ABSTRACT
Manganese oxides are considered to be very promising materials for water oxidation catalysis (WOC), but the structural parameters influencing their catalytic activity have so far not been clearly identified. For this study, a dozen manganese oxides (MnOx ) with various solid-state structures were synthesised and carefully characterised by various physical and chemical methods. WOC by the different MnOx was then investigated with Ce(4+) as chemical oxidant. Oxides with layered structures (birnessites) and those containing large tunnels (todorokites) clearly gave the best results with reaction rates exceeding 1250 ${{\rm{mmol}}_{{\rm{O}}_{\rm{2}} } }$ ${{\rm{mol}}_{{\rm{Mn}}}^{ - 1} }$ h(-1) or about 50 µmolO2 m(-2) h(-1) . In comparison, catalytic rates per mole of Mn of oxides characterised by well-defined 3D networks were rather low (e.g., ca. 90 ${{\rm{mmol}}_{{\rm{O}}_{\rm{2}} } }$ ${{\rm{mol}}_{{\rm{Mn}}}^{ - 1} }$ h(-1) for bixbyite, Mn2 O3 ), but impressive if normalised per unit surface area (>100 ${{\rm{{\rm \mu} mol}}_{{\rm{O}}_{\rm{2}} } }$ m(-2) h(-1) for marokite, CaMn2 O4 ). Thus, two groups of MnOx emerge from this screening as hot candidates for manganese-based WOC materials: 1) amorphous oxides with tunnelled structures and the well-established layered oxides; 2) crystalline Mn(III) oxides. However, synthetic methods to increase surface areas must be developed for the latter to obtain good catalysis rates per mole of Mn or per unit catalyst mass.
ABSTRACT
In this work, magnetic nanocomposite particles were prepared for water oxidation reactions. The studied catalysts consist of maghemite (γ-Fe2O3), magnetite (Fe3O4), and manganese ferrite (MnFe2O4) nanoparticles as cores coated in situ with birnessite-type manganese oxide shells and were characterized by X-ray diffraction, transmission electron microscopy, scanning electron microscopy, thermal, chemical, and surface analyses, and magnetic measurements. The particles were found to be of nearly spherical core-shell architectures with average diameter of 150 nm. Water oxidation catalysis was examined using Ce(4+) as the sacrificial oxidant. All core-shell particles were found to be active water oxidation catalysts. However, the activity was found to depend on a variety of factors like the type of iron oxide core, the structure and composition of the shell, the coating characteristics, and the surface properties. Catalysts containing magnetite and manganese ferrite as core materials displayed higher catalytic activities per manganese ion (2650 or 3150 mmolO2 molMn(-1) h(-1)) or per mass than nanoiron oxides (no activity) or birnessite alone (1850 mmolO2 molMn(-1) h(-1)). This indicates synergistic effects between the MnOx shell and the FeOx core of the composites and proves the potential of the presented core-shell approach for further catalyst optimization. Additionally, the FeOx cores of the particles allow magnetic recovery of the catalyst and might also be beneficial for applications in water-oxidizing anodes because the incorporation of iron might enhance the overall conductivity of the material.
ABSTRACT
Layered manganese oxides from the birnessite mineral family have been identified as promising heterogeneous compounds for water-oxidation catalysis (WOC), a key reaction for the conversion of renewable energy into storable fuels. High catalytic rates were especially observed for birnessites which contain calcium as part of their structures. With the aim to systematically improve the catalytic performance of such oxide materials, we used a flexible synthetic route to prepare three series of calcium birnessites, where we varied the calcium concentrations, the ripening times of the original precipitates and the temperature of the heat treatment following the initial synthetic steps (tempering) during the preparation process. The products were carefully analysed by a number of analytical techniques and then probed for WOC activity using the Ce(4+)-system. We find that our set of twenty closely related manganese oxides shows large, but somewhat systematic alterations in catalytic rates, indicating the importance of synthesis parameters for maximum catalytic performance. The catalyst of the series for which the highest water-oxidation rate was found is a birnessite of medium calcium content (Ca : Mn ratio 0.2 : 1) that had been subjected to a tempering temperature of 400 °C. On the basis of the detailed analysis of the results, a WOC reaction scheme for birnessites is proposed to explain the observed trends in reactivity.
