Shear Bond Strength of Orthodontic Brackets Bonded with Thermo-Cured Glass-Based Materials-An In Vitro Study.

The results of orthodontic therapy largely depend, among other factors, on the preparation of the tooth enamel itself and the choice of material used to bond orthodontic brackets. The aim of this in vitro study was to determine the shear bond strength (SBS) and adhesive remnant index (ARI) score of thermo-cured glass-ionomers on different pretreated enamel, in comparison with the commonly used composite cement. Three commercially available nano-ionomer or highly viscous glass-ionomer cements (EQUIA Forte® Fil, EQUIA Fil, Ketac Universal) and two types of compo-sites (Heliosit Orthodontic, ConTec Go!) were investigated in this study. The research involved two hundred human premolars. The teeth were cleaned and polished, then randomly divided into five groups according to the enamel preparation method and the type of material. The enamel was treated in three different ways: polyacrylic acid, phosphoric acid, 5% NaOCl + etching with phosphoric acid, and a control group without treatment. Glass-ionomer cement was thermo-cured with heat from a polymerization unit during setting. Statistical analysis was performed using a Chi-square test and one-way ANOVA for independent samples. Spearman's Rho correlation coefficient was used to examine the relationship. Regardless of the material type, the results indicated that the weakest bond between the bracket and tooth enamel was found in samples without enamel pretreatment. The majority of the materials stayed on the brackets in samples without enamel preparation, according to ARI scores. The study's findings demonstrated that the strength of the adhesion between the bracket and enamel is greatly influenced by enamel etching and glass-ionomer thermo-curing. Clinical investigations would be required to validate the outcomes.

The Effect of Chemical Degradation and Polishing on the Gloss of Composite Dental Materials.

This aim of this study was to investigate surface gloss changes of different composite dental materials after chemical degradation or polishing. Five different composites were used (Evetric, GrandioSO, Admira Fusion, Filtek Z550, Dynamic Plus). The gloss of the tested material was measured with a glossmeter before and after chemical degradation in different acidic beverages. Statistical analysis was performed using a t-test for dependent samples, ANOVA, and a post hoc test. For comparison between groups, a level of significance was set at 0.05. Initial gloss values ranged from 51 to 93 at baseline to 32 to 81 after chemical degradation. The highest values were obtained for Dynamic Plus (93.5 GU) and GrandioSO (77.8 GU), followed by Admira Fusion (82 GU) and Filtek Z550 (70.5 GU). Evetric showed the lowest initial gloss values. After acidic exposures, the gloss measurements revealed different patterns of surface degradation. The results showed that the gloss of the samples decreased with time regardless of the treatment. The interaction between chemical-erosive beverages and the composite could lead to a decrease in the surface gloss of the composite restoration. The nanohybrid composite showed less gloss changes under acidic conditions, suggesting that it is more suitable for anterior restorations.

Fusion of Unerupted Mesiodens with a Regular Maxillary Central Incisor: a Diagnostic and Therapeutic Challenge.

The mesiodens is the most frequent type of supernumerary tooth which can appear in the maxillary midline area. The etiology of mesiodentes is not fully understood. This report shows a case of incomplete fusion of an unerupted mesiodens with a permanent maxillary central incisor, aligned in the dental arch. Intraoral and radiographic examinations indicated fusion of the crown and cervical part of the root of the supernumerary tooth with the permanent incisor. The clinical situation was further complicated by the presence of another supernumerary tooth located palatally. The treatment approach has included two phase surgical therapy to extract the supernumerary teeth. Early diagnosis and appropriate surgical treatment of mesiodentes are important to decrease the risk of clinical complications. Pre-operative 3D imaging is strongly advisable since it allows accurate data to be obtained, and reduces the extent of surgery and the possibility of procedural complications. In most cases, a multidisciplinary collaboration is necessary for precise diagnosis and predictable treatment outcome.

Assessment of Cytotoxic and Genotoxic Effect of Fissure Sealants in Buccal Epithelial Cells.

