Effect of Bacterial Cellulose Plasma Treatment on the Biological Activity of Ag Nanoparticles Deposited Using Magnetron Deposition.

New functional medical materials with antibacterial activity based on biocompatible bacterial cellulose (BC) and Ag nanoparticles (Ag NPs) were obtained. Bacterial cellulose films were prepared by stationary liquid-phase cultivation of the Gluconacetobacter hansenii strain GH-1/2008 in Hestrin-Schramm medium with glucose as a carbon source. To functionalize the surface and immobilize Ag NPs deposited by magnetron sputtering, BC films were treated with low-pressure oxygen-nitrogen plasma. The composition and structure of the nanomaterials were studied using transmission (TEM) and scanning (SEM) electron microscopy and X-ray photoelectron spectroscopy (XPS). Using electron microscopy, it was shown that on the surface of the fibrils that make up the network of bacterial cellulose, Ag particles are stabilized in the form of aggregates 5-35 nm in size. The XPS C 1s spectra show that after the deposition of Ag NPs, the relative intensities of the C-OH and O-C-O bonds are significantly reduced. This may indicate the destruction of BC oxypyran rings and the oxidation of alcohol groups. In the Ag 3d5/2 spectrum, two states at 368.4 and 369.7 eV with relative intensities of 0.86 and 0.14 are distinguished, which are assigned to Ag0 state and Ag acetate, respectively. Nanocomposites based on plasma-treated BC and Ag nanoparticles deposited by magnetron sputtering (BCP-Ag) exhibited antimicrobial activity against Aspergillus niger, S. aureus and Bacillus subtilis.

Liquid-crystalline ordering in bacterial cellulose produced by Gluconacetobaсter hansenii on glucose-containing media.

This research is dedicated to the studies of the microscale morphology of bacterial cellulose (BC) obtained by means of static cultivation of Gluconacetobacter hansenii GH-1/2008. We found that the microscale morphology depended on the BC production rate that was varied by using different glucose concentrations in the cultivation medium. It was revealed that at higher production rates, BC fibrils were aligned in a liquid-crystalline-like (LC-like) order. The observed helical alignment was always left-handed. The half-periods of the helix varied from 50 µm to 150 µm depending on the cultivation conditions. The mechanical and water absorption properties of the obtained BC pellicles were measured. The former correlated mainly with the density of the samples; the latter were the best for films with layered structure, where the BC had segregated into fleece sheets separated by gaps with low density of fibrils.

Green approach for fabrication of bacterial cellulose-chitosan composites in the solutions of carbonic acid under high pressure CO2.

The functionalization of the bacterial cellulose (BC) surface with a chitosan biopolymer to expand the areas of possible applications of the modified BC is an important scientific task. The creation of such composites in the carbonic acid solutions that were performed in this work has several advantages in terms of being biocompatible and eco-friendly. Quantitative analysis of chitosan content in the composite was conducted by tritium-labeled chitosan radioactivity detection method and this showed three times increased chitosan loading. Different physicochemical methods showed successful incorporation of chitosan into the BC matrix and interaction with it through hydrogen bonds. Microscopy results showed that the chitosan coating with a thickness of around 10 nm was formed in the bulk of BC, covering each microfibril. It was found that the inner specific surface area increased 1.5 times on deposition of chitosan from the solutions in carbonic acid.

Structural organization of bacterial cellulose: The origin of anisotropy and layered structures.

In this paper, we perform a systematic analysis of the structural organization of bacterial cellulose (BC). We report four types of organization of the BC mass, produced by Gluconacetobacter hansenii that occur depending on cultivation conditions. Two of those, particularly, plywood type one and layers of micro-sized tubes were observed and described for the first time. In spherical BC particles (pellets), we found the layered structure that had previously been reported for planar geometry only. We suggest a model explaining why layers form in BC films and attempt to reveal the impact of different factors on the BC microscale morphology. We assume that the main factor that has direct impact on the type of structure formed is the rate of BC mass accumulation.