Mitochondrial respiratory complex I deficiency inhibits brown adipogenesis by limiting heme regulation of histone demethylation.

Mitochondrial functions play a crucial role in determining the metabolic and thermogenic status of brown adipocytes. Increasing evidence reveals that the mitochondrial oxidative phosphorylation (OXPHOS) system plays an important role in brown adipogenesis, but the mechanistic insights are limited. Herein, we explored the potential metabolic mechanisms leading to OXPHOS regulation of brown adipogenesis in pharmacological and genetic models of mitochondrial respiratory complex I deficiency. OXPHOS deficiency inhibits brown adipogenesis through disruption of the brown adipogenic transcription circuit without affecting ATP levels. Neither blockage of calcium signaling nor antioxidant treatment can rescue the suppressed brown adipogenesis. Metabolomics analysis revealed a decrease in levels of tricarboxylic acid cycle intermediates and heme. Heme supplementation specifically enhances respiratory complex I activity without affecting complex II and partially reverses the inhibited brown adipogenesis by OXPHOS deficiency. Moreover, the regulation of brown adipogenesis by the OXPHOS-heme axis may be due to the suppressed histone methylation status by increasing histone demethylation. In summary, our findings identified a heme-sensing retrograde signaling pathway that connects mitochondrial OXPHOS to the regulation of brown adipocyte differentiation and metabolic functions.

Comparative study on the treatment of swine wastewater by VFCW-MFC and VFCW: Pollutants removal, electricity generation, microorganism community.

Swine wastewater, characterized by high organic and nutrient content, poses significant environmental challenges. This study aims to compare the effectiveness of two treatment technologies, namely Vertical Flow Constructed Wetland-Microbial Fuel Cell (VFCW-MFC) and Vertical Flow Constructed Wetland (VFCW), in terms of pollutant removal, electricity generation, and microorganism community dynamics. The results showed that the average removal efficiencies of chemical oxygen demand (COD), ammonia nitrogen, total nitrogen (TN), total phosphorus (TP) and sulfadiazine antibiotics (SDZ) by VFCW-MFC were as high as 94.15%, 95.01%, 42.24%, 97.16% and 82.88%, respectively, which were all higher than that by VFCW. Both VFCW-MFC and VFCW have good tolerance to SDZ. In addition, VFCW-MFC has excellent electrical performance, with output voltage, power density, coulombic efficiency and net energy recovery up to 443.59 mV, 51.2 mW/m3, 52.91% and 2.04 W/(g·s), respectively, during stable operation. Moreover, the microbial community diversity of VFCW-MFC was more abundant, and the species abundance distribution in cathode region was more rich and even than in anode region. At phylum level, the dominant microorganisms in VFCW-MFC included Proteobacteria, Bacteroidota, Firmicutes and Actinobacteriota, which showed good degradation effect on SDZ. Proteobacteria and Firmicutes are also involved in electricity production. Chloroflexi, Proteobacteria and Bacteroidota play a major role in nitrogen reduction.

Efficient removal of Hg0 from cement kiln flue gas using CexFeyOz composite catalyst.

In this study, a kind of CexFeyOz composite with oxygen vacancy structure and strong oxygen storage capacity was prepared by coprecipitation method. Under the condition of no HCl of flue gas, the Hg0 in the flue gas of cement kiln was efficiently and economically removed by using 6-8% oxygen. The results showed that the optimum preparation conditions of the catalyst were Ce-Fe molar ratio of 1-11 and calcination temperature of 550 °C. In addition, the reaction temperature, space velocity, the concentration of O2, SO2, and NO had significant effects on the removal efficiency of Hg0 at different rates. More precisely, at the reaction temperature of 350 °C, low airspeed, high concentration of O2, and low concentration of SO2 and NO, the efficiency reached the highest value. According to XPS results, the elemental valence of the CexFeyOz composite changed after the reaction. The redox pairs of Ce3+-Ce4+ and Fe3+-Fe2+ had the ability to transfer electrons, which enabled more oxygen adsorbed on the catalyst surface to be converted into O2-, leading to the improvement of the oxidation efficiency of Hg0.

