Five or more gender- and size-diverse customizations of distal femur prostheses are needed to improve fit for Chinese knees.

PURPOSE: Mismatch between partial imported prostheses and Chinese anatomy affects the clinical outcome of the procedure. The purpose of this study was to measure the anatomical dimensions of Chinese distal femurs to provide guidance for the design of more compatible distal femoral prostheses. METHODS: A total of 406 healthy distal femurs were reconstructed and measured. Consistency of these measurements and differences in sides, gender, and populations were examined. Parameter correlations were analyzed, and pairs with strong correlations underwent linear regression analysis. The design of distal femoral prostheses was referenced from the results of K-means and hierarchical clustering analysis. RESULTS: Ten parameters were measured, including the trans-epicondylar axis, width of the distal femur (ML), anteroposterior diameter of the distal femur (AP), etc. The intra-class correlation coefficient ranged from 0.795 to 0.999 for intra-observer consistency, and from 0.796 to 0.998 for inter-observer consistency. Males exhibited significantly larger parameters than females, except for the posterior condylar angle (all P values < 0.05). Compared to other populations, substantial differences were observed for most parameters, such as ML, AP, width of lateral femoral condyle, etc. (all P values < 0.05). Clustering analysis suggested that distal femoral prostheses should include at least five sizes to adequately accommodate the sampled population. ML sizes for males were 68, 70, 83, 73, and 89 mm, and for females 64, 65, 71, 67, and 77 mm. AP sizes for males were 56, 60, 60, 64, and 64 mm, and for females 48, 52, 54, 57, and 58 mm. CONCLUSIONS: Chinese distal femur morphology, as analyzed using 3D techniques, varies significantly between genders and when compared with international data. For improved patient fit, the creation of five or more distal femur prostheses, diversified by gender and size and informed by the associated morphological parameters, is recommended. LEVEL OF EVIDENCE: IV.

Three-dimensional computed tomography mapping techniques in the morphometric analysis of AO/OTA 33A and 33C distal femoral fractures: a retrospective single-center study.

Purpose: Complex distal femoral fractures involve a challenging set of considerations that must be known to provide optimal management. This study aimed to determine the location and frequency of fracture lines and comminution zones in AO/OTA types 33A and 33C distal femoral fractures using three-dimensional computed tomography mapping. Methods: Seventy-four consecutive eligible patients were included. Fracture fragments for each patient were reconstructed, virtually reduced, and adjusted to match the distal femoral template. Then, all fracture lines and comminuted areas were extracted in transparent mode, and corresponding heat maps were constructed. Finally, these maps, along with the quantitative analysis findings of the counts and volumes of each fragment, were used to summarize the characteristics of the fractures. Results: Thirty-four females and 40 males [average age, 58 years (range, 18-92 years)] presented with a distal femoral fracture. There were 53 AO/OTA type 33A fractures, and 21 AO/OTA type 33C fractures. These two patterns differed significantly on fracture fragment count, comminuted zone fracture fragment count, and mean comminuted zone fracture fragment volume (p < 0.05). Most of the fracture line heat zones were in the femoral epiphysis, intercondylar notch of the femur, and patellofemoral joint. The comminuted area heat regions were mostly found on the lateral, anterior, and posterior femoral diaphysis, with less involvement on the medial side. Conclusion: Our findings may serve as a guide for the surgical approach selection of complex distal femur fractures, the placement strategy of the internal fixation, and the optimization of the osteotomy plan for biomechanical studies.

Transosseous-Equivalent/Suture Bridge Technique in Combination With Platelet-Rich Plasma Application Yield Optimal Clinical Outcomes in Arthroscopic Rotator Cuff Repair: A Bayesian Network Analysis of Randomized Controlled Trials.

