Correlating the Diffusion of Water to Performance in Model Reverse Osmosis Polyamides with Controlled Crosslink Densities.

We systematically reduce the cross-link density of a PA network based on m-phenylene diamine by substituting a fraction of the trifunctional trimesoyl chloride cross-linking agent with a difunctional isophthaloyl analog that promotes chain extension, in order to elucidate robust design cues for improving the polyamide (PA) separation layer in reverse osmosis (RO) membranes for desalination. Thin films of these model PA networks are fully integrated into a composite membrane and evaluated in terms of their water flux and salt rejection. By incorporating 15 mol % of the difunctional chain extender, we reduce the cross-link density of the network by a factor of two, which leads to an 80 % increase in the free or unreacted amine content. The resulting swelling of the PA network in liquid water increases by a factor of two accompanied by a 30 % increase in the salt passage through the membrane. Surprisingly, this leads to a 30 % decrease in the overall permeance of water through the membrane. This conundrum is resolved by quantifying the microscopic diffusion coefficient of water inside the PA network with quasi-elastic neutron scattering. In the highest and lowest cross-link density networks, water shows strong signatures of confined diffusion. At short length scales, the water exhibits a translational diffusion that is consistent with the jump-diffusion mechanism. This translational diffusion coefficient is approximately five times slower in the lowest cross-linked density network, consistent with the reduced water permeance. This is interpreted as water molecules interacting more strongly with the increased free amine content. Over longer length scales the water diffusion is confined, exhibiting mobility that is independent of length scale. The length scales of confinement from the quasi-elastic neutron scattering experiments at which this transition from confined to translational diffusion occurs is on the order of (5 to 6) Å, consistent with complementary X-ray scattering, small angle neutron scattering, and positron annihilation lifetime spectroscopy measurements. The confinement appears to come from heterogeneities in the average inter-atomic distances, suggesting that diffusion occurs by water bouncing between chains and occasionally sticking to the polar functional groups. The results obtained here are compared with similar studies of water diffusion through both rigid porous silicates and ion exchange membranes, revealing robust design cues for engineering high-performance RO membranes.

Hierarchical Nature of Nanoscale Porosity in Bone Revealed by Positron Annihilation Lifetime Spectroscopy.

Bone is a hierarchical material primarily composed of collagen, water, and mineral that is organized into discrete molecular, nano-, micro-, and macroscale structural components. In contrast to the structural knowledge of the collagen and mineral domains, the nanoscale porosity of bone is poorly understood. In this study, we introduce a well-established pore characterization technique, positron annihilation lifetime spectroscopy (PALS), to probe the nanoscale size and distribution of each component domain by analyzing pore sizes inherent to hydrated bone together with pores generated by successive removal of water and then organic matrix (including collagen and noncollagenous proteins) from samples of cortical bovine femur. Combining the PALS results with simulated pore size distribution (PSD) results from collagen molecule and microfibril structure, we identify pores with diameter of 0.6 nm that suggest porosity within the collagen molecule regardless of the presence of mineral and water. We find that water occupies three larger domain size regions with nominal mean diameters of 1.1, 1.9, and 4.0 nm-spaces that are hypothesized to associate with intercollagen molecular spaces, terminal segments (d-spacing) within collagen microfibrils, and interface spacing between collagen and mineral structure, respectively. Subsequent removal of the organic matrix determines a structural pore size of 5-6 nm for deproteinized bone-suggesting the average spacing between mineral lamella. An independent method to deduce the average mineral spacing from specific surface area (SSA) measurements of the deproteinized sample is presented and compared with the PALS results. Together, the combined PALS and SSA results set a range on the mean mineral lamella thickness of 4-8 nm.

In Vitro Characterization of the Biomimetic Properties of Poly(dimethylsiloxane) To Simulate Oral Drug Absorption.

The potential use of poly(dimethylsiloxane) (PDMS) as an in vitro biomimetic analogue of the passive drug absorption process in the human gastrointestinal tract (GI) is assessed. PDMS is biomimetic because of similarities in small molecule transport, such as mechanism, ionization selectivity, lipophilicity. Nine molecular probes are used to evaluate the transport pathways and properties used to predict human oral absorption rates. The transport pathways through PDMS (bulk/pore) are analogous to transcellular (TCDT) and paracellular (PCDT) drug transport pathways. PDMS PCDT is assessed using positronium annihilation lifetime spectroscopy (PALS) and partition experiments; TCDT using diffusion and partition experiments. PALS determined that PDMS pores were uniform (D ∼ 0.85 nm), isolated, and void volume was unaffected by drug accumulation after equilibrium partitioning. Therefore, there is no PCDT or convective flow through PDMS. A strong linear correlation exists between predicted octanol-water partition coefficients and PDMS partition coefficients (LogKPDMS = 0.736 × LogPO-W - 0.971, R2 = 0.981). The pH-partition hypothesis is confirmed in PDMS using ibuprofen over pH 2-12. Diffusivity through PDMS is a function of lipophilicity and polar surface area K × DPDMS = 4.46 × 10-8 × e2.91×LogKPDMS(R2 = 0.963) and [Formula: see text] (R2 = 0.973). Varying the mass% of curing agent changed the lipophilicity and diffusivity (p < 0.02), but not practically (K × D = 2.23 × 10-5cm2s-1 vs 2.60 × 10-5cm2s-1), and does affect elastic modulus (3.2% = 0.3 MPa to 25% = 3.2 MPa).