Very low frequency three-dimensional beamforming for a miniaturized aperture acoustic vector sensor array.

In this Letter, a three-dimensional beamforming method is proposed for a miniaturized aperture acoustic vector sensor (AVS) array. This method extracts the multipole modes using the AVS array, and then synthesizes the desired beam pattern according to the relation between multipole modes and spherical harmonics. Compared to the spherical harmonics decomposition of the sound field method, the proposed method achieves comparable array gain with higher white noise gain when the distance of adjacent elements d and the wavelength λ satisfy 0.01≤d/λ≤0.2. Experimental results also demonstrate the effectiveness of the proposed three-dimensional beamforming method at very low frequency.

Effective immobilization of Bacillus subtilis in chitosan-sodium alginate composite carrier for ammonia removal from anaerobically digested swine wastewater.

To overcome the easy loss of microorganism, the mass production of sludge and the consumption of aeration energy during biological treatment of anaerobically digested swine wastewater, this study used chitosan-sodium alginate composite carrier to prepare immobilized bacteria pellets. The heterotrophic bacteria tolerant to high concentrations of ammonia nitrogen were isolated and the conditions for immobilizing bacteria were optimized. The performance of immobilized bacteria pellets to remove ammonia nitrogen from ADSW was determined and the corresponding mechanism was investigated. Results showed that the isolated bacteria were Bacillus subtilis, and the optimal conditions to prepare the immobilized bacteria pellets by response surface methodology tests were sodium alginate of 0.84% (m/V), chitosan of 0.22% (m/V), embedding time of 32 min and embedding amount of 15% (V/V). In ADSW treatment, at pH 6, 20 g/L of the immobilized bacteria pellets removed 96.5% of ammonia nitrogen. Both adsorption and microbial action contributed to ammonia nitrogen removal, and their contributions were 54.3% and 42.2%, respectively. Compared with the immobilized bacteria pellets using chitosan-sodium alginate as carrier, the one using mono alginate as carrier had a weaker ability to remove ammonia nitrogen, with a removal efficiency of 67.4%. The main mechanism was the formation of polyelectrolyte membrane by the connection between amino groups of chitosan and carboxyl groups of sodium alginate, which stabilized the immobilized bacteria pellets and prolonged their service life. To sum up, the immobilized bacteria pellets using chitosan-sodium alginate as an embedding agent have a promising prospect in ammonia nitrogen removal from wastewater.

Insight into sludge dewatering by advanced oxidation using persulfate as oxidant and Fe2+ as activator: Performance, mechanism and extracellular polymers and heavy metals behaviors.

This study established a Fe2+/persulfate oxidation system to dewater sludge in WWTPs. Dewatering performance, persulfate consumption and the variations of sludge pH, TN and TP during dewatering process were monitored. EPS and ζ-potential behaviors for ameliorating sludge dewatering was investigated. Transformation, leaching toxicity and environmental risk of heavy metals in sludge during dewatering were determined. Results demonstrated that after treated by Fe2+/persulfate oxidation system with 0.6 mmol/g-VS of persulfate at Fe2+/persulfate molar ratio 0.6, WC decreased to 53.5% and SCST increased to 4.15, which implied an excellent improvement of sludge dewatering. The fast persulfate consumption, the decrease of sludge pH and the increase of TN illustrated the positive effects of Fe2+ in activating persulfate and the decomposition of EPS by the activation products, SO4•- and •OH. Another product (Fe3+) generated during persulfate activation could decrease the content of phosphorus-containing matter (released from EPS decomposition) through the precipitation reaction with PO43-. The decrease of TOC and UV-254 happened in HPO-A, HPO-N and TPI-A organic substance of EPS (mainly contained in TB-EPS fraction) indicated that the destruction of hydrophobic organic matter of EPS would stimulate the release of bound water, which was beneficial to dewater sludge. The largest protein loss in TB-EPS (from 24.5 to 10.7 mg/L) indicated that the effective decomposition of TB-EPS could significantly ameliorate sludge dewatering. The increase of ζ-potential indicated the degradation of organic matter in EPS with negative charge. To sum up, the destruction of protein-like substances in hydrophobic organic matter of TB-EPS was the main mechanism for improving sludge dewatering by Fe2+/persulfate oxidation system. 3D-EEM fluorescence spectroscopy analysis proved that these protein-like substances were mainly tryptophan protein and humic acid. Moreover, due to the disruption of EPS, the contents of heavy metals in sludge, and their leaching toxicity and environmental risk were reduced. Therefore, Fe2+/persulfate oxidation system has potential and application prospects to improve sludge dewatering and optimize sludge management in WWTPs.

