Efficient in Situ One-Pot Synthesis of Water-Soluble Hydroxynaphthoquinones for Redox Flow Batteries.

Given the importance of energy storage and its hybridization with renewable technologies for the energy transition, the development of redox flow batteries (RFB) is receiving particular attention. Among the various emerging technologies, aqueous organic redox flow batteries (AORFBs) are of particular interest, as the objectives in terms of durability, cost, and safety can be achieved thanks to the possibilities offered by molecular engineering. While anthraquinones have been widely explored as negolytes, few works report the use of naphthoquinones. This work aims to exploit an innovative in situ and cost-effective method for the one-pot synthesis of water-soluble naphthoquinones for application as a negolyte in redox flow batteries. As exemplified with alizarin, the energy of the naphthoquinone synthetic reaction in fuel cell mode can be recovered and the electrolyte solution used directly in redox flow batteries without purification. A 0.3 M naphthoquinone solution paired with 0.6 M ferrocyanide demonstrated good stability compared with other naphthoquinones, with a capacity fade rate of 0.017%/cycle (0.84%/day) over 320 cycles. Additionally, the system exhibited one of the highest energy efficiencies (82%) and a power density of 80-105 mW cm-2 at 50% SOC. These first results are promising for further exploration of new water-soluble naphthoquinones efficiently synthesized from hydroxyanthraquinones for application in AORFBs.

Electrochemical Properties of Carbon Fibers from Felts.

Electrochemical behaviors of individual carbon fibers coming from carbon felts were investigated using two different redox couples, 1,1'-dimethanolferrocene and potassium ferrocyanide. Electrochemical responses were examined after different oxidation treatments, then simulated and interpreted using the Kissa 1D software and existing models. Our experiments indicate that a crude carbon fiber behaves as an assembly of sites with different electrochemical reactivities. In such case, the Butler-Volmer law is not appropriate to describe the electron transfer kinetics because of the large created overpotential. Oxidation of the fiber erases the effect by increasing the kinetics of the electron transfer probably by a homogenization and increase of the reactivity on all the fiber. Additionally, analysis of the signal shows the large influence of the convection that affects the electrochemical response even at moderate scan rates (typically below 0.1-0.2 V s-1).

Efficient Dechlorination of α-Halocarbonyl and α-Haloallyl Pollutants by Electroreduction on Bismuth.

The electrocatalytic activity of bismuth considered as a low-cost and green electrode material was studied in reductive dechlorination processes. Cyclic voltammetry analyses showed that the Bi electrode exhibited a high catalytic activity to reduce alachlor, a chlorinated herbicide, in the aqueous medium at different pH values. Bulk electrolyses were performed at different potentials and pH values. Alachlor was reduced in deschloroalachlor, its dechlorinated derivative, with a high selectivity (96%) and a current efficiency of 48%. The reductive dechlorination of other chlorinated compounds with an activated carbon atom was then studied, showing that the bismuth electrode catalyzed the electroreduction of chloroacetamides, α-halocarbonyl, and α-haloallyl pollutants. Cyclic voltammetry experiments allowed us to propose a mechanism explaining the high catalytic activity of bismuth to reduce these families of compounds.

Direct and indirect electrochemical reduction prior to a biological treatment for dimetridazole removal.

Two different electrochemical reduction processes for the removal of dimetridazole, a nitroimidazole-based antibiotic, were examined in this work. A direct electrochemical reduction was first carried out in a home-made flow cell in acidic medium at potentials chosen to minimize the formation of amino derivatives and then the formation of azo dimer. Analysis of the electrolyzed solution showed a total degradation of dimetridazole and the BOD5/COD ratio increased from 0.13 to 0.24. An indirect electrochemical reduction in the presence of titanocene dichloride ((C5H5)2TiCl2), which is used to reduce selectively nitro compounds, was then investigated to favour the formation of amino compounds over hydroxylamines and then to prevent the formation of azo and azoxy dimers. UPLC-MS/MS analyses showed a higher selectivity towards the formation of the amino compound for indirect electrolyses performed at pH 2. To confirm the effectiveness of the electrochemical reduction, a biological treatment involving activated sludge was then carried out after direct and indirect electrolyses at different pH. The enhancement of the biodegradability was clearly shown since mineralization yields of all electrolyzed solutions increased significantly.

