Effect of immediate dentin sealing and temporary cement removal on bond strength of resin cements to dentin / Efeito do selamento dentinário imediato e da remoção do cimento provisório na resistência de união de cimentos resinosos à dentina

Objective: To evaluate the influence of immediate dentin sealing (IDS) and mechanical methods for removing the temporary cement on the bond strength between dentin and resin cements. Material and Methods: Bovine incisors were ground until dentin exposure and divided according to two factors: "dentin surface treatment"' - cleaning with manual dental excavator (DE), with Robinson bristle brush and pumice paste (PP) or IDS application with Single Bond 2 (IDS/SB+PP) or Single Bond Universal (IDS/SBU+PP) plus cleaning with PP; and "resin cement" - Self-adhesive (RelyX U200) or conventional cement with self-etching adhesive (Multilink Automix). Simulating provisional restoration, acrylic resin plates were cemented onto the dentin surface (with or without IDS) with a non-eugenol temporary cement, and stored in distilled water (37 ºC; 7 days). The acrylic plates were removed, the dentin surface was cleaned (PP or DE), and starch tubes were positioned on the dentin where the resin cements were applied. After 24 h, the specimens were submitted to a microshear test (wire-loop method). Results: Two-way analysis of variance showed statistically significant influence of dentine surface treatments (p< 0.001) and resin cement (p= 0.001) in the bond strength values. The IDS/SBU+PP/U200 (7.24 MPa) and IDS/SBU+PP/MULTI (6.40 MPa) groups presented higher values when compared to cleaning with DE (DE/U200= 4.60 MPa; DE/MULTI= 1.45 MPa) and PP (PP/U200= 3.74 MPa; PP/MULTI= 3.14 MPa). Statistical difference was also found between the cements when dental excavator treatment was used (RelyX U200 ˃ Multilink Automix). The IDS/SBU+PP protocol presented a higher percentage of cohesive failures. The micrographs showed differences in dentin surface characteristics among the groups. Conclusion: Immediate dentin sealing increased the bond strength of the resin cements to dentin compared to mechanical cleaning only, regardless the resin cement. (AU)

Objetivo: Avaliar a influência do selamento dentinário imediato (IDS) e dos métodos mecânicos de remoção do cimento provisório na resistência de união entre dentina e cimentos resinosos. Materiais e Métodos: Incisivos bovinos foram desgastados até a exposição da dentina e divididos de acordo com dois fatores: "tratamento da superfície dentinária" - limpeza com cureta dentária manual (DE), com escova de cerdas Robinson e pasta de pedra-pomes (PP) ou aplicação de IDS com Single Bond 2 (IDS/SB +PP) ou Single Bond Universal (IDS/SBU+PP) mais limpeza com PP; e "cimento resinoso" - autoadesivo (RelyX U200) ou cimento convencional com adesivo autocondicionante (Multilink Automix). Simulando a restauração provisória, placas de resina acrílica foram cimentadas na superfície dentinária (com ou sem IDS) com um cimento provisório sem eugenol e armazenadas em água destilada (37 ºC; 7 dias). As placas de acrílico foram removidas, a superfície dentinária foi limpa (PP ou DE) e tubos de amido foram posicionados na dentina onde os cimentos resinosos foram aplicados. Após 24 h, os corpos-de-prova foram submetidos ao ensaio de microcisalhamento (método wire-loop). Resultados: A análise de variância de dois fatores mostrou influência estatisticamente significativa dos tratamentos de superfície dentinária (p< 0,001) e cimento resinoso (p= 0,001) nos valores de resistência de união. Os grupos IDS/SBU+PP/U200 (7,24 MPa) e IDS/SBU+PP/MULTI (6,40 MPa) apresentaram valores maiores quando comparados à limpeza com DE (DE/U200= 4,60 MPa; DE/MULTI= 1,45 MPa) e PP (PP/U200= 3,74 MPa; PP/MULTI= 3,14 MPa). Uma diferença estatística também foi encontrada entre os cimentos quando o tratamento com cureta dentária foi usado (RelyX U200 ˃ Multilink Automix). O protocolo IDS/SBU+PP apresentou maior percentual de falhas coesivas. As micrografias mostraram diferenças nas características da superfície dentinária entre os grupos. Conclusão: O selamento dentinário imediato aumentou a resistência de união dos cimentos resinosos à dentina em comparação com a limpeza mecânica apenas, independentemente do cimento resinoso.(AU)

Effect of zirconia surface treatment, resin cement and aging on the load-bearing capacity under fatigue of thin simplified full-contour Y-TZP restorations.

This study investigated the effect of zirconia surface treatment (air-abrasion with aluminum oxide or tribochemical silica coating) and aging on the fatigue behavior of thin monolithic Y-TZP (yttria-stabilized tetragonal zirconia polycrystal) restorations cemented with 2 types of resin cements, containing or not containing MDP, to a dentin-like substrate. Y-TZP ceramic (Zenostar T, diameter (Ø) 10 mm, 0.7 mm thick) and dentin-like discs (Ø 10 mm, 2.8 mm thick) were assigned into eight groups according to three factors: 'zirconia surface treatment' (aluminum oxide particles air-abrasion 'AO'; or tribochemical silica coating via silica-coated aluminum trioxide particles air-abrasion + silanization 'SC'); 'MDP-containing resin cement' (with: Panavia F2.0, 'MDP'; or without: Multilink Automix, 'nMDP'); and 'aging' (baseline; or aged - 'AG':12,000 thermal cycles + 60 days water storage). Y-TZP intaglio surface was conditioned and dentin-like substrate was etched with hydrofluoric acid prior to bonding. Aging was performed in half of the specimens before the fatigue testing (Staircase, 20 Hz; 250,000 cycles). Fractographic and topographic characteristics were analyzed by stereomicroscope and SEM. Prior to aging, no significant difference was found between the two surface treatments, irrespective to the cement. Samples bonded with resin cement containing MDP had a significant reduction in their fatigue failure load when Y-TZP was air-abraded with aluminum oxide particles and subjected to aging (MDP-AO = 2050.71A; MDP-AO/AG = 1756.67B). Other studied conditions were not affected by aging. Topographic images revealed a rougher surface for aluminum oxide air-abrasion. Fractography supports all failures as a radial crack starting at the Y-TZP intaglio surface. Bonded thin simplified Y-TZP restorations had a high load-bearing capacity, regardless of the studied factors. The MDP-containing resin cement applied on aluminum oxide air-abraded zirconia surface was not enough to maintain the fatigue performance after aging, while higher stability to aging was achieved by treating with the tribochemical silica coating method. When using MDP-free resin cement, the surface treatment and the aging did not impact the fatigue performance.