High thermal conductivity in electrostatically engineered amorphous polymers.

High thermal conductivity is critical for many applications of polymers (for example, packaging of light-emitting diodes), in which heat must be dissipated efficiently to maintain the functionality and reliability of a system. Whereas uniaxially extended chain morphology has been shown to significantly enhance thermal conductivity in individual polymer chains and fibers, bulk polymers with coiled and entangled chains have low thermal conductivities (0.1 to 0.4 W m-1 K-1). We demonstrate that systematic ionization of a weak anionic polyelectrolyte, polyacrylic acid (PAA), resulting in extended and stiffened polymer chains with superior packing, can significantly enhance its thermal conductivity. Cross-plane thermal conductivity in spin-cast amorphous films steadily grows with PAA degree of ionization, reaching up to ~1.2 W m-1 K-1, which is on par with that of glass and about six times higher than that of most amorphous polymers, suggesting a new unexplored molecular engineering strategy to achieve high thermal conductivities in amorphous bulk polymers.

The assessment of pore connectivity in hierarchical zeolites using positron annihilation lifetime spectroscopy: instrumental and morphological aspects.

Recent studies demonstrated the power of positron annihilation lifetime spectroscopy (PALS) to characterise the connectivity and corresponding effectiveness of hierarchical pore networks in zeolites. This was based on the fractional escape of ortho-positronium (Ps), formed within the micropore framework, to vacuum. To further develop this technique, here we assess the impact of the positron implantation energy and of the zeolite crystal size and the particle morphology. Conventional measurements using fast positrons and beam measurements applying moderated positrons both readily distinguish purely microporous ZSM-5 zeolites comprised of single crystals or crystal aggregates. Unlike beam measurements, however, conventional measurements fail to discriminate model hierarchical zeolites with open or constricted mesopore architectures. Several steps are taken to rationalise these observations. The dominant contribution of Ps diffusion to the PALS response is confirmed by capping the external surface of the zeolite crystals with tetraethylorthosilicate, which greatly enhances the sensitivity to the micropore network. A one-dimensional model is constructed to predict the out-diffusion of Ps from a zeolite crystal, which is validated experimentally by comparing coffin-shaped single crystals of varying size. Calculation of the trends expected on the application of fast or moderated positrons indicates that the distinctions in the initial distribution of Ps at the crystal level cannot explain the limited sensitivity of the former to the mesopore architecture. Instead, we propose that the greater penetration of fast positrons within the sample increases the probability of Ps re-entry from intercrystalline voids into mesopores connected with the external surface of zeolite crystals, thereby reducing their fractional escape.

Water sensitivity in Zn4O-based MOFs is structure and history dependent.

Moisture can cause irreversible structural collapse in metal-organic frameworks (MOFs) resulting in decreased internal surface areas and pore volumes. The details of such structural collapse with regard to pore size evolution during degradation are currently unknown due to a lack of suitable in situ probes of porosity. Here we acquire MOF porosity data under dynamic conditions by incorporating a flow-through system in tandem with positronium annihilation lifetime spectroscopy (PALS). From the decrease in porosity, we have observed an induction period for water degradation of some Zn4O-based MOFs that signals much greater stability than commonly believed to be possible. The sigmoidal trend in the degradation curve of unfunctionalized MOFs caused by water vapor has been established from the temporal component of pore size evolution as characterized by in situ PALS. IRMOF-3 is found to degrade at a lower relative humidity than MOF-5, a likely consequence of the amine groups in the structure, although, in contrast to MOF-5, residual porosity remains. The presence of an induction period, which itself depends on previous water exposure of the sample (history dependence), and sigmoidal temporal behavior of the moisture-induced degradation mechanism of MOFs was also verified using powder X-ray diffraction analysis and ex situ gas adsorption measurements. Our work provides insight into porosity evolution under application-relevant conditions as well as identifying chemical and structural characteristics influencing stability.

High thermal conductivity in amorphous polymer blends by engineered interchain interactions.

Thermal conductivity is an important property for polymers, as it often affects product reliability (for example, electronics packaging), functionality (for example, thermal interface materials) and/or manufacturing cost. However, polymer thermal conductivities primarily fall within a relatively narrow range (0.1-0.5 W m(-1) K(-1)) and are largely unexplored. Here, we show that a blend of two polymers with high miscibility and appropriately chosen linker structure can yield a dense and homogeneously distributed thermal network. A sharp increase in cross-plane thermal conductivity is observed under these conditions, reaching over 1.5 W m(-1) K(-1) in typical spin-cast polymer blend films of nanoscale thickness, which is approximately an order of magnitude larger than that of other amorphous polymers.

Effect of pore structure of nanometer scale porous films on the measured elastic modulus.