PURPOSE: To assess the clinical evidence defining the optimal combination of arthroscopic suture technique and platelet-rich products (PRP), and application for arthroscopic rotator cuff repair (ARCR). METHODS: All level of evidence (LOE) I randomized controlled trials (RCT) focusing on arthroscopic suture technique and/or PRP application in ARCR were included. The exclusion criteria were LOE II or worse, studies with other interventions, studies reported none of the predetermined clinical outcomes; studies unable to extract any precise data; studies from the same patient group of included studies. A pair-wise meta-analysis and Bayesian network analysis were performed on each comparison. The intervention options were ranked by Bayesian network analysis. RESULTS: 27 studies comprising 1,947 individuals met the inclusion criteria. The application of transosseous equivalent/suture bridge repair (SB) with PRP (SB+PRP) significantly reduced retear rate (risk ratio [RR], 0.29; 95% confidence interval [CI], [0.15, 0.55].) and increased Constant-Murley score (mean difference, 1.90; 95% CI, [0.14, 3.74]), compared to SB repair. Single-row repair (SR) with PRP usage (SR+PRP) significantly reduced retear rate (RR, 0.27; 95% CI, [0.12, 0.55]) and pain visual analog scale (VAS) (mean difference: -0.84; 95% CI [-1.39, -0.46].), increased University of California, Los Angeles (UCLA) shoulder score (mean difference: 1.48; 95% CI [0.50, 2.58]) and Constant-Murley score (mean difference: 4.53; 95% CI [2.65, 6.38]), compared to SR repair. The ranking for outcomes demonstrated SB+PRP resulted in the best retear rate, UCLA shoulder score, with the second-best postoperative pain, Constant-Murley score, while SR+PRP resulted in the best postoperative pain, Constant-Murley score, with the second-best retear rate and UCLA score. CONCLUSION: Arthroscopic rotator cuff repair utilizing SB+PRP yields optimal retear rate and UCLA shoulder score, with the second-best postoperative pain and Constant-Murley shoulder outcome score, while SR+PRP yields the best in these two parameters. LEVEL OF EVIDENCE: Level I, Bayesian network analysis of level I RCT.

Identification of hub genes correlated with tumor-associated M1-like macrophage infiltration in soft tissue sarcomas.

Soft tissue sarcomas (STS) are a heterogeneous series of tumors that might result in severe disability and death. Tumor-associated M1-like macrophage infiltration plays a critical role in tumor development and progression. This study aimed at identifying the hub genes associated with M1-like macrophage infiltration in STS cells. First, the expression profiles from The Cancer Genome Atlas (TCGA) and Gene Expression Omnibus (GEO) databases were imported to calculate the level of M1-like macrophage infiltration by CIBERSORTx. Afterward, the Kaplan-Meier survival analysis was performed to evaluate the correlation between macrophage infiltration and prognosis. Then, weighted gene co-expression network analysis (WGCNA) and protein-protein interaction analysis of GEO data were applied to identify the key gene related to M1-like macrophage infiltration, followed by the functional analysis using TCGA cohort to validate downstream signaling associated with the gene. Finally, pan-cancer analysis was conducted to investigate the gene function in other types of tumors. We found LCK expression positively related to the M1-like macrophage infiltration level, and it positively regulated the expression level of genes regulated to macrophage polarization, and chemotaxis, including interferon-γ (INF-γ), interleukin-12 (IL12), tumor necrosis factor (TNF), PI3K, NF-κB, and CXCL9, 10, and 11. In summary, an 'LCK-INF-γ/IL-12-TNF/PI3K-NF-κB' axis might exist in STS cells that regulate M1-like macrophage infiltration.

Imperatorin induces autophagy and G0/G1 phase arrest via PTEN-PI3K-AKT-mTOR/p21 signaling pathway in human osteosarcoma cells in vitro and in vivo.

