Triboelectric charge saturation on single and multiple insulating particles in air and vacuum.

Triboelectric charge transfer is complex and depends on contact properties such as material composition and contact area, as well as environmental factors including humidity, temperature, and air pressure. Saturation surface charge density on particles is inversely dependent on particle size and the number of nearby particles. Here we show that electrical breakdown of air is the primary cause of triboelectric charge saturation on single and multiple electrically insulating particles, which explains the inverse dependence of surface charge density on particle size and number of particles. We combine computational simulations with experiments under controlled humidity and pressure. The results show that the electric field contribution of multiple particles causes electrical breakdown of air, reducing saturation surface charge density for greater numbers of particles. Furthermore, these results show that particles can be discharged in a low pressure environment, yielding opportunities for improved industrial powder flows and dust mitigation from surfaces.

Numerical Solution of the Electric Field and Dielectrophoresis Force of Electrostatic Traveling Wave System.

Electrostatic traveling wave (ETW) methods have shown promising performance in dust mitigation of solar panels, particle transport and separation in in situ space resource utilization, cell manipulation, and separation in biology. The ETW field distribution is required to analyze the forces applied to particles and to evaluate ETW design parameters. This study presents the numerical results of the ETW field distribution generated by a parallel electrode array using both the charge simulation method (CSM) and the boundary element method (BEM). A low accumulated error of the CSM is achieved by properly arranging the positions and numbers of contour points and fictitious charges. The BEM can avoid the inconvenience of the charge position required in the CSM. The numerical results show extremely close agreement between the CSM and BEM. For simplification, the method of images is introduced in the implementation of the CSM and BEM. Moreover, analytical formulas are obtained for the integral of Green's function along boundary elements. For further validation, the results are cross-checked using the finite element method (FEM). It is found that discrepancies occur at the ends of the electrode array. Finally, analyses are provided of the electric field and dielectrophoretic (DEP) components. Emphasis is given to the regions close to the electrode surfaces. These results provide guidance for the fabrication of ETW systems for various applications.

Toward the utilisation of resources in space: knowledge gaps, open questions, and priorities.

There are many open science questions in space resource utilisation due to the novelty and relative immaturity of the field. While many potential technologies have been proposed to produce usable resources in space, high confidence, large-scale design is limited by gaps in the knowledge of the local environmental conditions, geology, mineralogy, and regolith characteristics, as well as specific science questions intrinsic to each process. Further, the engineering constraints (e.g. energy, throughput, efficiency etc.) must be incorporated into the design. This work aims to summarise briefly recent activities in the field of space resource utilisation, as well as to identify key knowledge gaps, and to present open science questions. Finally, future exploration priorities to enable the use of space resources are highlighted.

Standard method for performing positron emission particle tracking (PEPT) measurements of froth flotation at PEPT Cape Town.

Positron emission particle tracking (PEPT) is a technique for measuring the motion of tracer particles in systems of flow such as mineral froth flotation. An advantage of PEPT is that tracer particles with different physical properties can be tracked in the same experimental system, which allows detailed studies of the relative behaviour of different particle classes in flotation. This work describes the standard operating protocol developed for PEPT experiments in a flotation vessel at PEPT Cape Town in South Africa. A continuously overflowing vessel with constant air recovery enables several hours of data acquisition at steady state flow and consistent flotation conditions. Tracer particles are fabricated with different coatings to mimic mineral surface hydrophobicity and size, and a data treatment derived from a rotating disk study is utilized to produce high frequency (1 kHz) location data relative to the tracer activity. Time averaging methods are used to represent the Eulerian flow field and occupancy of the tracer behaviour based on voxel schemes in different co-ordinate systems. The average velocity of the flow in each voxel is calculated as the peak of the probability density function to represent the peak of asymmetrical or multimodal distributions.•A continuously overflowing flotation vessel was developed for extended data acquisition at steady state flow.•The data treatment enabled the direct comparison of different particle classes in the flotation vessel.•The solids flow fields was described by the probability density function of tracer particle velocity measured in different voxel schemes.

Apatite enrichment by rare earth elements: A review of the effects of surface properties.

Apatite subspecies depend on their halogen and hydroxyl content; chlorapatite, hydroxylapatite and fluorapatite, with additional substitution of other elements within the lattice such as rare earth elements (REE), sodium, strontium and manganese also possible. Rare earth elements are vital to green and emerging technologies, with demand set to outstrip supply. Apatite provides a possible future source of REE. Processing rare earth deposits is often complex, with surface behaviour having a significant effect on the optimization of a process flow sheet. The effect of enrichment of natural apatite and the doping of synthetic apatite on surface behaviour can be determined by measuring the zeta potential and the isoelectric point of the mineral. In this paper, we review zeta potential studies of natural and synthetic apatite to determine the effect of elemental enrichment on surface behaviour. Fifty three studies of natural apatite and forty four studies of synthetic apatite were reviewed. The isoelectric point of apatite varied from pH 1 to pH 8.7, with studies of apatite specified to be >90% pure reducing the variation to pH 3 to pH 6.5. Of the four studies of rare earth enriched apatite found, three had IEP values between pH 3 and pH 4. A study of synthetic apatite showing enrichment of between 1 and 10% by the REE europium does not affect surface behaviour. However, no studies were found that investigated the effect of common REE processing reagents on REE enriched apatite zeta potentials. Therefore, in addition to comparing previous studies we also therefore present new zeta potential measurements of apatite from a REE enriched deposit under water and common flotation collector conditions. The IEP value of this apatite under water conditions was at pH 3.6, shifting to <3.5 under both hydroxamic acid and betacol conditions. When compared to previous studies, the behaviour of REE enriched apatite under collector conditions is similar to non-REE apatite. This result could be important for future processing of apatite enriched with REE, and therefore global apatite and rare earth supply.

Measurements of interactions between particles and charged microbubbles using a combined micro- and macroscopic strategy.

We report the use of atomic force microscopy (AFM) to study the interactions between silica glass colloidal probes and charged microbubbles created using one of two different surfactants: anionic sodium dodecyl sulfate (SDS) and cationic dodecyl trimethylammonium bromide (DTAB) in an aqueous environment. On close approach between the glass probe and a SDS microbubble, an appreciable repulsive force was observed prior to contact. This was not observed when using a DTAB microbubble, where only attractive forces were observed prior to contact. zeta-potential analysis showed that silica surfaces are negatively charged across the pH range of 3-10 when surfactant is not present. Addition of SDS did not alter the zeta-potential significantly, indicating that adsorption onto the particle surface did not occur. Conversely, the addition of DTAB decreased the negativity of the zeta-potential, reversing the sign, indicating that adsorption had occurred. This analysis was used in the removal of fine particles from suspension using charged microbubbles. Silica particles were recovered using positively charged microbubbles from DTAB but not when using negatively charged microbubbles generated from SDS. Taken together, the data suggest that repulsive long-range interactions were responsible for the selective attachment of silica particles to microbubbles in a charge-dependent manner.