The impact of pore structure of nanoporous films on the measured elastic modulus is demonstrated for silica-based nanoporous low-k films that are fabricated using an alternative manufacturing sequence which allows a separate control of porosity and matrix properties. For this purpose, different experimental techniques for measuring the elastic properties were compared, including nanoindentation, laser-induced surface acoustic wave spectroscopy (LAwave), and ellipsometric porosimetry (EP). The link between the elastic response of these nanoporous materials and their internal pore structure was investigated using positronium annihilation lifetime spectroscopy (PALS), EP, and diffusion experiments. It is shown that the absolute value of the Berkovich indentation modulus is very sensitive to the local pore structure and stiffness of the substrate and can be influenced by densification and/or anisotropic elasticity upon indentation, while on the other hand spherical indentation results are less sensitive to the local pore structure. The comparison of Berkovich and spherical indentation results combined with finite element simulations can potentially reveal changes in the internal structure of the film. For nanoporous films with porosity above the percolation threshold, the elastic modulus results obtained with LAwave and EP agree very well with spherical indentation results. On the other hand, below the percolation threshold, the elastic modulus values determined by these techniques deviate from the spherical indentation results. This was explained in terms of specific technique related effects that appear to be sensitive to the specific arrangement and morphology of the pores.

Interpenetration, porosity, and high-pressure gas adsorption in Zn4O(2,6-naphthalene dicarboxylate)3.

Microporous coordination polymers (MCPs) have emerged as strong contenders for adsorption-based fuel storage and delivery in large part because of their high specific surface areas. The strategy of increasing surface area by increasing organic linker length has shown only sporadic success; as demonstrated by many members of the iconic Zn4O-based IRMOF series, for example, accessible porosity is often limited by interpenetration or pore collapse upon guest removal. In this work, we focus on Zn4O(ndc)3 (IRMOF-8, ndc = 2,6-naphthalene dicarboxylate), which exhibits typical surface areas of only 1000-2000 m(2)/g even though a surface area of more than 4000 m(2)/g is expected from geometric analysis of the originally reported crystal structure. We recently showed that a high surface area could be produced with zinc and ndc by room-temperature synthesis followed by activation with flowing supercritical CO2. In this work, we investigate in detail the porosity of both the low- and high-surface-area materials. Positron annihilation lifetime spectroscopy (PALS) is used to show that the low-surface-area material suffers from near-complete interpenetration, explaining why traditional synthetic routes have failed to yield materials with the expected porosity. Furthermore, the high-pressure hydrogen and methane sorption properties of noninterpenetrated Zn4O(ndc)3 are examined, and PALS is used to show that pore filling is not operative during room-temperature CH4 sorption even at pressures approaching 100 bar. These results provide insight into how gas adsorbs in high-surface-area materials at high pressure and reinforce previous contentions that increasing surface area alone is not sufficient for the simultaneous optimization of deliverable gravimetric and volumetric gas uptake in MCPs.

Evidence of Positronium Bloch states in porous crystals of Zn4O-coordination polymers.

Positronium (Ps) is shown to exist in a delocalized state in self-assembled metalorganic crystals that have large 1.3-1.5 nm cell sizes. Belonging to a class of materials with record high accessible specific surface areas, these highly porous crystals are the first to allow direct probing with simple annihilation lifetime techniques of the transport properties of long-lived triplet Ps in what is hypothesized to be a Bloch state. Delocalized Ps has unprecedented (high) Ps mobility driven primarily by weak phonon scattering with unusual and profound consequences on how Ps probes the lattice.

Reconciling the discrepancies between crystallographic porosity and guest access as exemplified by Zn-HKUST-1.

There are several compounds for which there exists a disconnect between porosity as predicted by crystallography and porosity measured by gas sorption analysis. In this paper, the Zn-based analogue of Cu(3)(btc)(2) (HKUST-1), Zn(3)(btc)(2) (Zn-HKUST-1; btc = 1,3,5-benzenetricarboxylate) is investigated. Conventional analysis of Zn-HKUST-1 by powder X-ray diffraction and gas sorption indicates retention of crystalline structure but negligible nitrogen uptake at 77 K. By using positron annihilation lifetime spectroscopy, a densified surface layer preventing the entry of even small molecular species into the crystal framework is revealed. The material is shown to have inherent surface instability after solvent removal, rendering it impermeable to molecular guests irrespective of handling and processing methods. This previously unobserved surface instability may provide insight into the failure of other microporous coordination polymers to exhibit significant porosity despite crystal structures indicative of regular, interconnected, microporous networks.

Role of molecular architecture on the vitrification of polymer thin films.

We show that thin film star-shaped macromolecules exhibit significant differences in their average vitrification behavior, in both magnitude and thickness dependence, from their linear analogs. This behavior is dictated by a combination of their functionality and arm length. Additionally, the glass transition temperature at the free surface of a star-shaped molecule film may be higher than that of the interior, in contrast to their linear analogs where the opposite is true. These findings have implications for other properties, due largely to the origins, entropic, of this behavior.