ABSTRACT
Tracer flux ratio (TFR) methodology performed downwind of 15 active oil and natural gas production sites in Ohio County, West Virginia sought to quantify air pollutant emissions over two weeks in April 2018. In coordination with a production company, sites were randomly selected depending on wind forecasts and nearby road access. Methane (CH4), ethane (C2H6), and tracer gas compounds (acetylene and nitrous oxide) were measured via tunable infrared direct absorption spectroscopy. Ion signals attributed to benzene (C6H6) and other volatile gases (e.g., C7 - C9 aromatics) were measured via proton-transfer reaction time-of-flight mass spectrometry. Short-term whole facility emission rates for 12 sites are reported. Results from TFR were systematically higher than the sum of concurrent on-site full flow sampler measurements, though not all sources were assessed on-site in most cases. In downwind plumes, the mode of the C2H6:CH4 molar ratio distribution for all sites was 0.2, which agreed with spot sample analysis from the site operator. Distribution of C6H6:CH4 ratios was skew but values between 1 and 5 pptv ppbv-1 were common. Additionally, the aromatic profile has been attributed to condensate storage tank emissions. Average ratios of C7 - C9 to C6H6 were similar to other literature values reported for natural gas wells.
ABSTRACT
In April of 2018, an optical gas imaging (OGI) and full flow sampler (FFS) emissions measurement study of pneumatic controllers (PCs) was conducted at 15 oil and natural gas production sites in West Virginia. The objective of the study was to identify and characterize PC systems with excessive emissions caused by maintenance issues or nonoptimized process conditions. A total of 391 PC systems were found on the sites and all were classified by the operator as snap-acting (on/off) intermittent venting PCs (IPCs) that should exhibit little gas release while the PC is closed between actuation events. The population was comprised of two groups, 259 infrequently actuating, lower emitting (LE) IPCs and 132 gas processing unit (GPU) liquid level IPCs and associated dump valve actuators that vent more frequently and have larger emission volumes. Using a PC-specific OGI inspection protocol with an assumed whole gas OGI detection threshold of 2.0 scfh, only 2 out of 259 LE-IPCs exhibited OGI detectable emissions indicating good inspection and maintenance practices for this category. Due to combined (ganged) GPU exhaust vents, the OGI inspection of the GPU liquid level IPCs was comparatively less informative and determination of single component IPC emissions by the FFS was more difficult. The time resolved FFS measurements of GPU IPCs defined three categories of operation: one that indicated proper function and two associated with higher emissions that may result from an IPC maintenance or process issues. The overall GPU IPC emission distribution was heavy tailed, with a median value of 12.8 scfh, similar to the 13.5 scfh whole gas IPC emission factor (EF). Total emissions were dominated by non-optimal temporal profile high-emitter IPC cases with the top 20% of IPC systems accounting for between 51.3% and 70.7% of GPU liquid level IPC emissions by volume. The uncertainty in the estimate was due to the ganged nature of the GPU exhaust vents. The highest GPU IPC emission came from a single malfunctioning unit with a measured whole gas value of 157 scfh. Up to six IPCs exceeded 100 scfh. An analysis of FFS emission measurements compared to liquids production per IPC unit employed indicated that production sites operating at a high level of liquids production test the limits of the site engineering, likely resulting in higher IPC emissions. Overall, this study found that the LE-IPCs with OGI-verified low closed bleed rates may emit well below the IPC EF while GPU liquid level IPC systems are likely well represented by the current IPC EF. IPCs that are experiencing a maintenance or process issue or that are operating at sites with a very high product throughput per IPC employed can emit at rates exceeding ten times IPC EF.
ABSTRACT
A measurement campaign characterized methane and other emissions from 15 natural gas production sites. Sites were surveyed using optical gas imaging (OGI) cameras to identify fugitive and vented emissions, with the methane mass emission rate quantified using a full flow sampler. We present storage tank emissions in context of all site emissions, followed by a detailed account of the former. In total, 224 well pad emission sources at 15 sites were quantified yielding a total emission rate of 57.5 ± 2.89 kg/hr for all sites. Site specific emissions ranged from 0.4 to 10.5 kg/hr with arithmetic and geometric means of 3.8 and 2.2 kg/hr, respectively. The two largest categories of emissions by mass were pneumatic devices (35 kg/hr or ~61% of total) and tanks (14.3 kg/hr or ~25% of total). Produced water and condensate tanks at all sites employed emissions control devices. Nevertheless, tanks may still lose gas via component leaks as observed in this study. The total number of tanks at all sites was 153. One site experienced a major malfunction and direct tank measurements were not conducted due to safety concerns and may have represented a super-emitter as found in other studies. The remaining sites had 143 tanks, which accounted for 42 emissions sources. Leaks on controlled tanks were associated with ERVs, PRVs, and thief hatches. Since measurements represented snapshots-in-time and could only be compared with modeled tank emission data, it was difficult to assess real capture efficiencies accurately. Our estimates suggest that capture efficiency ranged from 63 to 92% for controlled tanks.
