Enhancing Hydrogen Evolution Reaction via Synergistic Interaction between the [Mo3S13]2- Cluster Co-Catalyst and WSe2 Photocathode.

A thiomolybdate [Mo3S13]2- nanocluster is a promising catalyst for hydrogen evolution reaction (HER) due to the high number of active edge sites. In this work, thiomolybdate cluster films are prepared by spin-coating of a (NH4)2Mo3S13 solution both on FTO glass substrates as hydrogen evolving electrodes and on highly 00.1-textured WSe2 for photoelectrochemical water splitting. As an electrocatalyst, [Mo3S13]2- clusters demonstrate a low overpotential of 220 mV at 10 mA cm-2 in 0.5 M H2SO4 electrolyte (pH 0.3) and remain structurally stable during the electrochemical cycling as revealed by in situ Raman spectroscopy. Moreover, as a co-catalyst on WSe2, [Mo3S13]2- clusters enhance the photocurrent substantially by more than two orders of magnitude (from 0.02 to 2.8 mA cm-2 at 0 V vs RHE). The synergistic interactions between the photoelectrode and catalyst, i.e., surface passivation and band bending modification by the [Mo3S13]2- cluster film, promoted HER catalytic activity of [Mo3S13]2- clusters influenced by the WSe2 support, are revealed by intensity-modulated photocurrent spectroscopy and density functional theory calculations, respectively. The band alignment of the WSe2/[Mo3S13]2- heterojunction, which facilitates the electron injection, is determined by correlating UV-vis with photoelectron yield spectroscopy results.

On the Origin of the OER Activity of Ultrathin Manganese Oxide Films.

There is an urgent need for cheap, stable, and abundant catalyst materials for photoelectrochemical water splitting. Manganese oxide is an interesting candidate as an oxygen evolution reaction (OER) catalyst, but the minimum thickness above which MnOx thin films become OER-active has not yet been established. In this work, ultrathin (<10 nm) manganese oxide films are grown on silicon by atomic layer deposition to study the origin of OER activity under alkaline conditions. We found that MnOx films thinner than 1.5 nm are not OER-active. X-ray photoelectron spectroscopy shows that this is due to electrostatic catalyst-support interactions that prevent the electrochemical oxidation of the manganese ions close to the interface with the support, while in thicker films, MnIII and MnIV oxide layers appear as OER-active catalysts after oxidation and electrochemical treatment. From our investigations, it can be concluded that one MnIII,IV-O monolayer is sufficient to establish oxygen evolution under alkaline conditions. The results of this study provide important new design criteria for ultrathin manganese oxide oxygen evolution catalysts.

Angular momentum-induced delays in solid-state photoemission enhanced by intra-atomic interactions.

Attosecond time-resolved photoemission spectroscopy reveals that photoemission from solids is not yet fully understood. The relative emission delays between four photoemission channels measured for the van der Waals crystal tungsten diselenide (WSe2) can only be explained by accounting for both propagation and intra-atomic delays. The intra-atomic delay depends on the angular momentum of the initial localized state and is determined by intra-atomic interactions. For the studied case of WSe2, the photoemission events are time ordered with rising initial-state angular momentum. Including intra-atomic electron-electron interaction and angular momentum of the initial localized state yields excellent agreement between theory and experiment. This has required a revision of existing models for solid-state photoemission, and thus, attosecond time-resolved photoemission from solids provides important benchmarks for improved future photoemission models.

On an Easy Way To Prepare Metal-Nitrogen Doped Carbon with Exclusive Presence of MeN4-type Sites Active for the ORR.