BACKGROUND: Osteosarcoma is the third most common cancer in adolescence and the first common primary malignant tumor of bone. The long-term prognosis of osteosarcoma still remains unsatisfactory in the past decades. Therefore, development of novel therapeutic agents which are effective to osteosarcoma and are safe to normal tissue simultaneously is quite essential and urgent. METHODS: Firstly, MTT assay, cell colony formation assay, cell migration and invasion assays were conducted to evaluate the inhibitory effects of imperatorin towards human osteosarcoma cells. RNA-sequence assay and bioinformatic analysis were then performed to filtrate and assume the potential imperatorin-induced cell death route and signaling pathway. Moreover, quantitative real-time PCR assay, western blot assay and rescue experiments were conducted to confirm the assumptions of bioinformatic analysis. Finally, a subcutaneous tumor-transplanted nude mouse model was established and applied to evaluate the internal effect of imperatorin on osteosarcoma by HE and immunohistochemistry staining. RESULTS: Imperatorin triggered time-dependent and dose-dependent inhibition of tumor growth mainly by inducing autophagy promotion and G0/G1 phase arrest in vitro and in vivo. Besides, imperatorin treatment elevated the expression level of PTEN and p21, down-regulated the phosphorylation of AKT and mTOR. In contrast, the inhibition of PTEN using Bpv (HOpic), a potential and selective inhibitor of PTEN, concurrently rescued imperatorin-induced autophagy promotion, cell cycle arrest and inactivation of PTEN-PI3K-AKT-mTOR/p21 pathway. CONCLUSIONS: This work firstly revealed that imperatorin induced autophagy and cell cycle arrest through PTEN-PI3K-AKT-mTOR/p21 signaling pathway by targeting and up-regulating PTEN in human osteosarcoma cells. Hence, imperatorin is a desirable candidate for clinical treatments of osteosarcoma.

The comparison of Nice knots and traditional methods as an auxiliary reduction-fixation technique in pre-contoured locking plate fixation for comminuted Robinson type 2B clavicle fracture: A retrospective study.

ABSTRACT: Open reduction and pre-contoured locking plate fixation is a popular treatment option for displaced midshaft clavicle fracture. Lag screw and cerclage are 2 main intraoperative techniques to reduce and fix fragments. However, both lag screw and metallic cerclage have disadvantages. The doubled-suture Nice knot has been reported in many areas of orthopedic surgery for its effectiveness. This study aims to compare the outcomes of comminuted mid-shaft clavicle fractures reduced by Nice knots vs traditional techniques (lag screw or/and metallic cerclage) when bridged with pre-contoured locking plates.We retrospectively reviewed 101 patients (65 females and 36 males) diagnosed with midshaft clavicle fractures with at least one wedge fragment reduced by either Nice knots or traditional methods and bridged with pre-contoured locking plates between December 2016 and April 2019. Operation time, functional outcomes, pain, patient satisfaction, fracture healing, and complications were assessed at a follow-up of 12 to 40 months.The mean age of all the patients was 50.8 years. There were 52 and 49 patients in the Nice knot group and traditional group respectively, and no differences between 2 groups were found in general patient characteristics, fracture type, follow up and injury-to-surgery duration. The Nice knot group had significant less operation time (P < .01) than the traditional group (mean and standard deviation [SD], 78.6 ±â€Š19.0 compared with 94.4 ±â€Š29.9 minutes, respectively). For healing time, functional score, pain, satisfaction and complications, there were no significant differences between groups, despite the Nice knot group had slightly better results.Both Nice knots and traditional methods treated for comminuted Robinson type 2B clavicle fractures were effective and safe. And the Nice knots seemed to be superior with significant less operation time.

Prevalence of vertebral endplate modic changes in degenerative lumbar scoliosis and its associated factors analysis.

