Pyrolysis of Waste Tires: A Review.

Waste tires are known as "black pollution", which is difficult to degrade. The safe handling and recycling of waste tires have always been the focus of and difficulty for the global rubber industry. Pyrolysis can not only solve the problem of environmental pollution but also completely treat the waste tires and recover valuable pyrolysis products. This paper summarizes research progress on the pyrolysis of waste tires, including the pyrolysis mechanism; the important factors affecting the pyrolysis of waste tires (pyrolysis temperature and catalysts); and the composition, properties, and applications of the three kinds of pyrolysis products. The composition and yield of pyrolysis products can be regulated by pyrolysis temperature and catalysts, and pyrolysis products can be well used in many industrial occasions after different forms of post-treatment.

Effect of Wet Mixing on Properties of Radial-Orientation Basalt Fiber-Reinforced Rubber Compounds.

The effects of wet mixing and traditional mixing on the properties of radial-orientation basalt fiber-reinforced rubber products were studied through experiments. The results show that compared with traditional mixing, the basalt fibers under the wet mixing conditions can more effectively enhance the physical and mechanical properties of composites. The properties of the composites, such as carbon black dispersion, filler dispersion, rolling resistance and wet-sliding resistance, were the best after the latex and carbon black were premixed and then mixed by a mixer. Through extrusion experiments with the developed short-fiber radial-orientation die, it can be found that the fluidity of composites after extrusion is enhanced. Through analysis utilizing an electron microscope, it is shown that when the BFs added with KH550 (3-Aminopropyltriethoxysilane) were modified by KH560 ((3-Glycidyloxypropyl)trimethoxysilane), the interface layers of BF (basalt fiber)-KH560-NR and BF-KH550-NR were formed, which improves the adhesion between BFs and the rubber matrix. Qualitative characterization experiments on the orientation direction of the vulcanized composites were carried out through the experiments; that is, the qualitative characterization experiments on the segmented cutting and vulcanization of the composites in the radial direction showed that the short-fiber radial-orientation die could greatly improve the radial orientation degree of the short fibers in the radial direction. After adding KH560, the performance of the composites reinforced by the short fibers was improved to a certain extent compared with those without KH560. By adding DZ (N,N-Dicyclohexyl-2-benzothiazolsulfene amide) and CTP(cytidine triphosphate disodium) into the vulcanization system, the curing process of compounds in mixing and extrusion was delayed and the scorching resistance of short-fiber-reinforced composites was enhanced. Under the same conditions, the properties of the compounds after extrusion were greatly improved compared with those without extrusion.

Influence of the Synergistic Effect of Multi-Walled Carbon Nanotubes and Carbon Fibers in the Rubber Matrix on the Friction and Wear of Metals during the Mixing Process.

As a piece of high-intensity running equipment, the wear of an internal mixer determines the quality of rubber and its life. In general, the wear of an internal mixer is caused by the friction between the rubber and metal during the mixing process, and the most severe wear position is the end face of the equipment. In this paper, a mixture of multi-walled carbon nanotubes (MWCNTs) and carbon fibers (CFs) are added to rubber by mechanical compounding to obtain MWCNT/CF/carbon black (CB) composites. By investigating the synergistic mechanism of MWCNTs and CFs, we analyze the effect of the MWCNT/CF ratio on the frictional wear of metal on the end face of the internal mixer. At the microscopic level, MWCNTs and CFs form a spatial meshwork with CB particles through synergistic interactions. The CB particles can be adsorbed on the spatial meshwork to promote the dispersion of CB particles. In addition, the formation of oil film can be slowed down due to the spatial meshwork, which could hinder the spillage of aromatic oil. Meanwhile, the spatial meshwork serves as a physical isolation layer between the rubber and metal to reduce friction. Therefore, it dramatically impacts the dispersion degree of CB particles, the friction coefficient, the roughness of the surface, and the wear of metal. It shows that the synergistic effect of MWCNT/CF and CB particles is best when the CF content of the rubber matrix is 5 phr, showing the most stable spatial network structure, the best dispersion of CB particles, and minor wear on the end face of the internal mixer.

Research on Friction and Wear Properties of Rubber Composites by Adding Glass Fiber during Mixing.

GF/rubber composites have sound insulation characteristics, heat resistance, good corrosion resistance, and high mechanical strength. The compounding machine's long working hours will inevitably wear the metal on the end face of the compounding machine. The wear of the end face metal will increase the gap between the chamber and the end face, which will lead to material leakage, reduce the mixing effect, and eventually affect the performance of GF/rubber composites. To ensure the implementation of GF/rubber composites, it is necessary to study the frictional wear behavior of GF/rubber composites on metals. In this paper, the effect of blending rubber with different amounts of GF on the frictional wear of metal on the end face was analyzed from the perspective of the formulation process, and the ratio of corrosion wear and abrasive wear was calculated for the first time.

