ABSTRACT
This paper discusses the challenges in characterizing electromagnetic (EM) waves propagating through inhomogeneous media, such as reinforced cement concrete and hot mix asphalt. Understanding the EM properties of materials, including their dielectric constant, conductivity, and magnetic permeability, is crucial to analyzing the behavior of these waves. The focus of this study is to develop a numerical model for EM antennas using the finite difference time domain (FDTD) method, and to gain a deeper understanding of various EM wave phenomena. Additionally, we verify the accuracy of our model by comparing its results with experimental data. We analyze several antenna models with different materials, including the absorber, high-density polyethylene and perfect electrical conductors, to obtain an analytical signal response that is verified against the experimental response. Furthermore, we model the inhomogeneous mixture of randomly distributed aggregates and voids within a medium. We verify the practicality and reliability of our inhomogeneous models using experimental radar responses on an inhomogeneous medium.
ABSTRACT
This paper aims to investigate wave dispersion behavior in the quasi-solid state of concrete to better understand microstructure hydration interactions. The quasi-solid state refers to the consistency of the mixture between the initial liquid-solid stage and the hardened stage, where the concrete has not yet fully solidified but still exhibits viscous behavior. The study seeks to enable a more accurate evaluation of the optimal time for the quasi-liquid product of concrete using both contact and noncontact sensors, as current set time measurement approaches based on group velocity may not provide a comprehensive understanding of the hydration phenomenon. To achieve this goal, the wave dispersion behavior of P-wave and surface wave with transducers and sensors is studied. The dispersion behavior with different concrete mixtures and the phase velocity comparison of dispersion behavior are investigated. The analytical solutions are used to validate the measured data. The laboratory test specimen with w/c = 0.5 was subjected to an impulse in a frequency range of 40 kHz to 150 kHz. The results demonstrate that the P-wave results exhibit well-fitted waveform trends with analytical solutions, showing a maximum phase velocity when the impulse frequency is at 50 kHz. The surface wave phase velocity shows distinct patterns at different scanning times, which is attributed to the effect of the microstructure on the wave dispersion behavior. This investigation delivers profound knowledge of hydration and quality control in the quasi-solid state of concrete with wave dispersion behavior, providing a new approach for determining the optimal time of the quasi-liquid product. The criteria and methods developed in this paper can be applied to optimal timing for additive manufacturing of concrete material for 3D printers by utilizing sensors.
ABSTRACT
This study presents a developed ultrasonic water level detection (UWLD) system with an energy-efficient design and dual-target monitoring. The water level monitoring system with a non-contact sensor is one of the suitable methods since it is not directly exposed to water. In addition, a web-based monitoring system using a cloud computing platform is a well-known technique to provide real-time water level monitoring. However, the long-term stable operation of remotely communicating units is an issue for real-time water level monitoring. Therefore, this paper proposes a UWLD unit using a low-power consumption design for renewable energy harvesting (e.g., solar) by controlling the unit with dual microcontrollers (MCUs) to improve the energy efficiency of the system. In addition, dual targeting to the pavement and streamside is uniquely designed to monitor both the urban inundation and stream overflow. The real-time water level monitoring data obtained from the proposed UWLD system is analyzed with water level changing rate (WLCR) and water level index. The quantified WLCR and water level index with various sampling rates present a different sensitivity to heavy rain.
ABSTRACT
This letter presents an automated acoustic sensing device for rapid detection of delamination in concrete. The device consists of ball-chains for continual impact excitation and multi-channel microphones for acoustic sensing. A ball-chain is formed by multiple metal balls connected by flexible ropes and is dragged on concrete surface to excite vibration of delaminations. Compared to the conventional chain drag test, the ball-chain generates acoustic signals with higher signal-to-noise ratio (S/N) because the balls give isolated but continual impacts on concrete surface during dragging. The proposed method was validated on a concrete specimen with artificial delaminations.
ABSTRACT
We describe an approach that utilizes ultrasonic surface wave backscatter measurements to characterize the volume content of relatively small distributed defects (microcrack networks) in concrete. A simplified weak scattering model is used to demonstrate that the scattered wave field projected in the direction of the surface wave propagation is relatively insensitive to scatterers that are smaller than the propagating wavelength, while the scattered field projected in the opposite direction is more sensitive to sub-wavelength scatterers. Distributed microcracks in the concrete serve as the small scatterers that interact with a propagating surface wave. Data from a finite element simulation were used to demonstrate the viability of the proposed approach, and also to optimize a testing configuration to collect data. Simulations were validated through experimental measurements of ultrasonic backscattered surface waves from test samples of concrete constructed with different concentrations of fiber filler (0.0, 0.3 and 0.6%) to mimic increasing microcrack volume density and then samples with actual cracking induced by controlled thermal cycles. A surface wave was induced in the concrete samples by a 50kHz ultrasonic source operating 10mm above the surface at an angle of incidence of 9°. Silicon-based miniature MEMS acoustic sensors located a few millimeters above the concrete surface both behind and in front of the sender were used to detect leaky ultrasonic surface waves emanating from concrete. A normalized backscattered energy parameter was calculated from the signals. Statistically significant differences in the normalized backscattered energy were observed between concrete samples with varying levels of simulated and actual cracking damage volume.
ABSTRACT
UNLABELLED: The utility of micro-electro-mechanical sensors (MEMS) for application in air-coupled (contactless or noncontact) sensing to concrete nondestructive testing (NDT) is studied in this paper. The fundamental operation and characteristics of MEMS are first described. Then application of MEMS sensors toward established concrete test methods, including vibration resonance, impact-echo, ultrasonic surface wave, and multi-channel analysis of surface waves (MASW), is demonstrated. In each test application, the performance of MEMS is compared with conventional contactless and contact sensing technology. Favorable performance of the MEMS sensors demonstrates the potential of the technology for applied contactless NDT efforts. OBJECTIVE: To illustrate the utility of air-coupled MEMS sensors for concrete NDT, as compared with conventional sensor technology.
