Investigations of a 1018 nm gain-switched Yb-doped fiber oscillator.

In this paper, we investigate a 1018 nm gain-switched ytterbium-doped fiber oscillator at a low repetition rate in terms of theory and experiment. Theoretically, a numerical model applicable to a 1018 nm gain-switched ytterbium-doped fiber laser was established. The influence of the pump peak power and active fiber lengths on the 1018 nm gain-switched ytterbium-doped fiber laser was numerically simulated. Experimentally, a compact 1018 nm all-fiber-structured pulsed laser oscillator is constructed, in which a pulse width of 110 ns and a single-pulse energy of 0.1 mJ were obtained. Moreover, the experimental results are in agreement with the numerical simulation ones. To the best of our knowledge, this is the first time that gain-switching technology has been applied to 1018 nm fiber lasers to generate nanosecond pulsed lasers. The model and experimental results can provide a reference for the engineering design of the same type of low repetition rate fiber lasers below the kilohertz level.

Ultrahigh Energy Storage Density and Efficiency in Orthorhombic PLZST Antiferroelectric Ceramics via Composition Regulation.

PbZrO3-based antiferroelectric (AFE) ceramic materials have emerged as potential candidates for the next generation of high-energy multilayer ceramic capacitors (MLCCs) because of their distinctive characteristics of double hysteresis loops. The energy storage efficiency of orthorhombic AFE ceramics with ultrahigh storage density is relatively low, which hinders their practical application. In this study, the low efficiency limit of PLZST-based orthorhombic ceramics was overcome by precisely adjusting the Sn4+ content in the (Pb0.95Ca0.02La0.02)(Zr0.99-xSnxTi0.01)O3 AFE ceramics. On one hand, the addition of Sn4+ disrupts the original long-range dipole and improves the rapid response of polarization reversal under the applied voltage. As a result, the difference in electric hysteresis under an electric field is reduced, leading to a significant improvement in energy storage efficiency. On the other hand, increasing the Sn4+ content suppresses the formation of oxygen vacancies, inhibiting grain growth and strengthening grain bonding. This results in ceramics with a high breakdown field strength. Ultimately, the resulting PLCZST ceramics reveal an expressively improved recoverable energy density of 10.2 J cm-3 together with a high energy efficiency of 91.4% under a high applied electric field of 560 kV cm-1. The present study demonstrates the tunability of performance in orthorhombic PLZST AFE ceramics, thereby introducing a ceramic material with exceptional energy storage capabilities for MLCC applications.

Self-Assembling Anti-Freezing Lamellar Nanostructures in Subzero Temperatures.

The requirement for cryogenic supramolecular self-assembly of amphiphiles in subzero environments is a challenging topic. Here, the self-assembly of lamellar lyotropic liquid crystals (LLCs) are presented to a subzero temperature of -70 °C. These lamellar nanostructures are assembled from specifically tailored ultra-long-chain surfactant stearyl diethanolamine (SDA) in water/glycerol binary solvent. As the temperature falls below zero, LLCs with a liquid-crystalline Lα phase, a tilted Lß phase, and a new folded configuration are obtained consecutively. A comprehensive experimental and computational study is performed to uncover the precise microstructure and formation mechanism. Both the ultra-long alkyl chain and head group of SDA play a crucial role in the formation of lamellar nanostructures. SDA head group is prone to forming hydrogen bonds with water, rather than glycerol. Glycerol cannot penetrate the lipid layer, which mixes with water arranging outside of the lipid bilayer, providing an ideal anti-freezing environment for SDA self-assembly. Based on these nanostructures and the ultra-low freezing point of the system, a series of novel cryogenic materials are created with potential applications in extremely cold environments. These findings would contribute to enriching the theory and research methodology of supramolecular self-assembly in extreme conditions and to developing novel anti-freezing materials.

All-fiber hectowatt radially polarized laser system.