AIM: The main purpose of this study was to assess the genotoxic and cytotoxic effect of fissure sealants on buccal epithelial cells. MATERIAL AND METHODS: The study was conducted on 45 patients (27 girls and 18 boys), seven to 16 years of age (age mean 12.09 ± 2.20). Buccal swabs were collected before (T0), seven (T1), 30 (T2) and 90 days (T3) consequently after fissure sealant placement (Helioseal F®, Equia Fil®, Constic®). Patients or legal guardians filled in the questionnaire regarding the demographic data (age, gender), dietary habits, health status, medication usage, and recent X-ray exposure. DNA damage was analyzed using the micronucleus test. RESULTS: Statistically significant difference in the number of buccal cells with condensed chromatin was found between T0 (time before fissure sealant placement) and T3 (90 days after fissure sealant placement) period for Helioseal F® (P = 0.025). For the other two analyzed materials, no difference was observed during the tested period. There was no difference between materials in the same sampling time. CONCLUSION: Apart from an increase in cells with condensed chromatin 90 days after the placement of Helioseal F®, no other nuclear abnormalities were observed for tested fissure sealants. Although these sealants have now largely been used, it is of high importance that their biocompatibility is checked continuously, especially in in vivo clinical studies.

Acceptance of Orthodontic Therapy according to the Aesthetic Component of the Index of Orthodontic Treatment Need among Schoolchildren - a Cross-Sectional Study.

OBJECTIVE: Orthodontic anomalies with impaired facial aesthetics and disturbed oral functions have a major effect on emotional and social development. It is necessary to determine the degree of acceptance of treatment. This study includes an evaluation of the Index of Orthodontic Treatment Need (IOTN) according to the Aesthetic Component (AC) of dental health in schoolchildren. METHODS: The research included 300 schoolchildren (150 girls, 150 boys) with an age range from 12 to 15 years. An evaluation of the need for orthodontic treatment according to the AC consisted of a ten-grade scale illustrated with a sequence of ten intraoral photographs showing different degrees of acceptability of dental appearance. Results were expressed as absolute and relative frequencies. The Chi-square test (in the absence of the expected frequencies of Fisher's Exact test) was used for testing the significance of differences. Cohen's kappa statistic measure was used for measuring the agreement between the children and dentists. RESULTS: There is a significant substantial agreement between children and dentists in assessing the need for orthodontic treatment. Differences in assessment of the degree of orthodontic anomalies by the doctor of dental medicine with respect to boys and girls, are negligible, and statistical analysis did not show any significant difference. Analysis of the need for orthodontic treatment with respect to the age of the children showed a significant difference. CONCLUSION: The need for orthodontic treatment is more pronounced in older children, and there is no difference between boys and girl.

Comparison of shear bond strengths of different types of denture teeth to different denture base resins.

PURPOSE: To determine the shear bond strengths of different denture base resins to different types of prefabricated teeth (acrylic, nanohybrid composite, and cross-linked) and denture teeth produced by computer-aided design/computer-aided manufacturing (CAD/CAM) technology. MATERIALS AND METHODS: Prefabricated teeth and CAD/CAM (milled) denture teeth were divided into 10 groups and bonded to different denture base materials. Groups 1-3 comprised of different types of prefabricated teeth and cold-polymerized denture base resin; groups 4-6 comprised of different types of prefabricated teeth and heat-polymerized denture base resin; groups 7-9 comprised of different types of prefabricated teeth and CAD/CAM (milled) denture base resin; and group 10 comprised of milled denture teeth produced by CAD/CAM technology and CAD/CAM (milled) denture base resin. A universal testing machine was used to evaluate the shear bond strength for all specimens. One-way ANOVA and Tukey post-hoc test were used for analyzing the data (α=.05). RESULTS: The shear bond strengths of different groups ranged from 3.37 ± 2.14 MPa to 18.10 ± 2.68 MPa. Statistical analysis showed significant differences among the tested groups (P<.0001). Among different polymerization methods, the lowest values were determined in cold-polymerized resin.There was no significant difference between the shear bond strength values of heat-polymerized and CAD/CAM (milled) denture base resins. CONCLUSION: Different combinations of materials for removable denture base and denture teeth can affect their bond strength. Cold-polymerized resin should be avoided for attaching prefabricated teeth to a denture base. CAD/CAM (milled) and heat-polymerized denture base resins bonded to different types of prefabricated teeth show similar shear bond strength values.