STUDY DESIGN: A retrospective study of modic changes (MCs) in degenerative lumbar scoliosis (DLS). OBJECTIVE: To investigate the prevalence of vertebral endplate MCs in DLS and explore their associated factors. SUMMARY OF BACKGROUND DATA: MCs are common in spinal degenerative diseases. Presently, most of the researches have been focused on investigating the relationship between MCs and chronic low back pain. Little has been known on the distribution of MCs in DLS and the relationship between MCs and scoliosis. METHODS: The image data of 120 patients who had been diagnosed with DLS in our hospital from March 2005 to March, 2011 were retrospectively reviewed as the study group. The image data of 89 patients who had been diagnosed with degenerative lumbar diseases without scoliosis were selected as the control group. The prevalence, type, and distribution of MCs in 2 groups were observed and compared. Disc degeneration, Cobb angle, body weight, and smoking were recorded in the study group, and the relationship of MCs with these influential factors was analyzed. RESULTS: Of 1440 endplates from 120 patients in the study group, 247 (17.2%) from 71 (59.2%) patients were found to have MCs. Compared with the control group, of 1068 endplates from 89 patients, 49 (4.5%) endplates from 21 (23.6%) patients were found to have MCs. The prevalence of MCs was significantly higher in the study group than that in the control group (P < 0.01). The MCs in DLS usually had asymmetric distribution with more frequent occurrence on the concave side than on the convex side of major or compensatory curve and mainly occurred at L2-L3, L4-L5, and L5-S1, which were in accordance with the common levels of apex vertebrae. Intervertebral disc degeneration, lumbar scoliosis, overweight and heavy smoking are considered as risk factors to MCs. By multinomial logistic regression analysis on these factors, the regression function was obtained: logit Y = -0.82 + 1.27D + 0.55S + 1.77 D × S (Y for MCs, D for intervertebral disc degeneration, S for scoliosis Cobb's angle and D × S for interaction of D and S). CONCLUSION: The prevalence of MCs in patients with DLS was significantly higher than that of patients without DLS. Most of them were type 2 and usually located on the concave side of apex vertebrae. MCs were significantly associated with intervertebral disc degeneration and lumbar scoliosis.

[Analysis of factors of formation and development about degenerative lumbar scoliosis].

OBJECTIVES: To investigate the correlation between scoliosis angle and the asymmetric index of degenerative lumbar scoliosis, the degree of intervertebral disc degeneration, decreased bone density. METHODS: As a retrospectively study, a total of 96 patients with degenerative lumbar scoliosis were retrospectively enrolled from January 2002 to August 2010 as scoliosis group, meanwhile 96 patients with lumbar spinal stenosis matched in gender, age and body mass index (BMI) were selected as control group. All patients were studied with plain radiographs, MRI and dual energy X-ray absorptiometry at presentation. Radiographic measurements include Cobb angle, the height of the convex and concave side of the apical disc and the contiguous disc superiorly and inferiorly, the height of the convex and concave side of the apical and the contiguous vertebral body superiorly and inferiorly in scoliosis group, the height of L(2-3), L(3-4), L(4-5) discs and the height of L(2-4) vertebral body in control group. The average relative signal intensity of lumbar intervertebral disc and cerebrospinal fluid in T2WI sagittal image was measured in apex intervertebral disc and adjacent discs by Adobe Photoshop 6.0 in scoliosis group, which was measured in L(2-3), L(3-4), L(4-5) disc in control group. The bone density of lumbar, femoral neck, trochanter, and Ward's triangle regions were measured with dual-energy X-ray absorptiometry. RESULTS: The intervertebral disc height in convex side was greater than the height in the concave side [(40 ± 7) mm vs. (28 ± 7) mm, P < 0.01], the vertebral body height in convex side was greater than the height in the concave side [(76 ± 12) mm vs. (72 ± 10) mm, P = 0.016] in scoliosis group. There was significant statistically difference in the degenerative degree of intervertebral discs between two groups (P = 0.003). There was significant statistically difference of the average T-value and the rate of osteoporosis between two groups (P < 0.01). Multiple linear regression analysis showed that the asymmetric disc index, the degenerative degree of intervertebral disc and osteoporosis were the predominant correlative factors, which affected the development of degenerative lumbar scoliosis. CONCLUSIONS: Degenerative lumbar scoliosis is always accompanied by the height asymmetry of intervertebral discs and vertebral body from convex and concavity sides. There is positive correlation between the angle of scoliosis and the asymmetric disc index, the degeneration of intervertebral disc, and negative correlation between the angle of scoliosis and the bone density (T-value).

[Correlation between intervertebral disc-endplate degeneration and bony structural parameter in adult degenerative scoliosis and its significance].