A high-power all-fiber radially polarized laser system is demonstrated, in which an integrated nanograting mode convertor (S-wave plate) is used for the generation of radially polarized beam. Experimentally, a 1-W radially polarized beam was used as the seed laser, whose mode purity and mode extinction ratio (MER) were 96.5% and 98.3%, respectively. A single-stage few-mode fiber amplifier was employed to boost the 1-W seed laser to an average power of 113.2 W, when the pump power was 160 W. The corresponding slope efficiency and beam quality factor (M2) were approximately 72% and 2.3%, respectively. Moreover, the mode purity and MER of the amplified radially polarized laser were measured to be 95.7% and 97%, respectively. To the best of our knowledge, this is the highest output power from an all-fiber radially polarized laser system without obvious degradations of the mode purity and MER.

Effects of exogenous steroid hormones on growth, body color, and gonadal development in the Opsariichthys bidens.

To investigate the effects of exogenous steroid hormones on growth, body color, and gonadal development in the Opsariichthys bidens (O. bidens), synthetic methyltestosterone (MT) and 17ß-estradiol (E2) were used for 28 days' treatment of 4-month-old O. bidens before the breeding season. Our results suggested that MT had a significant growth-promoting effect (P < 0.05), whereas E2 played an inhibitory role. On the body surface, the females in the MT group showed gray stripes, and the fish in other groups showed no obvious stripes. The males with MT treatment displayed brighter blue-green stripes compared to the CK and E2 groups. The histological analysis showed that the MT significantly promoted testes development in males, blocked oocyte development, and caused massive apoptosis in females, whereas the E2 group promoted ovarian development and inhibited testes development. Based on qRT-PCR analysis, in females, the expression of igf-1, dmrt1, and cyp19a1a genes revealed that E2 treatment resulted in down-regulation of igf-1 expression and up-regulation of cyp19a1a expression. In males, igf-1 and dmrt1 were significantly up-regulated after MT treatment, and E2 treatment led to down-regulation of igf-1. Therefore, this study demonstrates that MT and E2 play an important role in reversing the morphological sex characteristics of females and males.

Nonlinear spectral compression in high-power narrow-linewidth polarization maintaining fiber amplifiers for SBS suppression.

In this paper, we propose a method for narrowing the spectrum in high-power narrow-linewidth polarization-maintaining (PM) fiber amplifiers and investigate its potential for suppressing the stimulated Brillouin scattering (SBS). In this method, in addition to common phase modulation to suppress SBS, precisely designed amplitude modulation is induced to generate self-phase modulation in a high-power PM fiber amplifier. In this co-modulation way, the spectrum can be gradually compressed along the fiber. Compared to phase modulation alone or fiber-Bragg-gratings (FBGs) based narrow-linewidth fiber oscillator schemes, in which the spectrum remains the same or broadens, this scheme can achieve a higher SBS threshold for the same output spectral linewidth. Experiments on a ∼ 3 kW peak power quasi-continuous wave (QCW) fiber amplifier show that the co-modulation scheme can compress the spectrum from 0.25 nm to 0.084 nm as output peak power increases from 13 W to 3.2 kW and enhances the SBS threshold by ∼1.7 times compared to traditional FBGs-based fiber oscillator schemes, and by ∼1.4 times compared to common phase modulation schemes. This co-modulation scheme has the potential for mitigating SBS in high-power fiber amplifiers.

Coherent beam combining of cylindrical vector beams for power scaling.

Coherent beam combining (CBC) of cylindrical vector beams (CVBs) based on an active phase controller is proposed and demonstrated. Experimentally, two pieces of spatially variant wave plates (S-wave plate) were employed as vector mode convertors for two individual 1064-nm fiber amplifier channels. When the system was in a closed loop, a combined output power of 10 W and a CBC efficiency of higher than 94% were achieved, for both TM01 (radially polarized) mode and TE01 (azimuthally polarized) mode cases. Moreover, the laser system showed a high vector mode purity, which was measured to be ∼97.4% (TM01) and ∼97.3% (TE01). To the best of knowledge, this could possibly be the first demonstration of CBC of CVBs, which paves the way for power scaling of CVBs.