An In-Vitro Analysis of Microleakage of Self-Adhesive Fissure Sealant vs. Conventional and GIC Fissure Sealants.

BACKGROUND: The microleakage of a self-adhesive composite, a glass ionomer fissure sealant and a conventional resin-based fissure sealant were compared. MATERIALS AND METHODS: Fifty intact human molars with well-delineated pits and fissures were used and divided into 5 groups (n = 10). Group 1 specimens were etched (37% phosphoric acid) and sealed with conventional resin-based sealant (Helioseal F, Ivoclar Vivadent). Both Group 2 and 3 specimens were sealed with self-adhesive composite (Constic, DMG), but in Group 3, specimens were also etched (37% phosphoric acid). In Groups 4 and 5, specimens were sealed with a GIC sealant (Equia Fill, GC Company), but Group 5 was also exposed to thermo-light curing (TLC) with a LED polymerization unit (60 s). Subsequently, specimens were thermocycled (1800 cycles, dwelling time of 10 s), immersed in 50% silver nitrate solution (45 min), placed in a photo-developing solution (Kodak) under a lamp (120 W, 6 h), and cut into 3⁻4 slices. Marginal leakage (dye penetration depth) was evaluated under a light microscope and the worst score of each specimen was recorded (0⁻3). RESULTS: Constic showed the lowest microleakage (Constic: 80% scored 0 or 1), followed by Helioseal (30% scored 0 or 1) (p = 0.037). Microleakage in groups sealed with Constic (with and without etching) were not different (p = 0.473). The quality of seal deteriorated after etching when Constic was used. However, TLC improved the seal when GIC sealant was used (p = 0.016) and also in comparison to Helioseal (p = 0.004). The TLC GIC sealant (Equia Fill, 90% scored 0 or 1) performed well, similar to self-adhesive composite (Constic, 80% scored 0 or 1) (p = 0.206). CONCLUSION: The present findings suggest that the self-adhesive sealant and the GIC sealant that were exposed to TLC had comparable sealing ability and superior sealing characteristics compared to the conventional resin-based sealant. A long-term clinical trial is needed to assess the intra-oral performance.

In vivo assessment of genotoxicity in buccal cells of children undergoing tooth restoration.

OBJECTIVES: Whereas dental materials came in direct or close contact with oral tissue, it is a great concern about the biocompatibility of those materials. This study was performed to evaluate possible DNA damage to buccal cells exposed to dental materials. METHODS: This prospective, longitudinal clinical study was conducted over a three months period. Class II restorations were placed in 60 young patients with no previous filling using one of three tested dental materials (two glass ionomers; Ketac Molar and Ionofil Molar and one compomer material; Twinky Star). DNA damage was analysed by micronucleus assays, in buccal exfoliated epithelial cells. RESULTS: In patients treated with Ketac Molar, a significant frequency of micronuclei (p = 0.027) and binucleated cells in samples taken 30 days following restoration (p = 0.029) was confirmed. In patients treated with Twinky Star, a statistically significant increase in the number of binucleated cells in samples taken after 7 and 30 days following restoration (p = 0.001 and p < 0.001, respectively) was observed. In all samples collected 90 days after treatment, there was no statistical difference in the number of any cell changes. CONCLUSION: In this study long-term biocompatibility of tested materials was confirmed. Glass ionomers and compomers are widely used materials in paediatric dentistry, and this study has proved their safety for usage in children.

Influence of Toothpaste pH on Its Capacity to Prevent Enamel Demineralization.

