Effectiveness of cork and pine bark powders as biosorbents for potentially toxic elements present in aqueous solution.

Cork oak and pine bark, two of the most prolific byproducts of the European forestry sector, were assessed as biosorbents for eliminating potentially toxic elements (PTEs) from water-based solutions. Our research suggests that bioadsorption stands out as a viable and environmental eco-friendly technology, presenting a sustainable method for the extraction of PTEs from polluted water sources. This study aimed to evaluate and compare the efficiency of cork powder and pine bark powder as biosorbents. Specifically, the adsorption of Fe, Cu, Zn, Cd, Ni, Pb and Sn at equilibrium were studied through batch experiments by varying PTEs concentrations, pH, and ionic strength. Results from adsorption-desorption experiments demonstrate the remarkable capacity of both materials to retain the studied PTE. Cork powder and pine bark powder exhibited the maximum retention capacity for Fe and Cd, while they performed poorly for Pb and Sn, respectively. Nevertheless, pine bark showed a slightly lower retention capacity than cork. Increasing the pH resulted in cork showing the highest adsorption for Zn and the lowest for Sn, while for pine bark, Cd was the most adsorbed, and Sn was the least adsorbed, respectively. The highest adsorption of both materials occurred at pH 3.5-5, depending on the PTE tested. The ionic strength also influenced the adsorption of the various PTEs for both materials, with decreased adsorption as ionic strength increased. The findings suggest that both materials could be effective for capturing and eliminating the examined PTEs, albeit with different efficiencies. Remarkably, pine bark demonstrated superior adsorption capabilities, which were observed to vary based on the specific element and the experimental conditions. These findings contribute to elucidating the bio-adsorption potential of these natural materials, specifically their suitability in mitigating PTEs pollution, and favoring the recycling and revalorization of byproducts that might otherwise be considered residue.

Use of Three Different Nanoparticles to Reduce Cd Availability in Soils: Effects on Germination and Early Growth of Sinapis alba L.

Globally, cadmium (Cd) is one of the metals that causes the most significant problems of contamination in agricultural soils and toxicity in living organisms. In this study, the ability of three different nanoparticles (dose 3% w/w) (hydroxyapatite (HANPs), maghemite (MNPs), or zero-valent iron (FeNPs)) to decrease the availability of Cd in artificially contaminated agricultural soil was investigated. The effect of Cd and nanoparticles on germination and early growth of Sinapis alba L. was also assessed by tolerance/toxicity bioassays. The available Cd contents in the contaminated soil decreased after treatment with the nanoparticles (available Cd decreased with HANPs: >96.9%, MNPs: >91.9%, FeNPs: >94%), indicating that these nanoparticles are highly efficient for the fixation of available Cd. The toxicity/tolerance bioassays showed different behavior for each nanoparticle. The HANPs negatively affected germination (G(%): 20% worsening compared to control soil), early root growth (Gindex: -27.7% compared to control soil), and aerial parts (Apindex: -12%) of S. alba, but showed positive effects compared to Cd-contaminated soils (Gindex: +8-11%; Apindex: +26-47%). MNP treatment in Cd-contaminated soils had a positive effect on germination (G(%): 6-10% improvement) and early growth of roots (Gindex: +16%) and aerial parts (Apindex: +16-19%). The FeNPs had a positive influence on germination (G(%): +10%) and growth of aerial parts (Apindex: +12-16%) but not on early growth of roots (Gindex: 0%). These nanoparticles can be used to reduce highly available Cd contents in contaminated soils, but MNPs and FeNPs showed the most favorable effects on the early growth and germination of S. alba.

Do heavy metals affect bacterial communities more in small repeated applications or in a single large application?

Heavy metals from anthropogenic sources accumulate slowly but steadily, leading to high metal concentration levels in soil. However, the effect of each heavy metal on soil bacterial communities is usually assessed in laboratories by a single application of individually spiked metals. We evaluated the differences between single individual application and repeated individual applications of Cr, Cu, Ni, Pb, and Zn on bacterial communities, through pollution-induced community tolerance (PICT), using bacterial growth as the endpoint (3H-leucine incorporation method). We found that PICT development was higher when soil was spiked in individual single application than individual repeated applications for Cu, Ni and Zn. In contrast, bacterial communities did not show different tolerance between singly or repeatedly when soil was spiked with Cr. In the case of Pb any increase of bacterial community tolerance to this metal was found despite high doses applied (up to 2000 mg kg-1). These results are relevant for the interpretation of the effects of heavy metals on soil microbes in order to avoid laboratory overestimations of the real effects of heavy metals on soil microbes.

Influence of soil properties on the development of bacterial community tolerance to Cu, Ni, Pb and Zn.

Pollution-Induced Community Tolerance (PICT) is a helpful and sensitive methodology to evaluate the effect of metal pollution in soils using microorganisms as indicators. PICT was used to determine the increase of bacterial community tolerance to Cu, Ni, Pb and Zn (Δlog IC50), and to assess the influence of soil properties on the development of bacterial community tolerance to Cu, Ni, Pb, and Zn. Soil samples showed a wide range of properties, such as pH (3.96-7.47), texture (13.8-31.7% clay) or organic matter (9.7-30.7%). Bacterial growth measured by the [3H]-leucine incorporation method was used as the PICT endpoint. Bacterial communities generally developed tolerance in response to Cu, Ni and Zn additions to soils. However, bacterial communities showed no tolerance to Pb, probably due to high Pb sorption in studied soils. Soil properties influenced the development of bacterial community tolerance to Cu, Ni and Zn. Effective cation exchange and a soil sorption parameter (Freundlich's linearity index) were the selected variables to estimate Δlog IC50 to Cu (R2 = 0.65). Clay content and Ni-soluble are the main factors to estimate Δlog IC50 to Ni (R2 = 0.63). Organic matter content and a sorption parameter (maximum sorption capacity of the soil from Langmuir equation) are the soil properties to estimate Δlog IC50 to Zn (R2 = 0.45). Most of the variables exerted their effect in soil, i.e. PICT selection phase. However, clay content affected bacterial community tolerance determination (PICT detection phase), leading to overestimated measurements of bacterial community tolerance.