Performance and kinetics of benzo(a)pyrene biodegradation in contaminated water and soil and improvement of soil properties by biosurfactant amendment.

As a hydrophobic pollutant, benzo(a)pyrene (BaP) is difficult to be degraded by microbes due to its poor water solubility. To improve its water solubility, this study harvested a biosurfactant from swine wastewater. The role of the biosurfactant in BaP biodegradation in contaminated water and soil were investigated. The biodegradation kinetics of BaP in contaminated water and the improvement of soil properties were determined. Results showed that critical micelle concentration (CMC) of the biosurfactant was 46.8 mg/L. The biosurfactant has a high pH stability in range of 3-9 and a strong salt stability in NaCl concentration range of 0-20%. At concentrations of 1, 2, 3, 4 and 5 CMC, the biosurfactant increased BaP water solubility by 1.4, 2.6, 4.0, 5.2 and 6.6 times. BaP biodegradation in contaminated water was effectively promoted by the biosurfactant, and the concentrations of BaP in sludge phase decreased to 1.015 mg/L (47.9% decrement) and 0.675 mg/L (65.4% decrement) when the dosed biosurfactant were 1 and 3 CMC, respectively. The biodegradation kinetics of BaP in contaminated water by the biosurfactant fitted well with the two-compartment kinetic model well (R2 > 0.90). For the bioremediation of BaP contaminated soil, adding 0.1%-0.5% (w/w) biosurfactant biodegraded 39.2%-84.8% of BaP, while the control without biosurfactant was 24.2%. In addition, the application of the biosurfactant significantly improved the properties of the contaminated soil, behaved as the increase in microbial quantity, water holding capacity (WHC) and dehydrogenase (DH) activity of the soil. To sum up, the biosurfactant facilitated the BaP biodegradation and can be effectively used in in-site remediation of polycyclic aromatic hydrocarbons (PAHs) (BaP in this study) contaminated water and soil.

Enhancement of ethylbenzene removal from contaminated gas and corresponding mechanisms in biotrickling filters by a biosurfactant from piggery wastewater.

This study prepared a biosurfactant by using piggery wastewater to enhance ethylbenzene removal from contaminated gas in a biotrickling filter (BTF). Experiments were conducted to investigate the enhancement of ethylbenzene removal and the biofilm characteristics in present of the biosurfactant. Results demonstrated that the optimal biosurfactant concentration was 0.1 CMC and the corresponding ethylbenzene removal rate was 87.2%, much higher than that (68.9%) achieved in free of biosurfactant. The inlet ethylbenzene concentration and the empty bed residence time (EBRT) affected ethylbenzene removal as well. In present of 0.1 CMC of biosurfactant, ethylbenzene removal rate decreased from 87.2% to 72.2% with the increasing inlet ethylbenzene from 1000 to 2200 mg/m3, and decreased from 91.1% to 42.7% with the EBRT shorten from 30 to 7.5 s. For the enhancement mechanisms of ethylbenzene removal in BTF, the biosurfactant changed the contents of extracellular polymers (EPS) and decreased negative surface charge of the biofilm in the BTF, which improved the mass transfer of ethylbenzene to biofilm and facilitated the aggregation of microbes, and further improved the removal of ethylbenzene. All in all, the biosurfactant would be a feasible way to enhance the removal of ethylbenzene by the BTF.

Removal of benzo(a)pyrene in polluted aqueous solution and soil using persulfate activated by corn straw biochar.

