Laser Ablation of Silicon Nanoparticles and Their Use in Charge-Coupled Devices for UV Light Sensing via Wavelength-Shifting Properties.

This study explores the controlled laser ablation and corresponding properties of silicon nanoparticles (Si NP) with potential applications in ultraviolet (UV) light sensing. The size distribution of Si NPs was manipulated by adjusting the laser scanning speed during laser ablation of a silicon target in a styrene solution. Characterization techniques, including transmission electron microscopy, Raman spectroscopy, and photoluminescence analysis, were employed to investigate the Si NP structural and photophysical properties. Si NP produced at a laser scanning speed of 3000 mm/s exhibited an average diameter of ~4 nm, polydispersity index of 0.811, and a hypsochromic shift in the Raman spectrum peak position. Under photoexcitation at 365 nm, these Si NPs emitted apparent white light, demonstrating their potential for optoelectronic applications. Photoluminescence analysis revealed biexponential decay behavior, suggesting multiple radiative recombination pathways within the nanoscale structure. Furthermore, a thin film containing Si NP was utilized as a passive filter for a 2nd generation CCD detector, expanding the functionality of the non-UV-sensitive detectors in optics, spectrometry, and sensor technologies.

Recycling of Wind Turbine Blades into Microfiber Using Plasma Technology.

As the industry develops and energy demand increases, wind turbines are increasingly being used to generate electricity, resulting in an increasing number of obsolete turbine blades that need to be properly recycled or used as a secondary raw material in other industries. The authors of this work propose an innovative technology not yet studied in the literature, where the wind turbine blades are mechanically shredded and micrometric fibers are formed from the obtained powder using plasma technologies. As shown by SEM and EDS studies, the powder is composed of irregularly shaped microgranules and the carbon content in the obtained fiber is lower by up to seven times compared with the original powder. Meanwhile, the chromatographic studies show that no hazardous to the environment gases are formed during the fiber production. It is worth mentioning that this fiber formation technology can be one of the additional methods for recycling wind turbine blades, and the obtained fiber can be used as a secondary raw material in the production of catalysts, construction materials, etc.

Thermal plasma potential to remediate soil contaminated with diesel.

Petroleum hydrocarbons (PHCs) are recognized as one of the major soil contaminants causing negative environmental impact. Thereby, PHCs remediation from the soil is essential. Hence, this experimental study aimed to assess the potential of thermal water vapor and air plasmas to remediate soil contaminated with habitually used PHCs - diesel. The impact of contaminant content in the soil on the remediation process also was estimated. The results of this research demonstrated that 99.9% contaminant removal efficiency was received proceeding diesel contaminated soil remediation in the environment of the thermal plasma in defiance of whether water vapor or air was employed as a plasma-forming gas. Moreover, the soil's contaminant content (80-160 g/kg) did not influence its' removal efficiency. The soil de-pollution process also caused the decomposition of the soils' natural carbon reserves since carbon content decreased from an initial 9.8 wt% in the clean soil to 3-6 wt% in the remediated soil. Furthermore, PHCs - diesel was decomposed into producer gas mainly consisting of H2, CO (also known as synthesis gas) and CO2. Thus, the thermal plasma offers a way not only to de-pollute the soil but also to reuse the PHCs present in the soil by breaking it down into gaseous products that can further be used to meet human needs.

Biomass gasification to syngas in thermal water vapor arc discharge plasma.

This study investigated biomass (wood pellets) gasification to syngas using direct current (DC) thermal arc plasma at atmospheric pressure. Water vapor was used as a main gasifying agent and a plasma-forming gas. The biomass gasification system was quantified in terms of the producer gas composition, the tar content, the H2/CO ratio, the carbon conversion efficiency, the energy conversion efficiency and the specific energy requirements. It was found that the gasification performance efficiency was highest at the water vapor-to-biomass ratio of 0.97. The producer gas was mostly composed of H2 (43.86 vol.%) and CO (30.93 vol.%), giving the H2/CO ratio of 1.42 and the LHV of 10.23 MJ/Nm3. However, high content of tars of 13.81 g/Nm3 was obtained in the syngas. The yield of H2 and CO was 48.31% and 58.13%, respectively, with the highest producer gas yield of 2.42 Nm3/kg biomass. The carbon conversion efficiency and the energy conversion efficiency were 100% and 48.83%, respectively, and the production of 1 kg of syngas required 1.78 kWh of electric energy input. Finally, the obtained results were compared with different plasma methods, including plasma-assisted application coupled with conventional gasification.

Treatment of diesel-contaminated soil using thermal water vapor arc plasma.

Soil pollution with petroleum-based fuels is a serious issue causing environmental problems. Recently, the use of plasma technologies for soil remediation has shown an interest and great potential. The remediation process can be performed in a fast timeframe without adding supplementary chemical reagents or without additional pre-treatment of the polluted soil. As a result, the use of plasma enables to obtain highly effective degradation of pollutants. Thus, in the present experimental research, diesel fuel removal from contaminated soil by utilizing thermal water vapor arc plasma was investigated. It was found that increased concentration of diesel fuel in the soil raised carbon and hydrogen concentrations in the soil. Moreover, soil surface morphology was modified by causing the formation of bigger agglomerates. It was also determined that after the plasma treatment process, soil grains became akin in size and structure to clean soil grains. A complete desorption of carbon, which came from diesel fuel to the soil, and a slight decomposition of organic carbon present in the soil were observed during the soil remediation process. Thermogravimetric analysis showed that regardless of the diesel fuel concentration in the soil, four stages of mass loss were observed: moisture loss, vaporization, and combustion of diesel fuel as well as reduction of volatiles and char in the soil. Producer gas analysis indicated that during soil remediation diesel fuel was mainly converted to synthesis gas, i.e., a mixture of H2, CO, and CO2. Moreover, the decomposition of diesel fuel and the formation of synthesis gas depended on the amount of pollutant in the soil. According to the obtained results, thermal water vapor arc plasma was able to completely remove diesel fuel from polluted soil in the form of synthesis gas with no significant influence on soil's properties.

Energy recovery from waste glycerol by utilizing thermal water vapor plasma.

Glycerol, considered as a waste feedstock resulting from biodiesel production, has received much attention in recent years due to its properties, which offer to recover energy. The aim of this study was to investigate the use of a thermal water vapor plasma for waste (crude) glycerol conversion to synthesis gas, or syngas (H2 + CO). In parallel of crude glycerol, a pure glycerol (99.5%) was used as a reference material in order to compare the concentrations of the formed product gas. A direct current (DC) arc plasma torch stabilized by a mixture of argon/water vapor was utilized for the effective glycerol conversion to hydrogen-rich synthesis gas. It was found that after waste glycerol treatment, the main reaction products were gases with corresponding concentrations of H2 50.7%, CO 23.53%, CO2 11.45%, and CH4 3.82%, and traces of C2H2 and C2H6, which concentrations were below 0.5%. The comparable concentrations of the formed gas products were obtained after pure glycerol conversion-H2 46.4%, CO 26.25%, CO2 11.3%, and CH4 4.7%. The use of thermal water vapor plasma producing synthesis gas is an effective method to recover energy from both crude and pure glycerol. The performance of the glycerol conversion system was defined in terms of the produced gas yield, the carbon conversion efficiency, the cold gas efficiency, and the specific energy requirements.