Today, most metal and nitrogen doped carbon catalysts for ORR reveal a heterogeneous composition. This can be reasoned by a nonoptimized precursor composition and various steps in the preparation process to get the required active material. The significant presence of inorganic metal species interferes with the assignment of descriptors related to the ORR activity and stability. In this work we present a simple and feasible way to reduce the contribution of inorganic metal species in some cases even down to zero. Such catalysts reveal the desired homogeneous composition of MeN4 (Me = metal) sites in the carbon that is accompanied by a significant enhancement in ORR activity. Among the work of other international groups, our iron-based catalyst comprises the highest density of FeN4 sites ever reported without interference of inorganic metal sites.

Microcontact-printing-assisted access of graphitic carbon nitride films with favorable textures toward photoelectrochemical application.

An "ink" (cyanamide) infiltrated anodic aluminum oxide (AAO) stamp is found capable of printing carbon nitride films featuring regular microstructures of the stamp onto the substrates via in situ "chemical vapor deposition". A photocurrent density of 30.2 µA cm(-2 --) at 1.23 VRHE is achieved for a film on a conductive substrate, which is so far the highest value for pure carbon nitride based photoelectrochemical devices.

Photoelectrochemical properties of (In,Ga)N nanowires for water splitting investigated by in situ electrochemical mass spectroscopy.

We investigated the photoelectrochemical properties of both n- and p-type (In,Ga)N nanowires (NWs) for water splitting by in situ electrochemical mass spectroscopy (EMS). All NWs were prepared by plasma-assisted molecular beam epitaxy. Under illumination, the n-(In,Ga)N NWs exhibited an anodic photocurrent, however, no O2 but only N2 evolution was detected by EMS, indicating that the photocurrent was related to photocorrosion rather than water oxidation. In contrast, the p-(In,Ga)N NWs showed a cathodic photocurrent under illumination which was correlated with the evolution of H2. After photodeposition of Pt on such NWs, the photocurrent density was significantly enhanced to 5 mA/cm(2) at a potential of -0.5 V/NHE under visible light irradiation of ∼40 mW/cm(2). Also, incident photon-to-current conversion efficiencies of around 40% were obtained at -0.45 V/NHE across the entire visible spectral region. The stability of the NW photocathodes for at least 60 min was verified by EMS. These results suggest that p-(In,Ga)N NWs are a promising basis for solar hydrogen production.

Ruthenium sulphide thin layers as catalysts for the electrooxidation of water.

Crystalline RuS(2) layers were prepared on titanium sheets by reactive magnetron sputtering using a metallic ruthenium target and a H(2)S-Ar mixture as process gas. The ability of these layers for the electrooxidation of water (OER) was investigated by differential electrochemical mass spectrometry (DEMS) in 0.5 M H(2)SO(4) electrolyte. It was observed that the activity for water oxidation is increased with increasing temperature of the titanium substrate during the sputter deposition process whereas a competitive corrosion process is diminished. The reason for this effect seems to be a better crystallinity of these layers at higher substrate temperatures as it is proved by XRD analysis. In contrast to RuS(2) single crystals no photo effect could be observed on the sputtered layers under illumination with a tungsten lamp. Time resolved microwave conductivity analysis indicates the presence of mobile charge carriers after illumination but apparently these cannot participate in the electrooxidation of water.

Surface aspects of sol-gel derived hematite films for the photoelectrochemical oxidation of water.

α-Fe(2)O(3) (hematite) photoanodes for the oxygen evolution reaction (OER) were prepared by a cost-efficient sol-gel procedure. Due to low active photoelectrochemical properties observed, it is assumed that the sol-gel procedure leads to hematite films with defects and surface states on which generated charge carriers are recombined or immobilized in trap processes. Electrochemical activation was proven to diminish unfavourable surface groups to some extent. More efficiently, a plasma treatment improves significantly the photoelectrochemical properties of the OER. X-ray photoelectron spectroscopy (XPS) analysis reveals an oxygen enriched surface layer with new oxygen species which may be responsible for the improved electrochemical activity. Due to surface photovoltage an increased fraction of transferred charge carriers from these newly produced surface defects are identified.

Automated quantitative 3D analysis of faceting of particles in tomographic datasets.

