Characterization of Inorganic Scintillator Detectors for Dosimetry in Image-Guided Small Animal Radiotherapy Platforms.

The purpose of the study was to characterize a detection system based on inorganic scintillators and determine its suitability for dosimetry in preclinical radiation research. Dose rate, linearity, and repeatability of the response (among others) were assessed for medium-energy X-ray beam qualities. The response's variation with temperature and beam angle incidence was also evaluated. Absorbed dose quality-dependent calibration coefficients, based on a cross-calibration against air kerma secondary standard ionization chambers, were determined. Relative output factors (ROF) for small, collimated fields (≤10 mm × 10 mm) were measured and compared with Gafchromic film and to a CMOS imaging sensor. Independently of the beam quality, the scintillator signal repeatability was adequate and linear with dose. Compared with EBT3 films and CMOS, ROF was within 5% (except for smaller circular fields). We demonstrated that when the detector is cross-calibrated in the user's beam, it is a useful tool for dosimetry in medium-energy X-rays with small fields delivered by Image-Guided Small Animal Radiotherapy Platforms. It supports the development of procedures for independent "live" dose verification of complex preclinical radiotherapy plans with the possibility to insert the detectors in phantoms.

A prototype low-cost secondary standard calorimeter for reference dosimetry with ultra-high pulse dose rates.

OBJECTIVES: Ultra-high pulse dose rate modalities present significant dosimetry challenges for ionisation chambers due to significant ion recombination. Conversely, calorimeters are ideally suited to measure high dose, short duration dose deliveries and this work describes a simple calorimeter as an alternative dosemeter for use in the clinic. METHODS: Calorimeters were constructed featuring a disc-shaped core and single sensing thermistor encased in a 3D-printed body shaped like a Roos ionisation chamber. The thermistor forms one arm of a DC Wheatstone bridge, connected to a standard DMM. The bridge-out-of-balance voltage was calibrated in terms of temperature. A graphite-core calorimeter was calibrated in terms of absorbed dose to water (J/kg) in Co-60 and conventional 6, 10 and 15 MV X-rays. Similarly, an aluminium-core calorimeter was calibrated in a conventional 20 MeV electron beam and tested in a research high dose per pulse 6 MeV electron beam. RESULTS: Calorimeters were successfully calibrated in terms of absorbed dose to water in conventional radiotherapy beams at approximately 5 Gy/min with an estimated uncertainty of ±2-2.5% (k = 2), and performed similarly in a 6 MeV electron beam delivering approximately 180 Gy/s. CONCLUSIONS: A simple, low-cost calorimeter traceably calibrated to existing primary standards of absorbed dose could be used as a secondary standard for dosimetry for ultra-high pulse dose rates in the clinic. ADVANCES IN KNOWLEDGE: Secondary standard calorimeters for routine measurements are not available commercially; this work presents the basis of a simple, low-cost solution for reference dosimetry for ultra-high pulse dose rate beams.

DECAL: A Reconfigurable Monolithic Active Pixel Sensor for Tracking and Calorimetry in a 180 nm Image Sensor Process.

In this paper, we describe DECAL, a prototype Monolithic Active Pixel Sensor (MAPS) device designed to demonstrate the feasibility of both digital calorimetry and reconfigurability in ASICs for particle physics. The goal of this architecture is to help reduce the development and manufacturing costs of detectors for future colliders by developing a chip that can operate both as a digital silicon calorimeter and a tracking chip. The prototype sensor consists of a matrix of 64 × 64 55 µm pixels, and provides a readout at 40 MHz of the number of particles which have struck the matrix in the preceding 25 ns. It can be configured to report this as a total sum across the sensor (equivalent to the pad of an analogue calorimeter) or the sum per column (equivalent to a traditional strip detector). The design and operation of the sensor are described, and the results of chip characterisation are reported and compared to simulations.

Evaluation of a pixelated large format CMOS sensor for x-ray microbeam radiotherapy.

PURPOSE: Current techniques and procedures for dosimetry in microbeams typically rely on radiochromic film or small volume ionization chambers for validation and quality assurance in 2D and 1D, respectively. Whilst well characterized for clinical and preclinical radiotherapy, these methods are noninstantaneous and do not provide real time profile information. The objective of this work is to determine the suitability of the newly developed vM1212 detector, a pixelated CMOS (complementary metal-oxide-semiconductor) imaging sensor, for in situ and in vivo verification of x-ray microbeams. METHODS: Experiments were carried out on the vM1212 detector using a 220 kVp small animal radiation research platform (SARRP) at the Helmholtz Centre Munich. A 3 x 3 cm2 square piece of EBT3 film was placed on top of a marked nonfibrous card overlaying the sensitive silicon of the sensor. One centimeter of water equivalent bolus material was placed on top of the film for build-up. The response of the detector was compared to an Epson Expression 10000XL flatbed scanner using FilmQA Pro with triple channel dosimetry. This was also compared to a separate exposure using 450 µm of silicon as a surrogate for the detector and a Zeiss Axio Imager 2 microscope using an optical microscopy method of dosimetry. Microbeam collimator slits with range of nominal widths of 25, 50, 75, and 100 µm were used to compare beam profiles and determine sensitivity of the detector and both film measurements to different microbeams. RESULTS: The detector was able to measure peak and valley profiles in real-time, a significant reduction from the 24 hr self-development required by the EBT3 film. Observed full width at half maximum (FWHM) values were larger than the nominal slit widths, ranging from 130 to 190 µm due to divergence. Agreement between the methods was found for peak-to-valley dose ratio (PVDR), peak to peak separation and FWHM, but a difference in relative intensity of the microbeams was observed between the detectors. CONCLUSIONS: The investigation demonstrated that pixelated CMOS sensors could be applied to microbeam radiotherapy for real-time dosimetry in the future, however the relatively large pixel pitch of the vM1212 detector limit the immediate application of the results.