In situ derivatization coupled to microextraction by packed sorbentand gas chromatography for the automated determination ofhaloacetic acids in chlorinated water.

A novel analytical method is reported for the determination of monochloroacetic acid, dichloroacetic acid, trichloroacetic acid, monobromoacetic acid, and dibromoacetic acid. These are the five haloacetic acids (HAAs) for which the U.S. Environmental Protection Agency (US EPA) has regulated a maximum contamination level (MCL) of 0.060 mg L−1for the sum of their concentrations in drinking waters. Themethod uses in situ aqueous derivatization, followed by microextraction by packed sorbent (MEPS) priorto gas chromatography­mass spectrometry (GC­MS). The parameters affecting derivatization and extraction were optimized with a view to obtaining maximum sensitivity. The HAAs were derivatized with 2,2,2-trifluroethylamine (TFEA), using N-ethyl-N'-(3-dimethylaminopropyl) carbodiimide (EDC) as a condensation agent. The reaction occurred in aqueous medium and was carried out in 10 min in the vial of anautosampler used to perform microextraction by packed sorbent. The whole process, from the mixing of the reagents for the derivatization, was automated. Precision values varied from 4.2 to 9.8% (as intra-day relative standard deviation, RSD) and 9.4 to 14% (as inter-day RSD). The recoveries from spiked concentrations ranged from 83 to 117%, revealing the accuracy of the method. The detection limits ranged from 0.36 to 1.2 g L−1, such that it is possible to measure the US EPA MCL in drinking waters. The method developed was applied to the analysis of HAAs in drinking and swimming pool water from Salamanca(North West of Spain).

Determination of chlorobenzenes in water samples based on fully automated microextraction by packed sorbent coupled with programmed temperature vaporization-gas chromatography-mass spectrometry.

A fully automated method consisting of microextraction by packed sorbent (MEPS) coupled directly to programmed temperature vaporizer-gas chromatography-mass spectrometry (PTV-GC-MS) has been developed to determine the 12 chlorobenzene congeners (chlorobenzene; 1,2-, 1,3-, and 1,4-dichlorobenzene; 1,2,3-, 1,2,4-, and 1,3,5-trichlorobenzene; 1,2,3,4-, 1,2,3,5-, and 1,2,4,5-tetrachlorobenzene; pentachlorobenzene; and hexachlorobenzene) in water samples. The effects of the variables on MEPS extraction, using a C18 sorbent, and the instrumental PTV conditions were studied. The internal standard 1,4-dichlorobenzene d4 was used as a surrogate. The proposed method afforded good reproducibility, with relative standard deviations (RSD %) lower than 12%. The limits of detection varied between 0.0003 µg L(-1) for 1,2,3,4-tetrachlorobenzene and 0.07 µg L(-1) for 1,3- and 1,4-dichlorobenzene, while those of quantification varied between 0.001 µg L(-1) and 0.2 µg L(-1) for the same compounds. Accuracy of the proposed method was confirmed by applying it to the determination of chlorobenzenes in different spiked water samples, including river, reservoir, and effluent wastewater.

GC-MS determination of parabens, triclosan and methyl triclosan in water by in situ derivatisation and stir-bar sorptive extraction.

Stir-bar sorptive extraction in combination with an in situ derivatisation reaction and thermal desorption-gas chromatography-mass spectrometry was successfully applied to determine parabens (methylparaben, isopropylparaben, n-propylparaben, butylparaben and benzylparaben), triclosan and methyltriclosan in water samples. This approach improves both the extraction efficiency and the sensitivity in the GC in a simple way since the derivatisation reaction occurs at the same time as the extraction procedure. The in situ derivatisation reaction was carried out with acetic anhydride under alkaline conditions. Thermal desorption parameters (cryofocusing temperature, desorption flow, desorption time, desorption temperature) were optimised using a Box-Behnken experimental design. All the analytes gave recoveries higher than 79%, except methylparaben (22%). The method afforded detection limits between 0.64 and 4.12 ng/L, with good reproducibility and accuracy values. The feasibility of the method for the determination of analytes in water samples was checked in tap water and untreated and treated wastewater.

In situ derivatization reaction and determination of ibuprofen in water samples using headspace generation-programmed temperature vaporization-gas chromatography-mass spectrometry.