Sulfamethazine removal by means of a combined process coupling an oxidation pretreatment and activated sludge culture - preliminary results.

A coupled electrochemical process and biological treatment was used to remove a biorecalcitrant antibiotic: sulfamethazine (SMT). The pretreatment was performed in a home-made flow cell involving graphite felt as a working electrode at potentials of 1 and 1.6 V/saturated calomel electrode (SCE); it was followed by a biological process involving activated sludge purchased from a local wastewater treatment plant. Activated sludge cultures of pretreated and non-pretreated SMT solution were carried out for 3 weeks, and different parameters were monitored, especially total organic carbon (TOC) and SMT concentrations. high-performance liquid chromatography results revealed that the target molecule was not assimilated by activated sludge. However, and confirming the improvement previously observed for the biological oxygen demand/chemical oxygen demand (BOD5/COD) ratio, from 0.08 before electrolysis to 0.58 after electrolysis, a pretreatment step in oxidation at 1.6 V/SCE led to a fast decrease of TOC during the subsequent biological treatment, since the mineralization yields increased from 10% for a non-pretreated SMT solution to 76.6% after electrolysis in oxidation (1.6 V/SCE), confirming the efficiency of coupling the electro-oxidation process with a biological treatment for the mineralization of SMT. Moreover, when the electrolysis was performed at 1 V/SCE, no biodegradation was observed, underlining the importance of the electrochemical pretreatment.

Degradation of enoxacin antibiotic by the electro-Fenton process: Optimization, biodegradability improvement and degradation mechanism.

This study aims to investigate the effectiveness of the electro-Fenton process on the removal of a second generation of fluoroquinolone, enoxacin. The electrochemical reactor involved a carbon-felt cathode and a platinum anode. The influence of some experimental parameters, namely the initial enoxacin concentration, the applied current intensity and the Fe(II) amount, was examined. The degradation of the target molecule was accompanied by an increase of the biodegradability, assessed from the BOD5 on COD ratio, which increased from 0 before treatment until 0.5 after 180 min of electrolysis at 50 mg L(-1) initial enoxacin concentration, 0.2 mmol L(-1) Fe(II) concentration and 300 mA applied current intensity. TOC and COD time-courses were also evaluated during electrolysis and reached maximum residual yields of 54% and 43% after 120 min of treatment, respectively. Moreover, a simultaneous generation of inorganic ions (fluorides, ammonium and nitrates) were observed and 3 short chain carboxylic acids (formic, acetic and oxalic acids) were identified and monitored during 180 min of electrolysis. By-products were identified according to UPLC-MS/MS results and a degradation pathway was proposed.

Relevance of an electrochemical process prior to a biological treatment for the removal of an organophosphorous pesticide, phosmet.

The aim of this study was to examine the feasibility of coupling an electrochemical pre-treatment with a biological step in order to degrade phosmet, an organophosphorous pesticide. Preliminary biodegradation experiments showed that the target molecule was not assimilated by activated sludge. The pre-treatment consisted of potentiostatic electrolysis (-1.3 V/SCE) in a flow cell. After only one pass (1 mL min(-1)), cyclic voltammetry with a vitreous carbon electrode showed a total phosmet reduction in neutral medium confirmed by thin layer chromatography, which also highlighted the presence of several by-products. H NMR spectra of the main by-product showed the absence of the aromatic ring, only the phosphorus part of phosmet has been identified and phosmet-oxon, a very toxic derivative, was not formed. Lower toxicity and higher biodegradability characterized the electrolyzed solution, EC(50) value increased from 7% to 58% and BOD(5) value increased from 4 to 9 mg O(2) L(-1) after electrolysis leading to an increase of the BOD(5) on COD ratio from 0.19 to 0.42 (limit of biodegradability, 0.4). These encouraging results were confirmed during activated sludge culture since an almost total mineralization of the electrolyzed solution was recorded (97%), confirming the feasibility of the proposed coupled process.