Effect of the Addition of Different Amounts of Aramid Fibers on Metal Friction and Wear during Mixing.

Studies show that the long-term operation of a rubber mixer results in wear at the end face of the mixer. End face wear increases the gap between the mixing chamber and the end face, resulting in leakage and a reduction in the mixing performance, affecting the final product's quality. Therefore, it is essential to investigate the wear of the metal face during the mixing process. The present study added aramid fibers to a rubber compound using a mechanical blender to obtain a composite material. Then, the influence of the aramid fibers on the metal friction and wear of the end face of the mixer was analyzed. This article introduces the concept of the wear ratio and explores the friction and wear of metals from the perspective of formulation technology for the first time. With the addition of aramid fibers, the proportion of abrasive wear of rubber on metal decreased, and the proportion of corrosive wear increased during the mixing process; however, when the addition of aramid fibers exceeded 3 phr, the balance of abrasive wear of rubber on metal increased and the proportion of corrosive wear decreased. It was found that aramid fibers have the property of friction reduction, which reduces the wear of the rubber blend on the metal. When the amount of aramid fibers added was 3 phr, the amount of abrasion of the rubber compound on the metal was the lowest.

The Effect of Different Dosages of TESPT on Metal Friction and Metal Wear in the Mixing Process.

Studies show that the dispersion of silica in the mixing process is an important factor affecting the wear of the mixing chamber. As the most important mixing equipment, the long operational life of the internal mixer will cause wear in the rotor and chamber of the internal mixer. This wear increases the gap between the rotor and chamber of the internal mixer, reduces the mixing performance, weakens the dispersion of packing, and adversely affects the quality of the rubber produced. Therefore, it is important to investigate the metal wear in the mixing process. This article examines the effect of the addition of different amounts of silane coupling agents on metal friction and wear during the mixing process. The silane coupling agent has two functions. The first is to make the surface of the silica hydrophobic, enabling it to combine the inorganic matrix of the silica with the organic matrix of the rubber; the second is to inhibit the aggregation of the silica in the rubber. In the present study, we examine (1) the influence of different formulations on the friction and wear of the metal in the mixing chamber from the perspective of formulation technology, and (2) the correlation between corrosion wear and abrasive wear. It is found that a rubber compound with 6 phr of TESPT has the lowest metal wear and that adding more TESPT does not affect the degree of metal wear. As the amount of TESPT increases, the proportion of abrasive wear decreases, while the proportion of corrosive wear increases, reaching a maximum of 20.7%. In our study we found that abrasive wear is the predominant wear mechanism of a rubber compound on metal. In contrast, the corrosive wear caused by high-temperature water vapor still occupies a large proportion of the total wear. Therefore, improving silica dispersion and reducing abrasive wear are extremely important methods to protect the mixing chamber. However, the corrosion of metals by high-temperature water vapor should also be considered when preparing for the mixing process.

Numerical Optimization Simulation of Synchronous Four-Wing Rotor.

The mixer is the most widely used batch mixing equipment in the rubber industry. The rotor is a core component and has a great impact on the mixing effect of the equipment. The current rotor structure design is done empirically, being tightly dependent on practical experience. This paper proposes a method for optimizing the rotor structure by using optimization algorithms combined with numerical simulation technology. Using MATLAB software, a parametric design program for synchronous rotors and a set of optimization programs for the particle swarm optimization (PSO) algorithm were written. The global distribution index was used as the fitness function to optimize the synchronous rotor configuration. A comparative analysis of the rotors before and after optimization shows that the optimization process is feasible, and the results are reliable. This provides new ideas for the design and development of mixer rotors.

Effect of Adding MoDTC on the Properties of Carbon Black Rubber and the Friction and Wear of Metal during Mixing Process.

The gap between the rotor and the mixer chamber wall is an important factor in determining filler dispersion in rubber compounds. The inner wall of a mixer will wear after working for a long time, which will cause poor filler dispersion and affect the quality of rubber products. In this study, MoDTC was added to carbon black as a kind of filler, and the effect on filler dispersion, the properties of the rubber product, and the friction and wear of rubber and metal in the mixing process were examined. Experimental data showed that after adding 3 phr of MoDTC, carbon black dispersion was greatly improved, the curing time was shortened, and the performance remained stable. It was also found that the Mo element of the compound with 3 phr MoDTC dispersed better than that of the other compounds. Most importantly, adding 3 phr of MoDTC greatly reduced the amount of wear on the metal during the mixing process. However, the opposite effect occurred when the MoDTC content was high. The method proposed in this study can not only improve filler dispersion in rubber but also reduce metal wear to prolong the service life of the mixing chamber when applied to an actual mixing process.