Directly probing surfactant adsorption on nanoscopic trenches and pillars.

HYPOTHESIS: Confinement causes a change in the amount of surfactant adsorbed and in the adsorption morphology. EXPERIMENTS: Two cationic surfactants, tetradecyltrimethylammonium bromide (TTAB) and cetylpyridinium chloride (CPC) were adsorbed at the silica-water interface. Atomic force microscopy (AFM) force curves were measured on 50 nm and 80 nm wide trenches. Force curves were also measured on silica pillars, and the results were quantified based on distance from the edge. FINDINGS: Trenches: Adsorbed surfactants films in 50 nm and 80 nm trenches showed the same break-through values. However, compared to unconfined values, TTAB in trenches had decreased break-through and adhesion forces while CPC in trenches had increased break-through and adhesion forces, indicating that surfactant identity varies the confinement effect. Pillars: Near the edge, few surfactants adsorb, and those that do extend in the direction normal to the surface. While the experimental data agree qualitatively with previous coarse-grained molecular dynamic simulations, the length scales at which the phenomena are detected differ by ~ half-order of magnitude. Specifically, experimental data show measurable effects on adsorbed surfactant morphology at a distance from the edge 10-20 times the length of a surfactant molecule after accounting for the ~8 nm size of the probe.

Atomic Force Microscopy Force Mapping Analysis of an Adsorbed Surfactant above and below the Critical Micelle Concentration.

Force curves collected using an atomic force microscope (AFM) in the presence of adsorbed surfactants are often used to draw conclusions about adsorbed film packing, rigidity, and thickness. However, some noteworthy features of such force curve characteristics have yet to be thoroughly investigated and explained. In this work, we collected force curves from tetradecyltrimethylammonium bromide films adsorbed on highly oriented pyrolytic graphite (HOPG), silica, and silica that had been hydrophobized by functionalization with dichlorodimethyl silane. Breakthrough events in the force curves from several different trials were compared to show that the breakthrough distance, often reported as the adsorbed film thickness, increased with concentration below the critical micelle concentration (CMC) but was approximately 3.5 nm on all surfaces between 2× and 10× CMC; an unexpected result because of the different surface chemistries for the three surfaces. We employed an AFM probe with a different force constant ( k) value as well as a colloidal probe and the breakthrough distance remained approximately 3.5 nm in all cases. Gradient mapping, a variant of force mapping, was also implemented on the three surfaces and resulted in a new technique for visualizing adsorbed surfactant in situ. The resulting maps showed patches of adsorbed surfactant below the CMC and revealed that with increasing concentration, the size of the patches increased resulting in full coverage near and above the CMC. These results are, to our knowledge, the first time force mapping has been used to spatially track patches of adsorbed surfactant. Finally, layers of surfactants on an AFM tip were investigated by collecting a force map on a single AFM tip using the tip of a separate AFM probe. A breakthrough event was observed between the tips, indicating that a layer of surfactant was present on at least one, if not both tips.

Rational design of aromatic surfactants for graphene/natural rubber latex nanocomposites with enhanced electrical conductivity.

HYPOTHESIS: Graphene nanoplatelets (GNPs) can be dispersed in natural rubber matrices using surfactants. The stability and properties of these composites can be optimized by the choice of surfactants employed as stabilizers. Surfactants can be designed and synthesized to have enhanced compatibility with GNPs as compared to commercially available common surfactants. Including aromatic groups in the hydrophobic chain termini improves graphene compatibility of surfactants, which is expected to increase with the number of aromatic moieties per surfactant molecule. Hence, it is of interest to study the relationship between molecular structure, dispersion stability and electrical conductivity enhancement for single-, double-, and triple-chain anionic graphene-compatible surfactants. EXPERIMENTS: Graphene-philic surfactants, bearing two and three chains phenylated at their chain termini, were synthesized and characterized by proton nuclear magnetic resonance (1H NMR) spectroscopy. These were used to formulate and stabilize dispersion of GNPs in natural rubber latex matrices, and the properties of systems comprising the new phenyl-surfactants were compared with commercially available surfactants, sodium dodecylsulfate (SDS) and sodium dodecylbenzenesulfonate (SDBS). Raman spectroscopy, field emission scanning electron microscopy (FESEM), atomic force microscopy (AFM), and high-resolution transmission electron microscopy (HRTEM) were used to study structural properties of the materials. Electrical conductivity measurements and Zeta potential measurements were used to assess the relationships between surfactant architecture and nanocomposite properties. Small-angle neutron scattering (SANS) was used to study self-assembly structure of surfactants. FINDINGS: Of these different surfactants, the tri-chain aromatic surfactant TC3Ph3 (sodium 1,5-dioxo-1,5-bis(3-phenylpropoxy)-3-((3phenylpropoxy)carbonyl) pentane-2-sulfonate) was shown to be highly graphene-compatible (nanocomposite electrical conductivity = 2.22 × 10-5 S cm-1), demonstrating enhanced electrical conductivity over nine orders of magnitude higher than neat natural rubber-latex matrix (1.51 × 10-14 S cm-1). Varying the number of aromatic moieties in the surfactants appears to cause significant differences to the final properties of the nanocomposites.