An activator, corn straw biochar, was produced and applied in persulfate-based oxidation to remove benzo(a)pyrene (BaP) in polluted aqueous solution and soil. Polluted aqueous solution remediation results showed that at pH 7, approximately 88.4% of BaP was removed by 10 mM of persulfate activated by 1.6 g/L of biochar, and degradation played a dominant role. Polluted soil remediation results demonstrated that the activated persulfate solution (at 9 g/L) by biochar (at 3 wt% of soil) can remove 93.2% of BaP. In remediation of BaP-polluted soil, increasing biochar dosage and persulfate concentration accelerated BaP degradation to some extent, while excessive biochar or persulfate inhibited the degradation of BaP probably due to the unnecessary SO4- consumption. The biochar-activated persulfate oxidation reflected a good performance in tolerating the influences of background electrolytes (such as HCO3-, Cl-, and humic acid (HA)) in soil on BaP remediation. In addition, in the removal of BaP by the oxidation systems activated by biochar, persulfate was proved as a superior oxidant compared to peroxymonosulfate and H2O2, and the removal efficiencies of BaP were 93.2%, 86.5%, and 84.4% under the same treatment condition. To sum up, the biochar-activated persulfate oxidation would be a potential application in remediation of BaP-polluted aqueous solution and soil.

Insight into the improvement of dewatering performance of waste activated sludge and the corresponding mechanism by biochar-activated persulfate oxidation.

A novel activator, corn biochar, was produced to activate persulfate to dewater waste activated sludge (WAS). Results demonstrated that the biochar-activated persulfate oxidation can effectively improve the dewatering performance of WAS. After treating WAS by biochar-activated persulfate oxidation (biochar dosage: 2.1 g/L, persulfate concentration: 7.5 mM) at the original WAS pH, standardized-capillary suction time (SCST) increased to 4.21 times and moisture content (MC) decreased to 43.4%, indicating an excellent performance of WAS dewatering. The decrease of residual persulfate with the increasing biochar dosage during WAS dewatering process illustrated that the role of persulfate in improving WAS dewatering was because of the biochar activation. The behaviors of extracellular polymers (EPS) proved that the protein in tightly bound EPS (TB-EPS) linked to WAS dewatering, and its content significantly reduced to 10.5 mg/g-volatile solids (VS) after WAS treatment. Three-dimensional fluorescence spectroscopy for EPS once again proved that the disintegration of tryptophan protein and humic acid (hydrophobic organic substances in EPS) was responsible for the improvement of WAS dewatering. To sum up, the biochar-activated persulfate oxidation was a feasible application in improving WAS dewatering.

[Bacterial Community Shifts and Nitrogen Removal Characteristics for a SNAD Process Treating Anaerobic Digester Liquor of Swine Wastewater (ADLSW) in a Continuous-Flow Biofilm Reactor (CFBR)].

To realize a simultaneous partial nitrification, ANAMMOX (anaerobic ammonium oxidation), and denitrification (SNAD) process treating anaerobic digester liquor of swine wastewater (ADLSW) in a continuous-flow biofilm reactor (CFBR), we first gradually increased the influent ammonium (NH4+-N) concentration, and then enhanced the ADLSW ratio in the influent during operation; dissolved oxygen (DO) was controlled at (0.4±0.1) mg·L-1 by adjusting the air flow rate, and the temperature was kept at (30±1)℃. Meanwhile, high-throughput sequencing and quantitative PCR (polymerase chain reaction) techniques were used to analyze the bacterial community shifts and the amount of dominant nitrogen removal bacteria. The results demonstrated that a successful start-up of the SNAD process was accomplished in 150 d, and replacement of the actual biogas slurry was completed in 298 d. The effluent (NO3--N+NO2--N)/ΔNH4+-N value was less than 0.11, and the average removal rates of NH4+-N and TN (total nitrogen) increased to 63.26% and 55.71%, respectively. Moreover, high-throughput sequencing results demonstrated that the dominant microbial populations at phylum level were Chloroflexi (with a relative abundance of 50.78%), Proteobacteria (13.34%), and Planctomycetes (9.26%). The relative abundance of Nitrosomonas increased from 1.55% to 1.98%. In addition, the relative abundance of Candidatus_Brocadia and Candidatus_Kuenenia increased from 0.01% and (<0.01%) to 4.66% and 4.18%, respectively, and the relative abundance of Denitratisoma increased from (<0.01%) to 2.06%. Meanwhile, qPCR analysis showed that the amounts of ammonia-oxidizing bacteria, ANAMMOX, and denitrifying bacteria increased significantly compared with the inoculated sludge. An efficient and stable nitrogen removal rate can be achieved, and the follow-up processing cost can be reduced, by application of the SNAD treatment process for ADLSW.

