An apta-aggregation based machine learning assay for rapid quantification of lysozyme through texture parameters.

A novel assay technique that involves quantification of lysozyme (Lys) through machine learning is put forward here. This article reports the tendency of the well- documented Ellington group anti-Lys aptamer, to produce aggregates when exposed to Lys. This property of apta-aggregation has been exploited here to develop an assay that quantifies the Lys using texture and area parameters from a photograph of the elliptical aggregate mass through machine learning. Two assay sets were made for the experimental procedure: one with high Lys concentration between 25-100 mM and another with low concentration between 1-20 mM. The high concentration set had a sample volume of 10 µl while the low concentration set had a higher sample volume of 100 µl, in order to obtain the statistical texture values reliably from the aggregate mass. The platform exhibited an experimental limit of detection of 1 mM and a response time of less than 10 seconds. Further, two potential operating modes for the aptamer were hypothesized for this aggregation property and the more accurate mode among the two was ascertained through bioinformatics studies.

Sorting the main bottlenecks to use paper-based microbial fuel cells as convenient and practical analytical devices for environmental toxicity testing.

Three of the primary bottlenecks, which should be consider for practical, point-of-need use of microbial fuel cell (MFC) analytical devices were surpassed in this work: i) the use of a diffusive barrier, hence, an electrogenic biofilm; ii) longer enrichment/stabilization times to produce a biofilm, made in a laboratory environment, over the electrode; and iii) difficulty comparing results obtained from MFCs based on electrogenic biofilms with standardized bioassays, a setback to be adopted as a new method. Here we show an easy way to determine water toxicity employing planktonic bacteria as biorecognition agents. The paper-based MFC contain an electron carrier (or mediator) to facilitate charge transfer from bacteria to the anode. In this way, there is no need to use biofilms. As far as we know this is the first paper-based MFC containing P. putida KT2440, a well characterized non-pathogenic bacteria previously used in standardized water toxicity bioassays. Results were obtained in 80 min and an effective concentration 50 of 9.02 mg L-1, calculated for Zn2+ (a reference toxic agent), was successfully compared with previously published and ISO standardized bioassays, showing a promising future for this technology. The practical design and cost (less than one U.S. dollar) of the paper-based MFC toxicity test presented will open new market possibilities for rapid and easy-to-use MFC analytical devices.

Hydrogen production in two-chamber MEC using a low-cost and biodegradable poly(vinyl) alcohol/chitosan membrane.

Hydrogen production was evaluated in two-chamber microbial electrolysis cells (MEC), where the chambers of the cell were separated using a new economical and environmentally friendly membrane made of poly (vinyl) alcohol/chitosan (PVA/CS). The MEC performance was compared to that of Nafion. The obtained results indicated that the MEC performance for hydrogen production did not show significant differences between the PVA/CS and Nafion membranes. MEC with PVA/CS showed the hydrogen production rate and hydrogen yield of 1277 ± 46 mL H2Lcat-1d-1 and 974 ± 116 mL H2 gacetate-1, respectively. The PVA/CS membrane allowed acetate removal that was 7% higher than that of Nafion due to the lower pH gradient and a lower voltage drop that increased the ion transfer across the membrane.

Characterization of a new composite membrane for point of need paper-based micro-scale microbial fuel cell analytical devices.

Microbial fuel cells (MFCs) can evolve in a viable technology if environmentally sound materials are developed and became available at low cost for these devices. This is especially important not only for the designing of large wastewater treatment systems, but also for the fabrication of low-cost, single-use devices. In this work we synthesized membranes by a simple procedure involving easily-biodegradable and economic materials such as poly (vinyl alcohol) (PVA), chitosan (CS) and the composite PVA:CS. Membranes were chemical and physically characterized and compared to Nafion®. Performance was studied using the membrane as separator in a typical H-Type MFCs showing that PVA:CS membrane outperform Nafion® 4 times (power production) while being 75 times more economic. We found that performance in MFC depends over interactions among several membrane characteristics such as oxygen permeability and ion conductivity. Moreover, we design a paper-based micro-scale MFC, which was used as a toxicity assay using 16 µL samples containing formaldehyde as a model toxicant. The PVA:CS membrane presented here can offer low environmental impact and become a very interesting option for point of need single-use analytical devices, especially in low-income countries where burning is used as disposal method, and toxic fluoride fumes (from Nafion®) can be released to the environment.