Leveraging intracellular ALDH1A1 activity for selective cancer stem-like cell labeling and targeted treatment via in vivo click reaction.

Inhibition of overexpressed enzymes is among the most promising approaches for targeted cancer treatment. However, many cancer-expressed enzymes are "nonlethal," in that the inhibition of the enzymes' activity is insufficient to kill cancer cells. Conventional antibody-based therapeutics can mediate efficient treatment by targeting extracellular nonlethal targets but can hardly target intracellular enzymes. Herein, we report a cancer targeting and treatment strategy to utilize intracellular nonlethal enzymes through a combination of selective cancer stem-like cell (CSC) labeling and Click chemistry-mediated drug delivery. A de novo designed compound, AAMCHO [N-(3,4,6-triacetyl- N-azidoacetylmannosamine)-cis-2-ethyl-3-formylacrylamideglycoside], selectively labeled cancer CSCs in vitro and in vivo through enzymatic oxidation by intracellular aldehyde dehydrogenase 1A1. Notably, azide labeling is more efficient in identifying tumorigenic cell populations than endogenous markers such as CD44. A dibenzocyclooctyne (DBCO)-toxin conjugate, DBCO-MMAE (Monomethylauristatin E), could next target the labeled CSCs in vivo via bioorthogonal Click reaction to achieve excellent anticancer efficacy against a series of tumor models, including orthotopic xenograft, drug-resistant tumor, and lung metastasis with low toxicity. A 5/7 complete remission was observed after single-cycle treatment of an advanced triple-negative breast cancer xenograft (~500 mm3).

Linearly polarized fiber amplifier with narrow linewidth of 5†kW exhibiting a record output power and near-diffraction-limited beam quality.

In this work, a narrow-linewidth polarization-maintaining (PM) all-fiber amplifier with near-diffraction-limited beam quality and record output power is presented. First, a 4.45-kW PM fiber amplifier with a 3-dB linewidth of 0.08 nm and root mean square (rms) linewidth of 0.22 nm is achieved based on optimized phase modulation. However, the sideband of the spectrum broadens significantly during the amplification process, which is mainly caused by the additional intensity variation of the injected signal. Meanwhile, an up to 5.04-kW linearly polarized fiber laser with a relatively stable spectral bandwidth is achieved by effectively suppressing spectral broadening. At the maximum output power, the rms linewidth is 0.2 nm, the beam quality factor M2 is less than 1.3, the polarization extinction ratio (PER) is 16.5 dB, and the signal-to-noise ratio (SNR) is approximately 53 dB. The further power scaling of the amplifier is mainly limited by the pump power. To the best of our knowledge, this is the maximum output power of a narrow linewidth linearly polarized fiber amplifier to date.

pH-Responsive Viscoelastic Fluids of a C22-Tailed Surfactant Induced by Trivalent Metal Ions.

pH-responsive viscoelastic fluids are often achieved by adding hydrotropes into surfactant solutions. However, the use of metal salts to prepare pH-responsive viscoelastic fluids has been less documented. Herein, a pH-responsive viscoelastic fluid was developed by blending an ultra-long-chain tertiary amine, N-erucamidopropyl-N, N-dimethylamine (UC22AMPM), with metal salts (i.e., AlCl3, CrCl3, and FeCl3). The effects of the surfactant/metal salt mixing ratio and the type of metal ions on the viscoelasticity and phase behavior of fluids were systematically examined by appearance observation and rheometry. To elucidate the role of metal ions, the rheological properties between AlCl3- and HCl-UC22AMPM systems were compared. Results showed the above metal salt evoked the low-viscosity UC22AMPM dispersions to form viscoelastic solutions. Similar to HCl, AlCl3 could also protonate the UC22AMPM into a cationic surfactant, forming wormlike micelles (WLMs). Notably, much stronger viscoelastic behavior was evidenced in the UC22AMPM-AlCl3 systems because the Al3+ as metal chelators coordinated with WLMs, promoting the increment of viscosity. By tuning the pH, the macroscopic appearance of the UC22AMPM-AlCl3 system switched between transparent solutions and milky dispersion, concomitant with a viscosity variation of one order of magnitude. Importantly, the UC22AMPM-AlCl3 systems showed a constant viscosity of 40 mPa·s at 80 °C and 170 s-1 for 120 min, indicative of good heat and shear resistances. The metal-containing viscoelastic fluids are expected to be good candidates for high-temperature reservoir hydraulic fracturing.

