Evaluating trunnionosis in modular anatomic shoulder arthroplasties: a retrieval study.

BACKGROUND: Shoulder arthroplasty procedures are widely indicated, and the number of shoulder arthroplasty procedures has drastically increased over the years. Rapid expansion of the utilization of reverse total shoulder arthroplasty has outpaced the more modest growth of anatomic total shoulder arthroplasty (aTSA) while shoulder hemiarthroplasty (HA) has trended down. Recently, shoulder prostheses have transitioned to increasingly modular systems offering more individualized options with the potential for decreased pain and increased range of motion. However, increased primary procedures has resulted in increased revision surgeries, with one potential cause being fretting and corrosion damage within these modular systems. METHODS: Following institutional review board approval, 130 retrieved aTSA and 135 HA explants were identified through database query. Humeral stem and head components were included in all 265 explants, whereas 108 included polyethylene glenoid liner components. All explanted components were macroscopically evaluated for standard damage modes, and taper junctions were microscopically examined for fretting/corrosion using a modified Goldberg-Cusick classification system that was 4-quadrant graded for both the male and female component. Medical records were reviewed for patient demographics and surgical information. RESULTS: In this series, 158 of explants were from female patients (male = 107), and 162 explants were from the right shoulder. Average age at implantation was 61 years (range: 24-83), average age at explanation was 66 years (range, 32-90), and average duration of implantation was 61.4 months (range, 0.5-240). Scratching, edge deformation, and burnishing were the most commonly observed standard damage modes. Of the 265 explants, 146 had a male stem component vs. 118 with a female stem component. Average summed fretting grades on male and female stem components were 8.3 and 5.9, respectively (P < .001). Average summed corrosion grades for male and female stem components were 8.2 and 6.2, respectively (P < .001). Wider male tapers (>11 mm) showed significantly less fretting and corrosion (P < .001). Lastly, mismatched metal compositions between the head and stem components showed greater fretting and corrosion damage (P = .002). CONCLUSION: In this series of 265 aTSA and HA explants, there was substantial damage present on the explanted components. All components demonstrated macroscopic damage. In this retrieval study, small-tapered male stems with small, thin female heads and mismatched metal composition between components were risk factors for increased implant wear. As shoulder arthroplasty volume increases, optimizing design is paramount for long-term success. Additional work could determine the clinical significance of these findings.

Larger-diameter trunnions and bolt-reinforced taper junctions are associated with less tribocorrosion in reverse total shoulder arthroplasty.

BACKGROUND: Morse taper junction tribocorrosion is recognized as an important failure mode in total hip arthroplasty. Although taper junctions are used in almost all shoulder arthroplasty systems currently available in the United States, with large variation in design, limited literature has described comparable analyses of taper damage in these implants. In this study, taper junction damage in retrieved reverse total shoulder arthroplasty (RTSA) implants was assessed and analyzed. METHODS: Fifty-seven retrieved RTSAs with paired baseplate and glenosphere components with Morse taper junctions were identified via database query; 19 of these also included paired humeral stems and trays or spacers with taper junctions. Components were graded for standard damage modes and for fretting and corrosion with a modified Goldberg-Cusick classification system. Medical records and preoperative radiographs were reviewed. Comparative analyses were performed assessing the impact of various implant, radiographic, and patient factors on taper damage. RESULTS: Standard damage modes were commonly found at the evaluated trunnion junctions, with scratching and edge deformation damage on 76% and 46% of all components, respectively. Fretting and corrosion damage was also common, observed on 86% and 72% of baseplates, respectively, and 23% and 40% of glenospheres, respectively. Baseplates showed greater moderate to severe (grade ≥ 3) fretting (43%) and corrosion (27%) damage than matched glenospheres (fretting, 9%; corrosion, 13%). Humeral stems showed moderate to severe fretting and corrosion on 28% and 30% of implants, respectively; matched humeral trays or spacers showed both less fretting (14%) and less corrosion (17%). On subgroup analysis, large-tapered implants had significantly lower summed fretting and corrosion grades than small-tapered implants (P < .001 for both) on glenospheres; paired baseplate corrosion grades were also significantly lower (P = .031) on large-tapered implants. Factorial analysis showed that bolt reinforcement of the taper junction was also associated with less fretting and corrosion damage on both baseplates and glenospheres. Summed fretting and corrosion grades on glenospheres with trunnions (male) were significantly greater than on glenospheres with bores (female) (P < .001 for both). CONCLUSIONS: Damage to the taper junction is commonly found in retrieved RTSAs and can occur after only months of being implanted. In this study, tribocorrosion predominantly occurred on the taper surface of the baseplate (vs. glenosphere) and on the humeral stem (vs. tray or spacer), which may relate to the flexural rigidity difference between the titanium and cobalt-chrome components. Bolt reinforcement and the use of large-diameter trunnions led to less tribocorrosion of the taper junction. The findings of this study provide evidence for the improved design of RTSA prostheses to decrease tribocorrosion.