Passive Detection of Ship-Radiated Acoustic Signal Using Coherent Integration of Cross-Power Spectrum with Doppler and Time Delay Compensations.

Passive sonar is widely used for target detection, identification and classification based on the target radiated acoustic signal. Under the influence of Doppler, generated by relative motion between the moving target and the sonar array, the received ship-radiated acoustic signals are non-stationary and time-varying, which has a negative effect on target detection and other fields. In order to reduce the influence of Doppler and improve the performance of target detection, a coherent integration method based on cross-power spectrum is proposed in this paper. It can be concluded that the frequency shift and phase change in the cross-power spectrum obtained by each pair of data segments can be corrected with the compensations of time scale (Doppler) factor and time delay. Moreover, the time scale factor and time delay can be estimated from the amplitude and phase of the original cross-power spectrum, respectively. Therefore, coherent integration can be implemented with the compensated cross-power spectra. Simulation and experimental data processing results show that the proposed method can provide sufficient processing gains and effectively extract the discrete spectra for the detection of moving targets.

Insight into dewatering behavior and heavy metals transformation during waste activated sludge treatment by thermally-activated sodium persulfate oxidation combined with a skeleton builder-wheat straw biochar.

This work focused on dewatering performance and heavy metals (HMs) transformation during waste activated sludge (WAS) treatment by employing thermally-activated sodium persulfate (SPS) oxidation combined with a biochar made of wheat straw (WS-BC). Results demonstrated that the combined treatment was an efficient way to improve WAS dewatering, especially when SPS and WS-BC dosages were adjusted to 120 and 150 mg/g-volatile solids (VS), respectively. After being treated at 70 °C without pH adjustment, standardized-capillary suction time (SCST) was increased to 5.03, centrifuged weight reduction (CWR) was increased to 86.8% and moisture content (MC) was decreased to 42.6%, indicating an excellent dewatering performance. The underlying mechanism identified were: (1) SPS oxidation disintegrated extracellular polymers (EPS) at high temperature, thereby releasing EPS-bound water; (2) WS-BC acted as a skeleton builder conducive to form porous structure and provide free water release channels in WAS, which was favorable to improve dewatering properties of WAS; (3) thermally-activated SPS oxidation significantly improved the solubilization and reduced the leaching toxicity of HMs in WAS; and (4) the following WS-BC treatment further reduced the leaching toxicity of HMs in WAS. Therefore, the combined technology might be a promising strategy to improve WAS dewatering and reduce HMs risks in WAS.

The Patatin-Like Phospholipase Domain Containing Protein 7 Facilitates VLDL Secretion by Modulating ApoE Stability.

BACKGROUND AND AIMS: The regulation of hepatic very-low-density lipoprotein (VLDL) secretion is vital for lipid metabolism whose pathogenetic status is involved in fatty liver disease and dyslipidemia seen in hepatic steatosis. Accumulated evidence suggest that apolipoprotein E (ApoE) is closely related to hepatic VLDL secretion. Here, we report that the expression of patatin-like phospholipase domain containing protein 7 (PNPLA7) is strongly induced by hepatic steatosis and positively correlates with plasma triacylglycerol (TAG) levels in the human subjects, whereas the role of PNPLA7 in hepatic VLDL secretion is unknown. APPROACH AND RESULTS: Herein, with genetic manipulation in the mice, the deficiency of hepatic PNPLA7 expression resulted in reduced VLDL secretion accompanied by enhanced hepatic lipid accumulation and decreased hepatic ApoE expression. Furthermore, knockdown of PNPLA7 in the livers of the db/db mice also resulted in significant reduction in plasma TAG level but aggravated hepatic steatosis. Importantly, we observed that PNPLA7 interacted with ApoE and presumably at the site of endoplasmic reticulum. Mechanistically, we have shown that PNPLA7 could modulate polyubiquitination and proteasomal-mediated degradation of ApoE. Overexpressed ApoE restored the impaired VLDL-TAG metabolism in PNPLA7-knockdown primary hepatocytes. CONCLUSION: PNPLA7 plays a critical role in regulating hepatic VLDL secretion by modulating ApoE stability through its interaction with ApoE.