The aim of the present work is to propose a method for the determination of ibuprofen, as a typical representative of pharmaceutical compounds, in aqueous samples. To do so, an in situ derivatization reaction in aqueous medium was employed in the vial of a headspace sampler (HS), after which instrumental measurements were made with gas chromatography-mass spectrometry (GC-MS). As the injection system we propose a programmed temperature vaporizer (PTV) where, in solvent vent mode, better results can be obtained than with the conventional split and splitless injection modes. Since the derivatization reaction takes place in the HS vial, after the mixing of reagents and the sealing of the vial, the whole process takes place on-line, with no need for intermediate steps. The simplicity and speed of the method--analysis throughput: 10.5 min--together with the limit of detection obtained (0.23 microg/L), bearing in mind that no preconcentration step or later clean-up step are required, make this a good method for the analysis of ibuprofen in aqueous samples of urban waste water.

Determination of filbertone in spiked olive oil samples using headspace-programmed temperature vaporization-gas chromatography-mass spectrometry.

A sensitive method for the fast analysis of filbertone in spiked olive oil samples is presented. The applicability of a headspace (HS) autosampler in combination with a gas chromatograph (GC) equipped with a programmable temperature vaporizer (PTV) and a mass spectrometric (MS) detector is explored. A modular accelerated column heater (MACH) was used to control the temperature of the capillary gas chromatography column. This module can be heated and cooled very rapidly, shortening total analysis cycle times to a considerable extent. The proposed method does not require any previous analyte extraction, filtration and preconcentration step, as in most methods described to date. Sample preparation is reduced to placing the olive oil sample in the vial. This reduces the analysis time and the experimental errors associated with this step of the analytical process. By using headspace generation, the volatiles of the sample are analysed without interference by the non-volatile matrix, and by using injection in solvent-vent mode at the PTV inlet, most of the compounds that are more volatile than filbertone are purged and the matrix effect is minimised. Use of a liner packed with Tenax-TA allowed the compound of interest to be retained during the venting process. The limits of detection and quantification were as low as 0.27 and 0.83 microg/L, respectively, and precision (measured as the relative standard deviation) was 5.7%. The method was applied to the determination of filbertone in spiked olive oil samples and the results revealed the good accuracy obtained with the method.

Use of a programmed temperature vaporizer and an in situ derivatization reaction to improve sensitivity in headspace-gas chromatography. Application to the analysis of chlorophenols in water.

In the present work we propose the combined use of a derivatization reaction within the vial of a headspace sampler with a programmed temperature vaporizer (PTV) inlet in the solvent vent mode as a new methodology for obtaining an increase in sensitivity in headspace-gas chromatography (HS-GC) for the analysis of sparingly volatile compounds. As test analytes the following chlorophenols were used: 2-chlorophenol (2CP), 2,4-dichlorophenol (24DCP), 4-chloro-3-methylphenol (4C3MP) and 2,4,6-trichlorophenol (246TCP). The derivatization reaction was carried out with acetic anhydride because it can be carried out in situ in aqueous medium. In the programmed temperature vaporizer inlet, three different liners, one of them empty and the others with materials of different trapping strengths (glass wool and Tenax-TA), were compared. The best results were obtained when an empty liner was used, with better repeatability and S/N ratios. In the case of the liner filled with Tenax-TA, a considerable lack of repeatability was observed, this being attributed to interactions between the derivatized compounds and the adsorbent. The proposed methodology affords very low limits of detection, in the range of a few ng/L for all the compounds, with good precision and accuracy values.

Determination of aromatic and polycyclic aromatic hydrocarbons in gasoline using programmed temperature vaporization-gas chromatography-mass spectrometry.

