ABSTRACT
The feasibility of the extensive recycling of waste glass in alkali-activated materials (AAMs) was evaluated. The waste glass was utilised in AAMs for two purposes: a partial activator and a mineral precursor. The waste glass was blended with commercial sodium hydroxide and then heated to produce the solid activator powder. The technical performance of waste glass-based activator was investigated to replace commercial sodium silicate, a common alkali-activator used in AAMs. The effect of waste glass using only as the activator (WGA) and using as both activator and precursor (WGAP) in fly ash/slag-based one-part AAMs was studied using strength and microstructure characterisations. A mass-cost and emission analysis of waste glass-based AAMs (WGA and WGAP) was conducted, comparing the results with ordinary Portland cement (OPC). Characterisation tests of waste glass-based activator showed the effective formation of sodium silicate minerals with the adequate dissolution of activator in water by releasing reactive alkali and silica. Both WGA and WGAP showed comparable strengths at 56 days with a denser microstructure under ambient curing. According to mass analysis, waste glass could be utilised up to 17% by mass of total binder. Based on the analysis of cost and CO2 emissions, WGA and WGAP are around 23% and 15% cheaper and 84% and 82% greener than OPC. The dual role of waste glass in AAMs as an activator and as a precursor broadens the recycling of glass waste in the cement industry by favouring technical and environmental outcomes.
Subject(s)
Alkalies , Construction Materials , Coal Ash , Glass , RecyclingABSTRACT
The particle morphology and fabric of a granular soil influence its mechanical behavior. This study focuses on the evolution of the particle-level fabric and morphology of a uniformly graded sand sample subjected to one-dimensional compression up to 64 MPa. The microstructural changes with increased stresses were captured using in situ high-resolution X-ray computed tomography (X-ray CT) imaging. The processed images of particles were separated using the Monash Particle Separation Method (MPSM) for subsequent fabric and morphological analyses. The variations of various fabric parameters were studied using the separated particle volumes. New methods of assessing the morphology and crushability of particles were introduced including a comprehensive algorithm for determining coordination number, branch and contact normal vectors. Results of all fabric parameters were analyzed and discussed with reference to observed changes. Potential mechanisms were identified and relevant correlations were developed where warranted.
ABSTRACT
An accurate determination of particle-level fabric of granular soils from tomography data requires a maximum correct separation of particles. The popular marker-controlled watershed separation method is widely used to separate particles. However, the watershed method alone is not capable of producing the maximum separation of particles when subjected to boundary stresses leading to crushing of particles. In this paper, a new separation method, named as Monash Particle Separation Method (MPSM), has been introduced. The new method automatically determines the optimal contrast coefficient based on cluster evaluation framework to produce the maximum accurate separation outcomes. Finally, the particles which could not be separated by the optimal contrast coefficient were separated by integrating cuboid markers generated from the clustering by Gaussian mixture models into the routine watershed method. The MPSM was validated on a uniformly graded sand volume subjected to one-dimensional compression loading up to 32 MPa. It was demonstrated that the MPSM is capable of producing the best possible separation of particles required for the fabric analysis.
ABSTRACT
Improvements of soft soils by mechanically mixing cementitious additives have been widely practised for construction of infrastructure. Mixing of additives improves strength and compressibility properties of soils through the development of soil structure. This study investigates the 1-D compression behaviour of alkali-activated slag treated acid sulphate soils (ASS) cured up to 365 days. The void ratio-logarithm of pressure (e-logσ') behaviour of treated ASS, including the destructuration behaviour, with additive contents and curing time have been analysed. X-ray diffraction (XRD) and scanning electron microscopy (SEM) analyses have been undertaken to explain the observed variations of the 1-D compression behaviour. This paper presents the results of these analyses in view of obtaining an insight into the 1-D compression behaviour of treated ASS with the help of mineralogical analysis.
ABSTRACT
This paper presents the results of X-ray CT imaging of the microstructure of sand particles subjected to high pressure one-dimensional compression leading to particle crushing. A high resolution X-ray CT machine capable of in situ imaging was employed to capture images of the whole volume of a sand sample subjected to compressive stresses up to 79.3 MPa. Images of the whole sample obtained at different load stages were analysed using a commercial image processing software (Avizo) to reveal various microstructural properties, such as pore and particle volume distributions, spatial distribution of void ratios, relative breakage, and anisotropy of particles.