Supramolecular self-assembly of robust, ultra-stable, and high-temperature-resistant viscoelastic worm-like micelles.

HYPOTHESIS: Worm-like micelles are susceptible to heating owing to the fast dynamic exchange of molecules between micelles. Inhibition of such exchange could afford robust worm-like micelles, which is expected to largely improve rheology properties at high temperatures. EXPERIMENTS: A cationic surfactant docosyl(trimethyl)azanium chloride (DCTAC) and a strongly hydrophobic organic counterion 3-hydroxy naphthalene-2-carboxylate (SHNC) were used for the worm-like micelles fabrication. The microstructure was characterized using cryogenic transmission electron microscopy and small-angle neutron scattering, and the interactions between DCTAC and SHNC were characterized using nuclear magnetic resonance spectroscopy. Rheometer was employed to measure the rheological properties of the solution. FINDINGS: SHNC/DCTAC at the molar ration of 1:2 forms ultra-stable worm-like micelles, whose viscosity remain stable at temperature up to 130 °C. SHNC is found to strongly adsorbs on DCTAC micelle with the orientation on the surface of micelle, keeping the naphthalene backbone entire penetration into the palisade layer while both carboxylic and hydroxyl groups protrude out of the micelle. With temperature increasing, this adsorption further strengthens, resulting in the growth contour length and accompanying the enhancement of rheological properties. One SHNC molecule and two DCTAC molecules are speculated to form a stable complex via multiple interactions including hydrophobic, cationic-π, and π-π interactions, which decreases the dynamic exchange of them between micelles. These findings are helpful to understand surfactant aggregates stability and assist the development of novel stable supramolecular nanostructures. Additionally, the excellent thermal stability of this worm-like micellar fluid makes it a potential high-temperature resistant clean fracturing fluid for deep oil reservoirs.

Rock-on-a-chip: "Seeing" the association/disassociation of an adaptive polymer in solutions flowing through porous media.

The flow and transport of polymer solutions through porous media are ubiquitous in myriad scientific and engineering applications. With escalating interest in adaptive polymers, understanding the flow dynamics of their solutions is indispensable (yet lacking). Here, the hydrophobic-effect-driven reversible associations in a self-adaptive polymer (SAP) solution and its flow characteristics in a microfluidic-based "rock-on-a-chip" device have been analyzed. The hydrophobic aggregates were fluorescent labeled; this enabled a direct visualization of the in situ association/disassociation of the polymer supramolecular assemblies in pore spaces and throats. Furthermore, the influence of this adaptation on the macroscopic flow behavior of the SAP solution was analyzed by comparing its flow with that of two partially-hydrolyzed polyacrylamide (the molecular weight (MW)-equivalent HPAM-1 and ultrahigh-MW HPAM-2) solutions in the semi-dilute regime with similar initial viscosities. At low flow rates (with shear predominance), the SAP solution showed a low shear viscosity compared to HPAM-1, indicating a higher shear susceptibility for association than chain entanglement. Although the SAP exhibited the same elastic instability as the non-adaptive polymers above a threshold flow rate, the adaptable structure of the former advanced the onset of its viscoelastic-governed flow, providing a stronger flow resistance, possibly through an extension resistance. Furthermore, 3D-media analysis indicated that the reversible association/disassociation of SAP increased the accessible pore space during nonaqueous-liquid displacement, facilitating oil production.