Characterization of facets of particles is a common problem. In this paper an algorithm is presented which allows automated quantitative 3D analysis of facets of many particles within tomographic datasets. The algorithm is based on the analysis of probability distributions of the orientations of triangle normals of mesh representations. The result consists of lists containing number of detected facets, their size, global orientation and the interplanar angles between facets for each analyzed particle. Characterization of each particle according to any of these facet properties is then possible, e.g. statistics about different crystal shapes or removal of particles that do not show significant faceting. Analyses of a 3D dataset obtained by focused ion beam (FIB) tomography of a sample containing spinel particles are presented.

Structure of the catalytic sites in Fe/N/C-catalysts for O2-reduction in PEM fuel cells.

Fe-based catalytic sites for the reduction of oxygen in acidic medium have been identified by (57)Fe Mössbauer spectroscopy of Fe/N/C catalysts containing 0.03 to 1.55 wt% Fe, which were prepared by impregnation of iron acetate on carbon black followed by heat-treatment in NH(3) at 950 °C. Four different Fe-species were detected at all iron concentrations: three doublets assigned to molecular FeN(4)-like sites with their ferrous ions in a low (D1), intermediate (D2) or high (D3) spin state, and two other doublets assigned to a single Fe-species (D4 and D5) consisting of surface oxidized nitride nanoparticles (Fe(x)N, with x≤ 2.1). A fifth Fe-species appears only in those catalysts with Fe-contents ≥0.27 wt%. It is characterized by a very broad singlet, which has been assigned to incomplete FeN(4)-like sites that quickly dissolve in contact with an acid. Among the five Fe-species identified in these catalysts, only D1 and D3 display catalytic activity for the oxygen reduction reaction (ORR) in the acid medium, with D3 featuring a composite structure with a protonated neighbour basic nitrogen and being by far the most active species, with an estimated turn over frequency for the ORR of 11.4 e(-) per site per s at 0.8 V vs. RHE. Moreover, all D1 sites and between 1/2 and 2/3 of the D3 sites are acid-resistant. A scheme for the mechanism of site formation upon heat-treatment is also proposed. This identification of the ORR-active sites in these catalysts is of crucial importance to design strategies to improve the catalytic activity and stability of these materials.

Quantitative structural assessment of heterogeneous catalysts by electron tomography.

We present transmission electron microscope (TEM) tomography investigations of ruthenium-based fuel cell catalyst materials as employed in direct methanol fuel cells (DMFC). The digital three-dimensional representation of the samples not only enables detailed studies on number, size, and shape but also on the local orientation of the ruthenium particles to their support and their freely accessible surface area. The shape analysis shows the ruthenium particles deviate significantly from spherical symmetry which increases their surface to volume ratio. The morphological studies help to understand the structure formation mechanisms during the fabrication as well as the high effectiveness of these catalysts in the oxygen reduction reaction at the cathode side of fuel cells.

Unveiling N-protonation and anion-binding effects on Fe/N/C-catalysts for O2 reduction in PEM fuel cells.

The high cost of proton-exchange-membrane fuel cells would be considerably reduced if platinumbased catalysts were replaced by iron-based substitutes, which have recently demonstrated comparable activity for oxygen reduction, but whose cause of activity decay in acidic medium has been elusive. Here, we reveal that the activity of Fe/N/C-catalysts prepared through a pyrolysis in NH3 is mostly imparted by acid-resistant FeN4-sites whose turnover frequency for the O2 reduction can be regulated by fine chemical changes of the catalyst surface. We show that surface N-groups protonate at pH 1 and subsequently bind anions. This results in decreased activity for the O2 reduction. The anions can be removed chemically or thermally, which restores the activity of acid-resistant FeN4-sites. These results are interpreted as an increased turnover frequency of FeN4-sites when specific surface N-groups protonate. These unprecedented findings provide new perspective for stabilizing the most active Fe/N/C-catalysts known to date.