OBJECTIVES: To analyze the correlation between intervertebral disc-endplate degeneration and bony construction parameter and to explore its roles in adult degenerative scoliosis. METHODS: The imaging data of 79 patients with adult degenerative scoliosis from March 2005 to March 2010 were retrospectively reviewed as the study group. The imaging data of 41 patients with adolescent idiopathic scoliosis were selected as the control group. The vertebral body and intervertebral height in both sides on frontal X-ray, and the facet joint orientation in both sides on CT scan were measured respectively. The average vertebral body height, average intervertebral disc height and average facet orientation were regarded as bony structural parameters. The quantitative grading methods were used in the intervertebral disc and endplate degeneration. The relationship of bony construction parameter and intervertebral disc-endplate degeneration, and the relationship of bony construction parameter and Cobb's angle of scoliosis were analyzed by comparing all bony construction parameters in both groups. RESULTS: Analyzed by paired-t test, the intervertebral height, vertebral body height and facet joint orientation between convex and concave sides of the study group were of significant difference (t = 3.411, 2.623 and 2.085, P < 0.05). The intervertebral height between convex and concave sides of the control group were of significant difference (t = 3.276, P < 0.01), while the vertebral body height and the facet joint orientation were of no statistical significance (t = 1.572 and 1.493, P > 0.05). By linear correlation and regression analysis, the asymmetric degree of bony construction parameter showed good correlation with the score of intervertebral disc-endplate degeneration (-1 < r < 1, P < 0.05), which was positively correlated with Cobb's angle of scoliosis (0 < r < 1, P < 0.05). Linear regression existed between asymmetric degree of bony construction parameter and Cobb's angle (F = 427.342, P < 0.01). The regression function was obtained: Cobb's angle = -8.904+8.136 × IAD + 3.274 × VAD-0.713 × FAD (IAD: intervertebral asymmetry degree, VAD: vertebral asymmetry degree, FAD: facet joint asymmetry degree). CONCLUSIONS: The asymmetric change of bony construction exists in adult degenerative scoliosis, which significantly correlated with intervertebral disc-endplate degeneration and Cobb's angle of scoliosis. The asymmetric bony construction parameter probably plays a biomechanical role in the progression of scoliosis, which maybe the reason for the asymmetric degeneration of intervertebral disc-endplate.

[Selective treatment of aged osteoporosis thoracolumbar vertebrae burst fracture with balloon kyphoplasty].

OBJECTIVE: To evaluate the effectiveness and the value of balloon kyphoplasty in treating aged osteoporosis thoracolumbar vertebrae burst fracture. METHODS: Between January 2003 and January 2008, 36 thoracolumbar vertebrae burst fracture patients were treated. There were 15 males and 21 females with an average age of 65.4 years (range, 59-72 years). Fourteen cases had no obvious history of trauma, 19 had a history of slight trauma, and 3 had a history of severe trauma. Forty vertebral bodies were involved, including 1 T7, 3 T9, 8 T10, 10 T12, 9 L1, 7 L2, and 2 L4. All patients displayed local pain and osteoporosis by bone density measurement with no neurological symptom of both lower limbs. Balloon kyphoplasty through unilateral (31 cases) or bilateral (5 cases) vertebral pedicles with polymethylmethacrylate was performed at the injection volume of (3.46 +/- 0.86) mL per vertebral body. Before and after operation, the anterior height and posterior height of fractured vertebral body and the sagittal displacement were measured. RESULTS: Two cases had intraoperative cerebrospinal fluid leakage; 1 case had no remission of waist-back pain and pain was released after symptomatic treatment. All 36 patients were followed up 2.3 years on average (range, 1.5-4.0 years). No cement leakage was found with good diffusion of cement on X-ray film. The restoration of the height of vertebral bodies was satisfactory without nerve compression symptoms and other complications. The Visual Analogue Score at last follow-up (2.34 +/- 1.03) was significantly lower than that of preoperation (6.78 +/- 1.21), (P < 0.05). The compressive percentage of anterior height (19.80% +/- 1.03%) of fractured vertebral body after operation was significantly lower than that before operation (25.30% +/- 2.50%), (P < 0.05). There was no significant difference in posterior compressive percentage and sagittal displacement between pre- and post- operation (P > 0.05). CONCLUSION: Based on roentgenographic scores, balloon kyphoplasty is selectively used to treat aged osteoporosis thoracolumbar vertebrae burst fracture, and the radiographic and clinical results were satisfactory.