ABSTRACT
Al/Mo/SiC periodic and aperiodic multilayers were optimized and deposited on high groove density gratings to achieve broadband efficiency in the extreme ultraviolet (EUV). Grating efficiencies were measured by monochromatic synchrotron radiation under 5° and 45° incident angles in the wavelength ranges 17-25 nm and 22-31 nm, respectively. We study the influence of the number of deposited periods on the initial trapezoidal profile and the EUV diffraction efficiency. We propose models of periodic and aperiodic coatings based on a combination of characterizations and compare rigorous coupled-wave analysis (RCWA) simulations with experimental data. We demonstrate the possibility to select the optimal balance between peak efficiency and bandwidth by adjusting the number of periods in the case of periodic multilayer grating. We also report unprecedented broadband diffraction efficiency with an Al/Mo/SiC aperiodic multilayer grating.
ABSTRACT
Sclareol, an antifungal specialized metabolite produced by clary sage, Salvia sclarea, is the starting plant natural molecule used for the hemisynthesis of the perfume ingredient ambroxide. Sclareol is mainly produced in clary sage flower calyces; however, the cellular localization of the sclareol biosynthesis remains unknown. To elucidate the site of sclareol biosynthesis, we analyzed its spatial distribution in the clary sage calyx epidermis using laser desorption/ionization mass spectrometry imaging (LDI-FTICR-MSI) and investigated the expression profile of sclareol biosynthesis genes in isolated glandular trichomes (GTs). We showed that sclareol specifically accumulates in GTs' gland cells in which sclareol biosynthesis genes are strongly expressed. We next isolated a glabrous beardless mutant and demonstrate that more than 90% of the sclareol is produced by the large capitate GTs. Feeding experiments, using 1-13C-glucose, and specific enzyme inhibitors further revealed that the methylerythritol-phosphate (MEP) biosynthetic pathway is the main source of isopentenyl diphosphate (IPP) precursor used for the biosynthesis of sclareol. Our findings demonstrate that sclareol is an MEP-derived diterpene produced by large capitate GTs in clary sage emphasing the role of GTs as biofactories dedicated to the production of specialized metabolites.
ABSTRACT
Precipitates in an austenitic stainless steel fabricated via any Additive Manufacturing (AM), or 3D printing, technique have been widely reported to be only Mn-Si-rich oxides. However, via Transmission Electron Microscopy (TEM) studies on a 316L stainless steel, we show that non-oxide precipitates (intermetallics, sulfides, phosphides and carbides) can also form when the steel is fabricated via Laser Metal Deposition (LMD)-a directed energy deposition-type AM technique. An investigation into their origin is conducted with support from precipitation kinetics and finite element heat transfer simulations. It reveals that non-oxide precipitates form during solidification/cooling at temperatures ≥ 0.75Tm (melting point) and temperature rates ≤ 105 K/s, which is the upper end of the maximum rates encountered during LMD but lower than those encountered during Selective Laser Melting (SLM)-a powder-bed type AM technique. Consequently, non-oxide precipitates should form during LMD, as reported in this work, but not during SLM, in consistency with existing literature.
ABSTRACT
Scanning Electron Microscopes (SEMs) often generate images with a shaded appearance which gives a natural 3D impression. Ergo, quite a few methods to reconstruct the 3D surface topography from these using shape-from-shading methods are available in the literature. Here, a novel approach is discussed which uses BackScatter Electron (BSE) images from multiple detectors to reconstruct the topography. Classically, algorithms exist which resort to a quad-BSE detector setup. However, other detector configurations are often found in SEMs. A set of images of these non-conforming detectors still contains enough information to allow for reconstruction, but requires a more general algorithm to do so. This article discusses a method based on a modal decomposition of the principal image components. The resulting method is shown to be efficient and independent of the number of detectors or their orientation. In fact, the orientation is identified as part of the algorithm and thus requires very little calibration.