AIM: This study evaluated in vitro the remineralization capacity of commercial toothpastes with different fluoride (F) concentrations and their effectiveness when they are acidified. MATERIALS AND METHODS: One hundred and twelve caries-free teeth were used to prepare enamel specimens, and the specimens were divided into 16 groups (n = 7). Baseline surface Vickers microhardness was measured for all the specimens and all the tested groups were subjected to the pH-cycling regime involved five demineralization challenges each day for 10 days, and surface Vickers microhardness was then measured. Once daily, specimens were exposed for 30 min after last demineralization challenge of the day to the slurry of each toothpaste containing 1450 ppm F, 1000 ppm F, 450 ppm F, and 0 ppm F. The slurry was in original pH or acidulated on 6.5, 6.0, or 5.5 pH. The difference among tested group was assessed by analysis of variance and Newman-Keuls test (P < 0.05). RESULTS: The highest increase in microhardness was detected after treatment with toothpaste containing 1450 ppm fluoride (percentage of increase in microhardness was 6.20%), and the biggest loss was detected after treatment with toothpaste containing no fluoride (percentage of decrease was 6.82%), but there was no significant difference between tested groups. CONCLUSIONS: The highest increase in microhardness was detected after treatment with toothpaste containing more fluorides (1450 ppm F) regardless of the acidity.

Surface Roughness of Glass Ionomer Cements after Application of Different Polishing Techniques.

Glass Ionomer Cements (GIC) have been widely used in clinical practice since they have a wide range of positive characteristics: chemical bonding to the tooth surface, fluoride release, a heat-expansion coefficient similar to the tooth, do not require an absolutely dry working area, less volumetric contraction, good color stability. Physical properties can be improved by using external energy such as ultrasound and radiant heat (thermo-curing), which also accelerates chemical curing. Objectives: The aim of this study was to determine the most effective polishing technique and to compare the surface roughness of two Glass Ionomer Cements after treatment with heat (thermo-curing), and without heat treatment during the setting process. Materials and methods: Two polishing systems (Tungsten carbide burs and Sof-Lex discs) were used on two types of GIC (Equia Fil and Ketac Molar Universal). Bluephase 16i LED (Vivadent, Schaan Liechtenstein) light was used for the specimens treated with heat (thermo-curing). Samples without heat treatment are left for 10 minutes to chemically cure. Surface profilometar was used for measuring the mean surface roughness value (Ra). Results: Group with Mylar strip (control group) of each material showed the lowest (Ra) value. The Equia Fil material samples treated with heat (thermo-curing) achieved lower surface roughness values (Ra), and showed lower surface roughness values (Ra) after polishing with a Sof-Lex discs (p<0.05). The results for Ketac Molar Universal samples showed no statistically significant difference (p>0.05) between polishing with Sof-Lex discs and Tungsten carbide burs. Conclusion: Based on the obtained results, it can be concluded that the smoothest surface roughness is achieved by the Mylar strip. Some types of Glass Ionomer Cements can obtain better surface polishing with heat treatment (thermo-curing).

The prevalence of orthodontic treatment needs of school children in northern Herzegovina.

OBJECTIVE: The study was conducted to evaluate the Index of Orthodontic Treatment Need based on the Dental Health Component (DHC). MATERIALS AND METHODS: 300 students aged 12-15 years were included in this study. The examinations were performed in two elementary schools in the municipality of Prozor-Rama, using standard dental instruments. Children were ranked into five grades according to the DHC. RESULTS: Only 12% of children were found not to have a need for orthodontic treatment. Of the others, 45.33% had a great, and 10% a very great need for orthodontic treatment. The rest of the children were found to have a need for minor or moderate orthodontic treatment. Slightly more girls than boys had a great or a very great need for treatment, although the difference by gender was not statistically significant. Analysis of the level of need by age of children showed no significant difference; children with a great need of orthodontic treatment prevailed in all age groups. About 85% of children with a great and a very great need for orthodontic treatment would agree to orthodontic treatment, while the rate of non-acceptance was about 5%. CONCLUSION: The high rate of need for orthodontic treatment in the examined students is explained by the lack of programs for this type of health care, the insufficient number of qualified orthodontic specialists, and the very low percentage of allocations from the state budget for oral health.