Performances and mechanisms of sludge dewatering by a biopolymer from piggery wastewater and application of the dewatered sludge in remediation of Cr(VI)-contaminated soil.

In this study, a biopolymer was harvested from piggery wastewater to treat biological sludge. Effectiveness of the combination of polyaluminum chloride (PAC) and this biopolymer in sludge dewatering was investigated and the dewatering mechanism was discussed. Results showed that as high as 3.11 g of biopolymer can be harvested from 1 L of piggery wastewater by cultivating Bacillus megaterium. After treated by PAC with a dosage of 1.5 g/L at pH point of 7.5, specific resistance to filtration (SRF), moisture content (MC), settled volume after 30 min (SV30) and capillary suction time (CST) of the sludge were decreased to 3.4 × 1012 m/kg, 84.5%, 79.8% and 65 s, respectively, and dry solid (DS) was increased to 21.4%, indicated that sludge dewatering was obviously enhanced by PAC. After further treated by 2 g/L of the biopolymer, SRF, MC, SV30 and CST were further decreased to 2.1 × 1012 m/kg, 59.8%, 55.6% and 39 s, respectively, and DS was increased to 28.6%, indicated that sludge dewatering was further enhanced by the biopolymer. For the enhancing mechanism, on the one hand, the extracellular polymeric substances (EPS) was significantly disintegrated to release binding bound water, which was facilitating sludge dewatering; on the other hand, the synergistic effect of PAC coagulation and biopolymer flocculation, including charge neutralization and bridge-aggregation, were favorable to sludge dewatering. Additionally, we found that the dewatered sludge was helpful for remediation of chromium (Cr)(VI)-contaminated soil by raising soil pH and decreasing bioavailability of Cr(VI) in the soil, after remediated by 75 g/kg of the dewatered sludge for 60 days, the soil pH was increased from its initial value of 4.32-8.52, and the residue Cr(VI) in the soil extract was appeared as 2.2 mg/L.

Transformation of heavy metals and dewaterability of waste activated sludge during the conditioning by Fe2+-activated peroxymonosulfate oxidation combined with rice straw biochar as skeleton builder.

This work investigated the improvement performances and mechanisms of waste activated sludge (WAS) dewaterability and the transformation behavior of heavy metals (HMs, including Cu, Zn, Pb, Cd and Cr) by jointly conditioning of Fe2+-activated peroxymonosulfate (PMS) oxidation and rice straw biochar (RS-BC). Experimental results showed that at original WAS pH of 6.5, the joint conditioning was the most effective when PMS dosage was 0.6 mmol·(g-volatile solids (VS))-1, Fe2+/PMS molar ratio was 0.6 and RS-BC dosage was 120 mg·(g-VS)-1. Under this condition, the lowest moisture content (MC) was 38.5% and the standardized-capillary suction time (SCST) was as high as 8.74. For the improvement mechanism, Fe2+-activated PMS oxidation can significantly disintegrate the extracellular polymeric substances (EPS) composing WAS to release EPS-bound water, and the RS-BC was helpful to form porous structures to improve WAS compressibility, facilitating the subsequent dewatering. In addition, Fe2+-activated PMS oxidation can obviously improve the solubilization and reduce the leaching toxicity of Cu, Zn, Pb, Cd and Cr, which was further enhanced by RS-BC. Therefore, the joint application of Fe2+-activated PMS oxidation and RS-BC can be a feasible way to improve WAS dewaterability and reduce HMs risk during WAS dewatering.

