ABSTRACT
The main goal of the presented study was to design a biosensor-based system for epinephrine (EP) detection using a poly-thiophene derivative and tyrosinase as a biorecognition element. We compared two different electroanalytical techniques to select the most prominent technique for analyzing the neurotransmitter. The prepared biosensor system exhibited good parameters; the differential pulse (DPV) technique presented a wide linear range (1-20 µM and 30-200 µM), with a low detection limit (0.18 nM and 1.03 nM). In the case of chronoamperometry (CA), a high signal-to-noise ratio and lower reproducibility were observed, causing a less broad linear range (10-200 µM) and a higher detection limit (125 nM). Therefore, the DPV technique was used for the calculation of sensitivity (0.0011 µA mM-1 cm-2), stability (49 days), and total surface coverage (4.18 × 10-12 mol cm-2). The biosensor also showed very high selectivity in the presence of common interfering species (i.e. ascorbic acid, uric acid, norepinephrine, dopamine) and was successfully applied for EP determination in a pharmaceutical sample.
ABSTRACT
The study of neurotransmitters and stress hormones allows the determination of indicators of the current stress load in the body. These species also create a proper strategy of stress protection. Nowadays, stress is a general factor that affects the population, and it may cause a wide range of serious disorders. Abnormalities in the level of neurohormones, caused by chronic psychological stress, can occur in, for instance, corporate employees, health care workers, shift workers, policemen, or firefighters. Here we present a new nanomaterials-based sensors technology development for the determination of neurohormones. We focus on fluorescent sensors/biosensors that utilize nanomaterials, such as quantum dots or carbon nanomaterials. Nanomaterials, owing to their diversity in size and shape, have been attracting increasing attention in sensing or bioimaging. They possess unique properties, such as fluorescent, electronic, or photoluminescent features. In this Review, we summarize new trends in adopting nanomaterials for applications in fluorescent sensors for neurohormone monitoring.
ABSTRACT
Sensors and biosensors have found applications in many areas, e.g., in medicine and clinical diagnostics, or in environmental monitoring. To expand this field, nanotechnology has been employed in the construction of sensing platforms. Because of their properties, such as high surface area to volume ratio, nanofibers (NFs) have been studied and used to develop sensors with higher loading capacity, better sensitivity, and faster response time. They also allow to miniaturize designed platforms. One of the most commonly used techniques of the fabrication of NFs is electrospinning. Electrospun NFs can be used in different types of sensors and biosensors. This review presents recent studies concerning electrospun nanofiber-based electrochemical and optical sensing platforms for the detection of various medically and environmentally relevant compounds, including glucose, drugs, microorganisms, and toxic metal ions.
Subject(s)
Biosensing Techniques , Nanofibers/chemistry , Nanotechnology/methods , Electrochemistry , Glucose/analysisABSTRACT
The results presented in this paper show how the optical properties and colloidal stability of quantum dots (QDs) vary depending on pH conditions. For this investigation, as-synthesized hydrophobic CdSe/CdS QDs were transferred to an aqueous medium by surface modification with 3-mercaptopropionic acid. The ligand exchange procedure was applied under three different pH conditions: acidic, neutral and alkaline, to obtain three kinds of hydrophilic QDs dispersed in phosphate buffer. The efficiency of the functionalization of QDs was estimated based on the changes in ABS and the highest value was obtained under acidic conditions (45%). The efficiency of photoluminescence (PL) was also best preserved under these conditions, although it was 30 times less than the PL of hydrophobic QDs. Then, all three kinds of hydrophilic QDs were dispersed in solutions with a wide range of pH (2-12) and investigated by absorbance and PL measurements. The results show that QDs subjected to a ligand exchange procedure are characterized by intensive PL at the selected pH values, which correspond to pKa of the ligand. This phenomenon is independent of the pH at which the ligand exchange procedure is conducted. Moreover, it was found that the PL intensity is preserved during the experiment for QDs functionalized under neutral conditions, whereas it decreases for acidic and increases for alkaline conditions.
ABSTRACT
In this review we present polymeric materials for (bio)sensor technology development. We focused on conductive polymers (conjugated microporous polymer, polymer gels), composites, molecularly imprinted polymers and their influence on the design and fabrication of bio(sensors), which in the future could act as lab-on-a-chip (LOC) devices. LOC instruments enable us to perform a wide range of analysis away from the stationary laboratory. Characterized polymeric species represent promising candidates in biosensor or sensor technology for LOC development, not only for manufacturing these devices, but also as a surface for biologically active materials' immobilization. The presence of biological compounds can improve the sensitivity and selectivity of analytical tools, which in the case of medical diagnostics is extremely important. The described materials are biocompatible, cost-effective, flexible and are an excellent platform for the anchoring of specific compounds.