Thermo-cured glass ionomer cements in restorative dentistry.

Numerous positive properties of glass ionomer cements including biocompatibility, bioactivity, releasing of fluoride and good adhesion to hard dental tissue even under wet conditions and easy of handling are reasons for their wide use in paediatric and restorative dentistry. Their biggest drawbacks are the weaker mechanical properties. An important step forward in improving GIC's features is thermo-curing with the dental polymerization unit during setting of the material. Due to their slow setting characteristics the GIC is vulnerable to early exposure to moisture. After thermo curing, cements retain all the benefits of GIC with developed better mechanical properties, improved marginal adaptation, increased microhardness and shear bond strength. Adding external energy through thermocuring or ultrasound during the setting of conventional GIC is crucial to achieve faster and better initial mechanical properties. Further clinical studies are needed to confirm these findings.

Effect of different thermo-light polymerization on flexural strength of two glass ionomer cements and a glass carbomer cement.

STATEMENT OF PROBLEM: Whether polymerization lights can be used for heating glass ionomer cements (GICs) or glass carbomer (GCP) to improve their mechanical properties is not well established. PURPOSE: The purpose of this in vitro study was to assess the effect of thermo-light polymerization on the flexural strength (FS) of 2 GICs (Fuji IX GP Fast, Ketac Molar) and a GCP. MATERIAL AND METHODS: Specimens (n=10) were prepared in stainless steel molds (2×2×25 mm), compressed, exposed to 3 polymerization lights (500, 1000, 1200 mW/cm2) for 2 cycles of 40 seconds on each side, and stored in petroleum jelly (37°C, 24 hours). RESULTS: Significant FS differences were detected among groups after different thermo-light polymerization regimens (F=50.926, df=11, P<.001). GCP showed the highest mean FS (∼5 times, P<.001) after thermo-light polymerization with power outputs of 1000 (127.1 ±25.8 MPa) and 1200 mW/cm2 (117.4 ±18.5 MPa), with no significance difference between them (P=.98), compared with 500 mW/cm2 (24.1 ±1.7 MPa). For Ketac Molar, compared with autopolymerization setting (15.5 ±3.1 MPa), a significant increase in mean FS (∼2.5 times) was only observed in specimens treated with 1200 mW/cm2 polymerization light (P=.03). For Fuji IX GP Fast, only the light with 1000 mW/cm2 output significantly increased the FS (98.9 ±23.4 MPa, P<.001) compared with the autopolymerization setting (34.9 ±6.4 MPa). CONCLUSIONS: Thermo-light polymerization accelerated the development of FS in the tested GICs, potentially protecting against saliva contamination during the first 3 to 4 minutes after mixing GIC. Thermo-light polymerization of the glass carbomer with power outputs of 1000 and 1200 mW/cm2 also substantially increased FS. The clinical advantages of the findings should be validated by in vivo studies.

Influence of Thermo-Light Curing with Dental Light-Curing Units on the Microhardness of Glass-Ionomer Cements.

The purpose of this study was to verify for various glass-ionomer cement (GIC) products whether the application of thermo-light curing on the initial curing material produces an increase in microhardness, and to determine whether this hardness varies depending on the depths of the GIC samples. The efficacy of various polymerization units on this additional hardening was also examined. The GIC samples were thermo-light cured for 60 seconds with three polymerization units. The Vickers microhardness was measured at three different depths: 2 mm, 3 mm, and 4 mm. Analysis of variance and Newman-Keuls test showed statistically significant differences among tested samples for all three GIC groups (P < .001). The results of linear regression analysis showed a statistically significant relationship between the hardness of the material and the temperature for samples with depths of 2 mm (R = 0.78; P = .0028) and 3 mm (R = 0.59; P = .045). The findings of this study indicate that thermo-light curing of GIC with different polymerization units for 60 seconds during setting reaction increases the microhardness of the GICs at all depths tested and may increase resistance to mastication forces, which can be validated in future clinical studies.