Effect of biosurfactant on ammonia removal from anaerobically digested swine wastewater by multi soil layering treatment bioreactors.

A biosurfactant was harvested from anaerobically digested swine wastewater (ADSW) and employed to enhance ammonia removal in a comparative study using two multiple soil layer bioreactors (MSLs). Results showed that toxicity of the biosurfactant to microorganisms was negligible within the experimental concentration range. Optimal dose of the biosurfactant in MSLs to remove ammonia from ADSW was 0.1 CMC (Critical Micelle Concentration) under different hydraulic loading rate (HLR). For instance, when the HLR was adjusted as 80, 120, 160, and 200 L/(m2·d), the average ammonia removal efficiency in MSL without biosurfactant addition was appeared as 85.6%, 89.2%, 85.2% and 84.1%, respectively, after enhanced by 0.1 CMC of the biosurfactant under the same condition, the average ammonia removal efficiency was improved to 90.1%, 92.6%, 90.3%, and 87.4%, respectively. Inlet ammonia concentration obviously affected ammonia removal, the average ammonia removal efficiency increased rapidly to 93.0% and 89.1% in MSLs (with and without biosurfactant) along with the increasing inlet ammonia concentration from 800 mg/L to 1000 mg/L, and subsequently dropped to 78.9% and 79.7% with a further increase in the inlet ammonia concentration to 1400 mg/L. These results showed that the biosurfactant effectively enhanced ammonia removal by using MSL. Thus, the construction of MSL represented an effective means of reducing ammonia pollution caused by swine wastewater, and the use of biosurfactant was assuredly a promising and feasible option for enhancing the biological activity in MSL bioreactor.

Carbon-based magnetic nanocomposite as catalyst for persulfate activation: a critical review.

The activation of persulfate to produce active radicals has been attracting wide attention in environmental remediation fields. Among various catalysts, non-metal carbocatalysts and carbon-based composites have shown attractive prospects given that they are environmental-friendly, highly efficient, abundant, and diverse. In this paper, the use of carbon-based magnetic nanocomposites as catalysts for persulfate activation was reviewed and discussed. The preparation methods of carbon-based magnetic nanocomposites were first briefly summarized. Subsequently, the use of activated carbon, carbon nanotubes, graphene oxide, biochar, and nanodiamond-based magnetic composites to activate persulfate was discussed, respectively. A synergetic effect between carbon materials and magnetic nanoparticles facilitated the activation process because of the increased electron transfer capacity, good dispersity of magnetic nanoparticles, and good repeatability and separability. Both radical and non-radical pathways were detected in the activation processes, but the specific mechanisms were greatly influenced by the components of the catalyst and solution conditions. And fundamental studies were needed to clarify the inner mechanisms of the process. In the end, strategies for enhancing the catalytic performances of carbon-based magnetic nanocomposites were suggested. It is expected that this review will provide some inspirations for developing highly efficient and green catalyst, as well as sulfate radical-based advanced oxidation technology for the remediation water environment.

Feasibility investigation of a multi soil layering bioreactor for domestic wastewater treatment.

In this study, a multi soil layering (MSL) bioreactor was constructed to treat synthetic domestic wastewater. Effects of hydraulic loading rate (HLR) on the performance of the MSL bioreactor for synthetic domestic wastewater treatment were investigated. Results showed that the MSL bioreactor exhibited a strong adaptability on the variation of HLR, when the HLR was adjusted to 400 L·m-2·d-1, average removal efficiencies of chemical oxygen demand (COD), ammonia, total nitrogen (TN), and total phosphorus (TP) reached 93.4%, 94.9%, 80.4%, and 94.7%, respectively, which meet to the 1A discharge standard of the Discharge standard of pollutants for municipal wastewater treatment plant (GB 18918-2002). In the treatment process by the MSL bioreactor, biological decomposition and biotransformation processes of microorganisms was the most important pathway for COD, ammonia, and TN removal, while TP was removed by the chemical reaction with ferric ion. Nitrobacteria, ciliate, rotifer and epistylis were in large numbers in the operating phase, indicated that the biofilm was matured with a high quality and the MSL bioreactor was effective for domestic wastewater treatment.