Screening the Impact of Surfactants and Reaction Conditions on the De-Inkability of Different Printing Ink Systems for Plastic Packaging.

One of the major applications (40% in Europe) of plastic is packaging, which is often printed to display required information and to deliver an attractive aesthetic for marketing purposes. However, printing ink can cause contamination in the mechanical recycling process. To mitigate this issue, the use of surfactants in an alkaline washing process, known as de-inking, has been employed to remove printing ink and improve the quality of recyclates. Despite the existence of this technology, there are currently no data linking the de-inking efficiency with typical printing ink compositions. Additionally, it is necessary to investigate the de-inking process under the process parameters of existing recycling plants, including temperature, NaOH concentration, and retention time. This study aims to evaluate the performance of commonly used printing inks with different compositions under various washing scenarios for plastic recycling in conjunction with different de-inking detergents containing surfactants or mixtures of surfactants. The results indicate that the pigments applied to the ink have no significant effect on the de-inking process, except for carbon black (PBk 7). Nitrocellulose (NC) binder systems exhibit high de-inkability (over 95%) under the condition of 55 °C and 1 wt.% NaOH. However, crosslinked binder systems can impede the de-inking effect, whether used as a binder system or as an overprint varnish (OPV). The de-inking process requires heating to 55 °C with 1 wt.% NaOH to achieve a substantial effect. Based on the findings in this work, breaking the Van der Waals forces, hydrogen bonds, and covalent bonds between the printing ink and plastic film is an essential step to achieve the de-inking effect. Further research is needed to understand the interaction between surfactants and printing inks, enabling the development of de-inkable printing inks and high-performance surfactants that allow for de-inking with less energy consumption. The surfactant and NaOH have a synergistic effect in cleaning the printing ink. NaOH provides a negative surface charge for the adsorption of the cationic head of the surfactant and can hydrolyze the covalent bonds at higher concentrations (>2 wt.%).

A Quantitative Approach to Determine Hydrophobe Content of Associating Polyacrylamide Using a Fluorescent Probe.

Hydrophobically associating polymers have found widespread applications in many domains due to their unique rheological behavior, which is primarily dictated by the hydrophobe content. However, the low fraction of hydrophobic monomers in polymers makes this parameter's precise and straightforward measurement difficult. Herein, a variety of hydrophobically associating polyacrylamides (HAPAM) with different alkyl chain lengths (L) and hydrophobic contents ([H]) were prepared by post-modification and accurately characterized by 1H NMR spectroscopy. The maximal fluorescence emission intensity (I) of 8-anilino-1-naphthalenesulfonic acid, which is sensitive to hydrophobic environments, was then detected in those polymer solutions and shown as a ratio to that in the polymer-free solution (I0). It was found that I/I0 for 0.5 wt% HAPAM can be scaled versus CH, which is a variate related to both L and [H], as I/I0 = 1.15 + 1.09 × 108CH3.42, which was also verified to be applicable for hydrophobic associating hydrolyzed polyacrylamide (HHAPAM). This relationship provides a handy method for determining the hydrophobic content of hydrophobically associating polymers, particularly for field applications.

A Comparative Study on CO2-Switchable Foams Stabilized by C22- or C18-Tailed Tertiary Amines.