The effect of petroleum jelly, light-cured varnish and different storage media on the flexural strength of glass ionomer dental cements.

This study determined the influence of coating with either petroleum jelly or light-cured varnish and storage medium on the flexural strength of glass-ionomer cements (GIC). The flexural strength of two glass-ionomer cements (Fuji Equia Fil and Ketac Molar Aplicap) was measured. Specimens (2 × 2 × 25 mm) were prepared in three groups: uncoated, coated with petroleum jelly, or coated with light-cured varnish (EquiaCoat) cured for 20 s using a cure lamp (Bluephase G2, Ivoclar Vivadent, Schaan, Liechtenstein). Specimens were stored for 1 week at 37 °C in water, artificial saliva or 20 mmol dm-3 lactic acid, then flexural strength was determined in 3-pont bend. Data were analyzed by ANOVA and Tukey HSD post hoc test (p < 0.05). In addition, the mold was filled with water and the temperature change caused by the cure lamp was measured with a thermocouple. For both materials, storage in water gave the lowest flexural strength. It was slightly higher in either saliva or lactic acid, and was improved by coating in petroleum jelly. Specimens coated with light-cured varnish, that also involved heating with a cure lamp, gave the highest flexural strength. The heating effect of the lamp was demonstrated by the temperature rise in the water in the mold after light exposure from 21.9 (± 1.0) °C to 26.8 (± 1.0) °C. hence, sealing of GIC from aqueous media improves flexural strength. The cure lamp emitted heat, which may enhance the flexural strength of specimens coated with light-cured varnish.

In-vitro Study on Temperature Changes in the Pulp Chamber Due to Thermo-Cure Glass Ionomer Cements.

The application of the Glass Ionomer Cements in clinical dentistry is recommended due to properties such as fluoride release, chemical adhesion to tooth, negligible setting shrinkage, and coefficient of thermal expansion close to tooth, low creep, and good color stability. However, the cement is vulnerable to early exposure to moisture due to slow setting characteristics. The uses of external energy such as ultrasound and radiant heat (Thermo-curing) have been reported to provide acceleration of the setting chemistry and enhance physical properties. Aim: The aim of this in vitro study was to analyze temperature changes in the pulpal chamber when using radiant heat to accelerate the setting of GICs. Material and Methods:The encapsulated GIC Equia Forte was used for this study. The temperature changes in the pulp were measured using thermocouple in the cavities which were 2,6 and 4,7mm deep with and without filling. Results:The results showed that a temperature rise (ΔT) in the pulp chamber was 3,7°C. ΔT for the 2.6mm and 4.7mm deep cavity and without placing any restoration the temperature was 4,2°C and 2,6°C respectively. After the restoration has been placed, the ΔT range in the pulp chamber was lower ranging from 1.9°C to 2.4°C. Conclusion: It could be concluded that Thermo-curing of the GIC during the setting is safe for the pulp and can be recommended in clinical practice.

Heat transfer properties and thermal cure of glass-ionomer dental cements.

Under clinical conditions, conventional glass-ionomer dental cements can be cured by application of heat from dental cure lamps, which causes acceleration in the setting. In order for this to be successful, such heat must be able to spread sufficiently through the cement to enhance cure, but not transmit heat so effectively that the underlying dental pulp of the tooth is damaged. The current study was aimed at measuring heat transfer properties of modern restorative glass-ionomers to determine the extent to which they meet these twin requirements. Three commercial glass ionomer cements (Ionofil Molar, Ketac Molar and Equia™ Fill) were used in association with three different light emitting diode cure lamps designed for clinical use. In addition, for each cement, one set of specimens was allowed to cure without application of a lamp. Temperature changes were measured at three different depths (2, 3 and 4 mm) after cure times of 20, 40 and 60 s. The difference among the tested groups was evaluated by ANOVA (P < 0.05) and post hoc Newman-Keuls test. All brands of glass-ionomer showed a small inherent setting exotherm in the absence of heat irradiation, but much greater temperature increases when exposed to the cure lamp. However, temperature rises did not exceed 12.9 °C. Application of the cure lamp led to the establishment of a temperature gradient throughout each specimen. Differences were typically significant (P < 0.05) and did not reflect the nominal power of the lamps, because those lamps have variable cooling systems, and are designed to optimize light output, not heating effect. Because the thermal conductivity of glass-ionomers is low, temperature rises at 4 mm depths were much lower than at 2 mm. At no time did the temperature rise sufficiently to cause concern about potential damage to the pulp.