A Survey of Musculoskeletal Disorders in the Orthopaedic Surgeon: Identifying Injuries, Exacerbating Workplace Factors, and Treatment Patterns in the Orthopaedic Community.

INTRODUCTION: As demand for orthopaedic care increases, the orthopaedic community must preserve access to skilled physicians. Workplace hazards and related injuries or conditions contribute to musculoskeletal (MSK) stress on orthopaedic surgeons, which can lead to undesirable medical leaves of absence or early retirement. The purpose of this study was to identify and characterize work-related and non-work-related MSK conditions that affect orthopaedic surgeons and differential injury patterns among male and female surgeons. This study hypothesized that MSK conditions would be exacerbated by work, correlate with age, and show gender-based disparities. Identifying MSK conditions and associated workplace hazards may ultimately help guide preventive or protective efforts. METHODS: Following IRB and society approvals, a modified 15-question physical discomfort survey was emailed to a randomized selection of American Academy of Orthopaedic Surgeons (AAOS) members and all Ruth Jackson Orthopaedic Society members. Data were deidentified and merged by AAOS; analyses were performed by the authors. RESULTS: Most surgeons reported at least one MSK condition (86%; 95% male versus 82% female, P = 0.317), with an average of two conditions per surgeon. Low back pain (56%) and neck pain (42%) were the two most common conditions reported. Male surgeons were more likely to report medial epicondylitis (P = 0.040), lateral epicondylitis (P ≤ 0.001), low back pain (P = 0.001), and lumbar radiculopathy (P = 0.001); however, male respondents were significantly older than female respondents (57 versus 43 years, P ≤ 0.0001), and some conditions were age-correlated. Most respondents reported at least one work-attributed MSK condition (64%; 68% male versus 62% female, P = 0.806). Caseload was not associated with an increased number of work-related MSK conditions; yet, 60% of surgeons reported that work worsened symptoms. Surgical treatment was sought most often for lumbar radiculopathy (6%) and carpal tunnel syndrome (6%). Sixty-nine leaves of absence were reported; most less than 1 month (55%). Exacerbating workplace factors included positioning (patient/surgeon), instruments, and personal protective equipment. DISCUSSION: Work-related MSK conditions are common among orthopaedic surgeons. Greater awareness of potential workplace-related hazards and conditions is needed to address and mitigate negative MSK health effects on orthopaedic surgeons.

Tibial torsion correlates with talar morphology.

BACKGROUND: There is limited literature on axial rotation of the ankle or variations in anatomy of the talus. We aim to evaluate the rotational profile of the distal tibia and its relationship to talus morphology, radiographic foot-type, and tibiotalar tilt in arthritic ankles. METHODS: Preoperative imaging was reviewed in 173 consecutive patients with ankle arthritis. CT measurements were used to calculate tibial torsion and the talar neck-body angle (TNBA). Tibiotalar tilt and foot-type were measured on weightbearing plain radiographs. RESULTS: Measurements indicated mean external tibial torsion of 29.2±9.1˚ and TNBA of 35.2±7.5˚ medial. Tibiotalar tilt ranged from 48˚ varus to 23.5˚ valgus. A moderate association between increasing external tibial torsion and decreasing TNBA was found (ρ=-0.576, p<.0001). Weak relationships were found between external tibial torsion and varus tibiotalar tilt (ρ=-0.239, p=.014) and plantarflexion of the talo-first metatarsal angle (ρ=-0.218, p<.025). CONCLUSION: We observed a statistically significant correlation between tibial torsion and morphology of the talus, tibiotalar tilt, and first ray plantarflexion. This previously unreported association may provide information regarding the development of foot and ankle deformity and pathology. LEVEL OF EVIDENCE: Level III.

Assessing Taper Geometry, Head Size, Head Material, and Their Interactions in Taper Fretting Corrosion of Retrieved Total Hip Arthroplasty Implants.