The CO2 aqueous foams stabilized by bioresource-derived ultra-long chain surfactants have demonstrated considerable promising application potential owing to their remarkable longevity. Nevertheless, existing research is still inadequate to establish the relationships among surfactant architecture, environmental factors, and foam properties. Herein, two cases of ultra-long chain tertiary amines with different tail lengths, N-erucamidopropyl-N,N-dimethylamine (UC22AMPM) and N-oleicamidopropyl-N,N-dimethylamine (UC18AMPM), were employed to fabricate CO2 foams. The effect of temperature, pressure and salinity on the properties of two foam systems (i.e., foamability and foam stability) was compared using a high-temperature, high-pressure visualization foam meter. The continuous phase viscosity and liquid content for both samples were characterized using rheometry and FoamScan. The results showed that the increased concentrations or pressure enhanced the properties of both foam samples, but the increased scope for UC22AMPM was more pronounced. By contrast, the foam stability for both cases was impaired with increasing salinity or temperature, but the UC18AMPM sample is more sensitive to temperature and salinity, indicating the salt and temperature resistance of UC18AMPM-CO2 foams is weaker than those of the UC22AMPM counterpart. These differences are associated with the longer hydrophobic chain of UC22AMPM, which imparts a higher viscosity and lower surface tension to foams, resisting the adverse effects of temperature and salinity.

Rapid RAFT Polymerization of Acrylamide with High Conversion.

Rapid RAFT polymerization can significantly improve production efficiency of PAM with designed molecular structure. This study shows that ideal Reversible Addition-Fragmentation Chain Transfer (RAFT) polymerization of acrylamide is achieved in dimethyl sulfoxide (DMSO) solution at 70 °C. The key to success is the appropriate choice of both a suitable RAFT chain transfer agent (CTA) and initiating species. It is illustrated that dodecyl trithiodimethyl propionic acid (DMPA) is a suitable trithiocarbonate RAFT CTA and is synthesized more easily than other CTAs. Compared to other RAFT processes of polymers, the reaction system shortens reaction time, enhances conversion, and bears all the characteristics of a controlled radical polymerization. The calculation result shows that high concentrations can reduce high conversions, accelerate the reaction rate, and widen molecular weight distributions slightly. This work proposes an excellent approach for rapid synthesis of PAMs with a restricted molecular weight distribution.

Hydrophobically Associating Polyacrylamide "Water-in-Water" Emulsion Prepared by Aqueous Dispersion Polymerization: Synthesis, Characterization and Rheological Behavior.

The hydrophobically associating polyacrylamide (HAPAM) is an important kind of water-soluble polymer, which is widely used as a rheology modifier in many fields. However, HAPAM products prepared in a traditional method show disadvantages including poor water solubility and the need for hydrocarbon solvents and appropriate surfactants, which lead to environmental pollution and increased costs. To solve these problems, we reported a novel kind of HAPAM "water-in-water" (w/w) emulsion and its solution properties. In this work, a series of cationic hydrophobic monomers with different alkyl chain lengths were synthesized and characterized. Then, HAPAM w/w emulsions were prepared by the aqueous dispersion polymerization of acrylamide, 2-methylacryloylxyethyl trimethyl ammonium chloride and a hydrophobic monomer. All these emulsions can be stored more than 6 months, showing excellent stability. An optical microscopy observation showed that the particle morphology and the particle size of the HAPAM emulsion were more regular and bigger than the emulsion without the hydrophobic monomer. The solubility tests showed that such HAPAM w/w emulsions have excellent solubility, which took no more than 180 s to dilute and achieve a homogeneous and clear solution. The rheology measurements showed that the HAPAM association increases with a hydrophobe concentration or the length of hydrophobic alkyl chains, resulting in better shear and temperature resistances. The total reduced viscosity was 124.42 mPa·s for cw101, 69.81 mPa·s for cw6-1, 55.38 mPa·s for cw8-0.25, 48.95 mPa·s for cw12-0.25 and 28 mPa·s for cw16-0.25 when the temperature increased from 30 °C to 90 °C. The cw8-2.0 that contains a 2 mol% hydrophobe monomer has the lowest value at 19.12 mPa·s due to the best association. Based on the excellent stability, solubility and rheological properties, we believe that these HAPAM w/w emulsions could find widespread applications.