A sensitive method is presented for the fast analysis of three aromatic and six polycyclic aromatic hydrocarbons (biphenyl, 3-methylbiphenyl, 4-methylbiphenyl, fluorene, phenanthrene, fluoranthene, pyrene, 1,2-benz(a)anthracene and chrysene) in gasoline samples. The applicability of a GC device equipped with a programmable temperature vaporizer (PTV) and an MS detector is explored. Additionally, a modular accelerated column heater (MACH) was used to control the temperature of the capillary gas chromatography column. This module can be heated and cooled very rapidly, making total analysis cycle times very short. The proposed method does not require any previous analyte extraction and preconcentration step, as in most methods described to date. Sample preparation is reduced to simply diluting the gasoline samples in methanol. This reduces the experimental errors associated with this step of the analytical process. By using sampling injection in the solvent vent mode, and through choice of a suitable temperature, the lightest major components of the gasoline were removed. Moreover, use of a liner packed with Tenax-TA allowed the compounds of interest to be retained during the process. This working strategy could be extended to other groups of compounds through the choice of different venting temperatures. In this way, a large part of the gasoline components are eliminated, the life of the liner is prolonged, and it is possible to inject sample volumes that will not saturate the chromatographic column. The limits of detection ranged from 0.61 microg/L (pyrene) to 6.1 microg/L (biphenyl), and precision (measured as the relative standard deviation) was equal to or lower than 7.3%. The method was applied to the determination of analytes in gasoline samples and the results obtained can be considered highly satisfactory.

Simultaneous determination of gasoline oxygenates and benzene, toluene, ethylbenzene and xylene in water samples using headspace-programmed temperature vaporization-fast gas chromatography-mass spectrometry.

A sensitive method is presented for the fast analysis of seven fuel oxygenates (methanol, ethanol, tert-butyl alcohol (TBA), methyl tert-butyl ether (MTBE), ethyl tert-butyl ether (ETBE), tert-amyl methyl ether (TAME) and diisopropyl ether (DIPE)) and benzene, toluene, ethylbenzene and p-xylene (BTEX) in water samples. The applicability of a headspace (HS) autosampler in combination with a GC device equipped with a programmable temperature vaporizer (PTV) and a MS detector is explored. The proposed method achieves a clear improvement in sensitivity with respect to conventional headspace methods due to the use of the PTV. Two different packed liners with materials of different trapping strengths (glass wool and Tenax-TA) were compared. The benefits of using Tenax-TA instead of glass wool as packed material for the measurement of the 11 compounds emerged as better signal-to-noise ratios and hence better detection limits. The proposed method is extremely sensitive. The limits of detection are of the order of ng/L for six of the compounds studied and of the order of microg/L for the rest, with the exception of the most polar and volatile compound: methanol. Precision (measured as the relative standard deviation for a level with an S/N ratio close to 3) was equal to or lower than 15% in all cases. The method was applied to the determination of the analytes in natural matrixes (tap, river and sea water) and the results obtained can be considered highly satisfactory. The methodology has much lower detection limits than the concentration limits proposed in drinking water by the US Environmental Protection Agency (EPA) and the European Union for compounds under regulation.

Determination of benzene in gasoline using direct injection-mass spectrometry.

A high-speed determination of benzene in gasoline samples using a non-separative method based on direct injection into the mass spectrometer is proposed. The results obtained are very similar to those provided with fast GC-MS. The calibration set was made up of gasoline samples in which the benzene was determined chromatographically and samples of gasoline subjected to a process of evaporation--until the complete disappearance of the original benzene--to which known concentrations of this compound had been added. A PLS1 multivariate calibration model was constructed. Cross-validation was used to select the optimum number of PLS components. The prediction capacity of the model was checked with an additional group of gasoline samples that had not been used either in the construction or in the validation of the model. With the direct injection method proposed here it was possible to analyse 24 samples over a period of 1h. The direct injection method is rapid, simple and--in view of the results--highly suitable for the determination of benzene in gasoline samples.

Determination of methyl tert-butyl ether in gasoline: a comparison of three fast methods based on mass spectrometry.

A high-speed quantitative analysis of methyl tert-butyl ether (MTBE) using three different methods with mass spectrometry detection has been performed. The first method is based on fast chromatography and required an analysis time of 5.23 min per sample, although a certain period (6 min) was necessary for the initial measurement conditions to be regained prior to analysing the next sample. The other two are non-separative methods and are based on direct injection and headspace generation. The analysis times were 1.5 and 3.5 min, respectively, although in the latter case an additional period of time was required to extract volatiles from the sample. The analytical characteristics of all three methods are highly satisfactory in terms of linearity, lack of fit, precision and accuracy. The methods were applied to the determination of MTBE in different gasoline samples. The non-separative methods afforded slightly higher concentrations than those found when fast chromatography was used; this is due to the presence of other minor components that contribute to the abundance of the ion at m/z 73, characteristic of MTBE. We propose a correction that removes this error very satisfactorily and allows the same results to be obtained with all three methodologies proposed.