BACKGROUND: Decreased fretting and corrosion damage at the taper interface of retrieved ceramic-on-polyethylene total hip arthroplasty (THA) implants has been consistently reported; however, resultant fretting corrosion as a function of femoral head size and taper geometry has not been definitively explained. METHODS: Eight cohorts were defined from 157 retrieved THA implants based on femoral head composition (n = 95, zirconia-toughened alumina, ZTA vs n = 62, cobalt-chromium alloy, CoCr), head size (n = 56, 32mm vs n = 101, 36mm), and taper geometry (n = 84, 12/14 vs n = 73, V40). THA implants were evaluated and graded for taper fretting and corrosion. Data were statistically analyzed, including via a 23 factorial modeling. RESULTS: Factorial-based analysis indicated the significant factors related to both resultant (summed) fretting and corrosion damage were head material and taper geometry; head material-taper geometry interaction was also a significant factor in resultant corrosion damage. Lower rates of moderate-to-severe fretting and corrosion damage were exhibited on ZTA heads (ZTA = 13%, CoCr = 38%), smaller heads (32mm = 18%, 36mm = 26%), and 12/14 tapers (12/14 = 13%, V40 = 35%). ZTA+32mm heads demonstrated the lowest rates of moderate-to-severe fretting and corrosion damage (12/14 = 2%, V40 = 7%), whereas CoCr heads with V40 tapers demonstrated the greatest rates of moderate-to-severe damage (32mm = 47%, 36mm = 59%). CONCLUSION: In this series, retrieved implants with ZTA, 32-mm heads paired with 12/14 tapers exhibited lower rates of moderate-to-severe damage. Factorial analysis showed head material, taper geometry, and their interactions were the most significant factors associated with resultant damage grades. Isolating implant features may provide additional information regarding factors leading to fretting and corrosion damage in THA. LEVEL OF EVIDENCE: IV (case series).

Metabolomic Profiling in the Characterization of Degenerative Bone and Joint Diseases.

Osteoarthritis and inflammatory arthropathies are a cause of significant morbidity globally. New research elucidating the metabolic derangements associated with a variety of bone and joint disorders implicates various local and systemic metabolites, which further elucidate the underlying molecular mechanisms associated with these destructive disease processes. In osteoarthritis, atty acid metabolism has been implicated in disease development, both locally and systemically. Several series of rheumatoid arthritis patients have demonstrated overlapping trends related to histidine and glyceric acid, while other series showed similar results of increased cholesterol and glutamic acid. Studies comparing osteoarthritis and rheumatoid arthritis reported elevated gluconic acid and glycolytic- and tricarboxylic acid-related substrates in patients with osteoarthritis, while lysosphingolipids and cardiolipins were elevated only in patients with rheumatoid arthritis. Other bone and joint disorders, including osteonecrosis, intervertebral disc degeneration, and osteoporosis, also showed significant alterations in metabolic processes. The identification of the molecular mechanisms of osteoarthritis and inflammatory arthropathies via metabolomics-based workflows may allow for the development of new therapeutic targets to improve the quality of life in these patient populations.

Surgical Management of Triquetral Osteoid Osteoma with Adjunct Tetracycline for Intraoperative Visualization: A Case Report.

CASE: We report the case of a 15-year-old male patient presenting with persistent wrist pain after surgical treatment of a triquetral osteoid osteoma. The patient was found to have a persistent nidus. These tumors are difficult to observe intraoperatively or through fluoroscopy, limiting adequate resection and resulting in continued pain. CONCLUSION: The nidus was excised successfully through an unusual technique using tetracycline for intraoperative identification. The patient remains asymptomatic without recurrence at 31 months postoperative. Difficulties visualizing and removing carpal lesions leading to recurrence are described.

Analysis of Retrieved Unicompartmental Knee Implants and Tissue: Third-Body Wear as a Potential Contributor to Progression of Arthritis to Adjacent Compartments.