Selenium-decorated biocompatible honeycomb films with redox-switchable surface for controlling cell adhesion/detachment.

HYPOTHESIS: Selenium (Se)-containing compound is sensitive to redox stimulation, showing hydrophobic-hydrophilic reversible transition. Introduction of such compound into honeycomb film could confer on it redox-switchable surface wettability, which is expected to control cell adhesion/detachment behavior. EXPERIMENTS: Didodecyl selenide was designed and mixed with polystyrene to prepare honeycomb films using "breath figure" method. The film microstructures were characterized by scanning electron microscope and atomic force microscopy, and the arrangement of Se atoms in honeycomb film was determined by X-ray photoelectron spectroscopy and energy dispersive spectrometry. The variation of film wettability upon the alternating stimulation of H2O2 and Vc was examined. Then the cell adhesion, proliferation, and controlled detachment on honeycomb films were conducted. FINDINGS: The introduction of didodecyl selenide helps to form ordered honeycomb film, and Se atoms were found to located on the bottom, pore walls, and top surface of the film. The presence of didodecyl selenide not only greatly improves film biocompatibility by enhancing cell thioredoxin reductase activity, but also imparts the film with H2O2-/vitamin C-regulated tunable wettability that controls cell adhesion and detachment. H2O2 treatment produces a hydrophilic surface for cell adhesion and proliferation, whereas the addition of vitamin C generates hydrophobic surfaces and allows cells to detach while remaining alive with high activity.

An Anti-Turbulence Self-Alignment Method for SINS under Unknown Latitude Conditions.

For the alignment problem of strapdown inertial navigation system (SINS) under the complex environment of unknown latitude, angular oscillation interference, and line interference, the ant colony simulated annealing algorithm of gravity vector optimization is proposed to obtain the gravity apparent motion vector optimization equation, and the polynomial fitting method is proposed to simultaneously perform latitude estimation and self-alignment in combination with the alignment principle of SINS. Simulations and experiments show that the proposed method has more robust anti-interference capability than the traditional interference-based alignment method, the latitude estimation accuracy is improved by six times, the self-alignment yaw angle error RMSE value after obtaining the latitude is within 0.7°, and the roll angle and pitch angle error values are within 0.1°.

Hydrophobically Associating Polymers Dissolved in Seawater for Enhanced Oil Recovery of Bohai Offshore Oilfields.

As compared to China's overall oil reserves, the reserve share of offshore oilfields is rather significant. However, offshore oilfield circumstances for enhanced oil recovery (EOR) include not just severe temperatures and salinity, but also restricted space on offshore platforms. This harsh oil production environment requires polymers with relatively strong salt resistance, solubility, thickening ability, rapid, superior injection capabilities, and anti-shearing ability. As a result, research into polymers with high viscosity and quick solubility is recognized as critical to meeting the criteria of polymer flooding in offshore oil reservoirs. For the above purposes, a novel hydrophobically associating polymer (HAP) was prepared to be used for polymer flooding of Bohai offshore oilfields. The synthetic procedure was free radical polymerization in aqueous solutions starting at 0 °C, using acrylamide (AM), acrylic acid (AA), 2-acrylamido-2-methylpropane sulfonic acid (AMPS), and poly(ethylene glycol) octadecyl methacrylate (POM) as comonomers. It was discovered that under ideal conditions, the molecular weight of HAP exceeds 2.1 × 107 g⋅mol-1. In a simulated reservoir environment, HAP has substantially greater solubility, thickening property, and salt resistance than conventional polyacrylamide (HPAM), with equivalent molecular weight. Finally, the injectivity and propagation of the two polymers in porous media were investigated. Compared with HPAM, which has a similar molecular weight, HAP solution with the concentration of 0.175% had a much better oil displacement effect in the porous medium, which can enhance oil recovery by 8.8%. These discoveries have the potential to pave the way for chemical EOR in offshore oilfields.