ABSTRACT
Internet of Things applications based on backscatter radio principles have appeared to address the limitations of high cost and high power consumption. While radio-frequency identification (RFID) sensor nodes are among the most commonly utilized state-of-the-art technologies, their range for passive implementations is typically short and well below 10 m being impractical for "rugged" applications where approaching the tag at such proximity, is not convenient or safe. In this work, we propose a long-range "zero interception" ambient backscatter (LoRAB) communication system relying on low power sensor (tag) deployments. Without employing a dedicated radio transmission, our technology enables the "zero interception" communication of the tags with portable receivers over hundreds of meters. This enables low-cost and low-power communications across a wide range of missions by using chirp spread spectrum (CSS) modulation on ambient FM signals. A laboratory prototype exploiting commercial components (laptops, DAQ, software-defined radios (SDR) platform) have demonstrated the potential by achieving 130 m tag-to-reader distance for a low bit rate of 88 bps with the modulator current consumption at around 103 nA.
ABSTRACT
A triple-band single-layer rectenna for outdoor RF energy applications is introduced in this paper. The proposed rectenna operates in the frequency bands of LoRa, GSM-1800, and UMTS-2100 networks. To obtain a triple-band operation, a modified E-shaped patch antenna is used. The receiving module (antenna) of the rectenna system is optimized in terms of its reflection coefficient to match the RF-to-DC rectifier. The final geometry of the proposed antenna is derived by the application of the Moth Search Algorithm and a commercial electromagnetic solver. The impedance matching network of the proposed system is obtained based on a three-step process, including the minimization of the reflection coefficient versus frequency, as well as the minimization of the reflection coefficient variations and the maximization of the DC output voltage versus RF input power. The proposed RF-to-DC rectifier is designed based on the Greinacher topology. The designed rectenna is fabricated on a single layer of FR-4 substrate. Measured results show that our proposed rectenna can harvest RF energy from outdoor (ambient and dedicated) sources with an efficiency of greater than 52%.
ABSTRACT
In this paper, the far-field energy harvesting system for self-sustainable wireless autonomous sensor application is presented. The proposed autonomous sensor system consists of a wireless power supplier (active antenna) and far-field energy harvesting technology-enabled autonomous battery-less sensors. The wireless power supplier converts solar power to electromagnetic power in order to transfer power to multiple autonomous sensors wirelessly. The autonomous sensors have far-field energy harvesters which convert transmitted RF power to voltage regulated DC power to power-on the sensor system. The hybrid printing technology was chosen to build the autonomous sensors and the wireless power suppliers. Two popular hybrid electronics technologies (direct nano-particle printing and indirect copper thin film printing techniques) are discussed in detail.
ABSTRACT
A new electrically small antenna with size ka = 0.415 is presented, fabricated and measured in this work. This is intrinsically matched to 50 Ω, has omni-directional and linear-polarized radiation pattern in the horizontal plane with maximum directivity of 1.75 dBi and simulated radiation efficiency of 93%. The antenna in combination with a low-complex and co-planar rectifier with one single diode forms a high efficient and sensitive electrically small rectenna with ka = 0.53 at 868 MHz (UHF RFID-band in Europe). The latter has measured efficiency 22.5% for -19 dBm power input and sensitivity of -44 dBm (or equivalently 0.00028 µW/cm2 power density), while at 2.25 µW/cm2 is able to supply continuously, i.e., without a boost converter or use of any energy tank, a small electrical device with 118 µW. In order to increase the dc output voltage and the delivered dc power to the load for lower power density levels, rectenna-array configuration is exploited. Application to batteryless, backscatter wireless sensor node powering is discussed. Specifically, for a power density of 0.1237 µW/cm2 the RF energy harvesting system delivers 172 µW at 2.85 V every 22.5 s.
ABSTRACT
The detailed design considerations for the printed RFID-based sensor system is presented in this paper. Starting from material selection and metallization method, this paper discusses types of RFID-based sensors (single- & dual-tag sensor topologies), design procedures, and performance evaluation methods for the wireless sensor system. The electrical properties of the paper substrates (cellulose-based and synthetic papers) and the silver nano-particle-based conductive film are thoroughly characterized for RF applications up to 8 GHz. The reported technology could potentially set the foundation for truly “green”, low-cost, scalable wireless topologies for autonomous Internet-of-Things (IoT), bio-monitoring, and “smart skin” applications.
ABSTRACT
With recent advances at X-ray microcomputed tomography (µCT) synchrotron beam lines, it is now possible to study pore-scale flow in porous rock under dynamic flow conditions. The collection of four-dimensional data allows for the direct 3-D visualization of fluid-fluid displacement in porous rock as a function of time. However, even state-of-the-art fast-µCT scans require between one and a few seconds to complete and the much faster fluid movement occurring during that time interval is manifested as imaging artifacts in the reconstructed 3-D volume. We present an approach to analyze the 2-D radiograph data collected during fast-µCT to study the pore-scale displacement dynamics on the time scale of 40 ms which is near the intrinsic time scale of individual Haines jumps. We present a methodology to identify the time intervals at which pore-scale displacement events in the observed field of view occur and hence, how reconstruction intervals can be chosen to avoid fluid-movement-induced reconstruction artifacts. We further quantify the size, order, frequency, and location of fluid-fluid displacement at the millisecond time scale. We observe that after a displacement event, the pore-scale fluid distribution relaxes to (quasi-) equilibrium in cascades of pore-scale fluid rearrangements with an average relaxation time for the whole cascade between 0.5 and 2.0 s. These findings help to identify the flow regimes and intrinsic time and length scales relevant to fractional flow. While the focus of the work is in the context of multiphase flow, the approach could be applied to many different µCT applications where morphological changes occur at a time scale less than that required for collecting a µCT scan.