Influence of Dentifrices pH on Enamel Microhardness In Vitro.

Purpose was to evaluate the effect of toothpastes pH on enamel remineralization. Six fluoride toothpaste and one without fluoride were applied to the enamel slabs. Twenty eight enamel slabs were divided into seven groups and subjected to a daily cycling regimen with brushing treatments, demineralization and remineralization in artificial saliva. The surface microhardness (SMH) was calculated from the mean values obtained from six indentations (Vickers hardness number (VHN)) on the enamel surface at baseline and after 12 days. pH of the dentifrices was determined in a slurry with deionized water (1:3). Changes of the enamel surface microhardness at baseline and after remineralization stage were measured and analyzed using the Student t-test and one-way ANOVA. All groups treated with fluorides showed higher SMH values compared to control group. Toothpastes with lower pH (Pronamel, Sensodyne F, Sensodyne Rapid) were statistically superior to other fluoride dentifrices and control group after 12 days pH-cycling regimen (p < 0.001). Obtained results showed that slightly acidified fluoridated toothpastes may have a positive influence on enamel remineralization process.

Prevalence of periodontal diseases in North Herzegovina.

AIM: To investigate effects of smoking on periodontal tissue and the occurrence of periodontal disease in the population of North Herzegovina. METHODS: The study included 800 persons of 20-49 years of age (400 smokers and 400 non-smokers), inhabitants of Prozor-Rama Municipality, Bosnia and Herzegovina. Periodontal condition assessment was made by the Community Periodontal Index of Treatment Needs index (CPITN) at representative teeth: 16, 17, 21, 26, 27, 36, 37, 31, 46, and 47.Statistically significant difference between non-smokers and smokers was tested by χ2 test with the level of significance set at p=0.05. RESULTS: The prevalence of healthy periodontal tissues was lower in smokers than in non-smokers, 25 (6.3%)and 36 (9%), respectively. The prevalence of gingival bleeding, calculus, shallow and deep periodontal pockets was higher in smokers than in non-smokers, although it was not significant. There was a risk between occurrence of deep periodontal pockets and smoking (RR=2). A total of 64 (8%)participants neededonly instructions on proper oral hygiene, 654 (81.8%) prophylaxis and initial treatment,while 21 (2.6%) needed complex periodontal treatment. CONCLUSION: Obtained results indicate a high need of preventive measures and the improvement of oral health in the population of North Herzegovina.

Taekwondo coaches knowledge about prevention and management of dental trauma.

The aim of this study was to assess level of knowledge about prevention and dental trauma management among taekwondo coaches in Croatia. The questionnaire submitted to the taekwondo coaches contained 16 items about dental trauma prevention and management. The questionnaires were filled in by 131 taekwondo coaches; 28 females and 103 males. Descriptive statistics was used to describe and analyze the obtained data. The coaches were familiar with dental injuries in high percentage: 41 (31.3%) have observed dental injury and 36 (27.5%) have experienced a dental injury themselves. Eight of them had tooth avulsion, fourteen crown fracture, and eight had tooth luxation. About half of all interviewed coaches 68 (52.7%) were aware of the possibility of replanting avulsed teeth. Twenty six (19.8%) were familiar with the tooth rescue kit. Only 99 out of 131 coaches (75.6%) have used a mouthguard. The obtained results show low knowledge about possibilities for prevention of dental trauma. Insufficient use of mouthguards in this contact sport requires more attention of dentists and coaches education about dental trauma prevention.