Unicompartmental knee arthroplasty (UKA) for the treatment of single-compartment osteoarthritis has been associated with polyethylene wear and progression of osteoarthritis into adjacent compartments, leading to revision. In this study, damage and clinical failure modes of retrieved UKA implants were investigated and protein expression profiles between articular cartilage adjacent to UKA and primary osteoarthritic cartilage were compared. Fifty retrieved UKA implants were analyzed for various damage. Records review and radiographic analysis were performed to collect clinical data and implant characteristics. Cartilage harvested from revision UKA and primary total knee arthroplasty surgeries was characterized with a proteome profiling array detecting levels of 36 different cytokines, chemokines, and acute phase inflammatory proteins. Progression of osteoarthritis (n=18, 36%) and component loosening (n=17, 34%) were the most common reasons for revision. Liners exhibited the highest frequency of damage modes. Progression of arthritis positively correlated with radiographic presence of extruded bone cement and burnishing of liner components. A protein-level profile between revision UKA and primary total knee arthroplasty cartilage showed 12 differentially expressed cytokines. Failure of UKA may be secondary to the effects of wear debris particulate migration into the adjacent compartment, suggesting an additional pathway of cartilage damage manifesting as traditional clinical symptoms. [Orthopedics. 2019; 42(3):149-157.].

Does Taper Design Affect Taper Fretting Corrosion in Ceramic-on-Polyethylene Total Hip Arthroplasty? A Retrieval Analysis.

BACKGROUND: Ceramic-on-polyethylene (CoP) implants have exhibited lower fretting and corrosion scores than metal-on-polyethylene implants. This study aims at investigating the effect of taper design on taper corrosion and fretting in modular CoP total hip arthroplasty (THA) systems. METHODS: Under an institutional review board--approved protocol, a query of an implant retrieval library from 2002 to 2017 identified 120 retrieved CoP THA systems with zirconia toughened alumina femoral heads. Femoral stem trunnions were visually evaluated and graded for fretting, corrosion, and damage at the taper interface. Medical records were reviewed for patient demographics and implant characteristics. Data were statistically analyzed using Spearman correlation and rank-sum tests with a Dunn's post hoc test, with a significance level of α = 0.05. RESULTS: Four different taper designs were evaluated: 11/13 (n = 18), 12/14 (n = 53), 16/18 (n = 21), and V40 (n = 28). There were no statistically significant demographic differences between taper groups for duration of implantation, laterality, patient age, and patient sex, but patients with 16/18 tapers had a higher body mass index than V40 tapers (P = .012). Duration of implantation had a weak positive correlation with both trunnion fretting (ρ = 0.224, P = .016) and corrosion (ρ = 0.253, P = .006). Summed fretting and corrosion scores were significantly greater on the V40 and 16/18 tapers compared with the 12/14 tapers (all P ≤ .001). CONCLUSION: Taper fretting and corrosion were observed in CoP THA implants and were greatest with V40 and 16/18 tapers and lowest with 12/14 tapers. Differences in taper design characteristics may lead to greater micromotion at the taper-head interface, leading to increased fretting and corrosion.

Fretting and Corrosion Damage of Retrieved Dual-Mobility Total Hip Arthroplasty Systems.

BACKGROUND: Dual-mobility (DM) total hip arthroplasty (THA) systems are designed to increase stability while potentially avoiding problems associated with large femoral heads. Complications of these systems are not yet fully understood. This study aims at characterizing in vivo performance of DM hip systems and assessing modes of clinical failure. METHODS: Under an institutional review board-approved implant retrieval protocol, 18 DM THA systems from 17 patients were included. Implants were graded at the head-neck junction for fretting and corrosion based on the system of Goldberg et al. Components were also macroscopically examined for different damage modes. Demographics and surgical data were collected from medical records, and radiographs were assessed for component positioning. Data were analyzed through Spearman rank-order correlation and Mann-Whitney U-tests, with α = 0.05. RESULTS: The average length of implantation was 13.4 months with mild to moderate fretting corrosion damage. Polyethylene (PE) liners exhibited edge deformation, scratching, and pitting damage. Metallic components exhibited burnishing and scratching damage. Summed fretting and corrosion scores were strongly correlated (ρ = 0.967, P < .0001). Summed corrosion score was moderately correlated with presence of embedding on the PE liner (ρ = 0.690, P = .017). PE liner abrasion and edge deformation of the femoral stem taper were moderately positively correlated (ρ = 0.690, P = .017). Fretting and corrosion damage were not significantly correlated with patient demographics or radiographic positioning of implants. There were no differences in scores between modular and monoblock designs. CONCLUSION: These findings demonstrate that dual-mobility THA systems may be susceptible to the same fretting and corrosion damage observed in traditional modular THA systems. Future studies are needed to confirm these results and clinical significance.