevent complications with a multidisciplinary approach with a strong emphasis on constant and intense pulmonary therapy. CONCLUSIONS Mounier-Kuhn syndrome is rare but does occur, and physicians need to have a high index of suspicion to diagnose it. Its management must be done by a multidisciplinary team, and respiratory therapy should be constantly available at bedside.

Fully inkjet-printed multilayered graphene-based flexible electrodes for repeatable electrochemical response.

Graphene has proven to be useful in biosensing applications. However, one of the main hurdles with printed graphene-based electrodes is achieving repeatable electrochemical performance from one printed electrode to another. We have developed a consistent fabrication process to control the sheet resistance of inkjet-printed graphene electrodes, thereby accomplishing repeatable electrochemical performance. Herein, we investigated the electrochemical properties of multilayered graphene (MLG) electrodes fully inkjet-printed (IJP) on flexible Kapton substrates. The electrodes were fabricated by inkjet printing three materials - (1) a conductive silver ink for electrical contact, (2) an insulating dielectric ink, and (3) MLG ink as the sensing material. The selected materials and fabrication methods provided great control over the ink rheology and material deposition, which enabled stable and repeatable electrochemical response: bending tests revealed the electrochemical behavior of these sensors remained consistent over 1000 bend cycles. Due to the abundance of structural defects (e.g., edge defects) present in the exfoliated graphene platelets, cyclic voltammetry (CV) of the graphene electrodes showed good electron transfer (k = 1.125 × 10-2 cm s-1) with a detection limit (0.01 mM) for the ferric/ferrocyanide redox couple, [Fe(CN)6]-3/-4, which is comparable or superior to modified graphene or graphene oxide-based sensors. Additionally, the potentiometric response of the electrodes displayed good sensitivity over the pH range of 4-10. Moreover, a fully IJP three-electrode device (MLG, platinum, and Ag/AgCl) also showed quasi-reversibility compared to a single IJP MLG electrode device. These findings demonstrate significant promise for scalable fabrication of a flexible, low cost, and fully-IJP wearable sensor system needed for space, military, and commercial biosensing applications.

The Thinnest of Materials May Hold a Cure for Osteoarthritis.

Since the turn of the century, a myriad of exciting applications for graphene have emerged. Amongst the most exciting might be its use as a scaffold for promoting tissue growth in the treatment of various medical conditions, including osteoarthritis. Researchers at Boise State University in the USA and Carl von Ossietzky University of Oldenburg in Germany are gaining a greater understanding of the interactions between graphene and cells, towards the development of implantable graphene-based devices that can rebuild damaged tissue.

High-Performance Flexible Bismuth Telluride Thin Film from Solution Processed Colloidal Nanoplates.

Thermoelectric generators are an environmentally friendly and reliable solid-state energy conversion technology. Flexible and low-cost thermoelectric generators are especially suited to power flexible electronics and sensors using body heat or other ambient heat sources. Bismuth telluride based thermoelectric materials exhibit their best performance near room temperature making them an ideal candidate to power wearable electronics and sensors using body heat. In this report Bi2Te3 thin films are deposited on a flexible polyimide substrate using low-cost and scalable manufacturing methods. The synthesized Bi2Te3 nanocrystals have a thickness of 35 ± 15 nm and a lateral dimension of 692 ± 186 nm. Thin films fabricated from these nanocrystals exhibit a peak power factor of 0.35 mW/m·K2 at 433 K, which is among the highest reported values for flexible thermoelectric films. In order to evaluate the flexibility of the thin films, static and dynamic bending tests were performed while monitoring the change in electrical resistivity. After 1000 bending cycles over a 50mm ROC, the change in electrical resistance of the film was 23%. Using our Bi2Te3 solutions, we demonstrated the ability to print thermoelectric thin films with an aerosol jet printer, highlighting the potential of additive manufacturing techniques for fabricating flexible thermoelectric generators.