The influence of copper-doped mesoporous bioactive nanospheres on the temperature rise during polymerization, polymer cross-linking density, monomer release and embryotoxicity of dental composites.

OBJECTIVES: Composites with copper-doped mesoporous bioactive nanospheres (Cu-MBGN) were developed to prevent secondary caries by imparting antimicrobial and ion-releasing/remineralizing properties. METHODS: Seven experimental composites containing 1, 5 or 10 wt% Cu-MBGN, the corresponding inert controls (silica) and bioactive controls (bioactive glass 45S5) were prepared. The temperature rise during light curing, cross-linking density by ethanol softening test, monomer elution and their potential adverse effects on the early development of zebrafish Danio rerio was investigated. RESULTS: Materials combining Cu-MBGN and silica showed the highest resistance to ethanol softening, as did the bioactive controls. Cu-MBGN composites showed significant temperature rise and reached maximum temperature in the shortest time. Bisphenol A was not detected, while bis-GMA was found only in the control materials and TEGDMA in the eluates of all materials. There was no increase in zebrafish mortality and abnormality rates during exposure to the eluates of any of the materials. CONCLUSIONS: The composite with 5 wt% Cu-MBGN combined with nanosilica fillers showed the lowest ethanol softening, indicating the polymer's highest durability and cross-linking density. Despite the TEGDMA released from all tested materials, no embryotoxic effect was observed.

Multiple choice as formative assessment in dental education.

INTRODUCTION: The effectiveness of multiple-choice questions (MCQs) in dental education is pivotal to student performance and knowledge advancement. However, their optimal implementation requires exploration to enhance the benefits. MATERIALS AND METHODS: An educational tool incorporating MCQs was administered from the 5th to the 10th semester in a dental curriculum. The students filled out a questionnaire after the MCQ, which was linked to the learning management system. Four cohorts of four semesters generated 2300 data points analysed by Spearmen correlation and mixed model regression analysis. RESULTS: Demonstrated a significant correlation between early exam preparation and improved student performance. Independent study hours and lecture attendance emerged as significant predictors, accounting for approximately 10.27% of the variance in student performance on MCQs. While the number of MCQs taken showed an inverse relationship with study hours, the perceived clarity of these questions positively correlated with academic achievement. CONCLUSION: MCQs have proven effective in enhancing student learning and knowledge within the discipline. Our analysis underscores the important role of independent study and consistent lecture attendance in positively influencing MCQ scores. The study provides valuable insights into using MCQs as a practical tool for dental student learning. Moreover, the clarity of assessment tools, such as MCQs, remains pivotal in influencing student outcomes. This study underscores the multifaceted nature of learning experiences in dental education and the importance of bridging the gap between student expectations and actual performance.

Towards bone regeneration: Understanding the nucleating ability of proline-rich peptides in biomineralisation.

Obtaining rapid mineralisation is a challenge in current bone graft materials, which has been attributed to the difficulty of guiding the biological processes towards osteogenesis. Amelogenin, a key protein in enamel formation, inspired the design of two intrinsically disordered peptides (P2 and P6) that enhance in vivo bone formation, but the process is not fully understood. In this study, we have elucidated the mechanism by which these peptides induce improved mineralisation. Our molecular dynamics analysis demonstrated that in an aqueous environment, P2 and P6 fold to interact with the surrounding Ca2+, PO43- and OH- ions, which can lead to apatite nucleation. Although P2 has a less stable backbone, it folds to a stable structure that allows for the nucleation of larger calcium phosphate aggregates than P6. These results were validated experimentally in a concentrated simulated body fluid solution, where the peptide solutions accelerated the mineralisation process compared to the control and yielded mineral structures mimicking the amorphous calcium phosphate crystals that can be found in lamella bone. A pH drop for the peptide groups suggests depletion of calcium and phosphate, a prerequisite for intrinsic osteoinduction, while S/TEM and SEM suggested that the peptide regulated the mineral nucleation into lamella flakes. Evidently, the peptides accelerate and guide mineral formation, elucidating the mechanism for how these peptides can improve the efficacy of P2 or P6 containing devices for bone regeneration. The work also demonstrates how experimental mineralisation study coupled with molecular dynamics is a valid method for understanding and predicting in vivo performance prior to animal trials.

A Comparative Investigation of Chemical Decontamination Methods for In-Situ Cleaning of Dental Implant Surfaces.

Surface chemistry evaluation is crucial in assessing the efficacy of chemical decontamination products for titanium implants. This study aimed to investigate the effectiveness of chemical decontamination solutions in cleaning a contaminated dental implant surface and to evaluate the potential of combining Pluronic gel with hydrogen peroxide (NuBone®Clean) by evaluating pellicle disruption and re-formation on implant surfaces. In addition, ensuring safety with in vitro and human testing protocols. X-ray Photoelectron Spectroscopy (XPS) was utilised for surface analysis. All the tested gels had some effect on the surface cleanness except for PrefGel®. Among the tested chemical decontamination candidates, NuBone®Clean demonstrated effectiveness in providing a cleaner titanium surface. Furthermore, none of the tested chemical agents exhibited cytotoxic effects, and the safety assessment showed no adverse events. The results of this study highlight the significance of conducting comprehensive evaluations, encompassing safety and efficacy, before introducing new chemical agents for dental treatments. The findings suggest that NuBone®Clean shows potential as a chemical decontamination solution for implant surfaces. However, further investigation through randomised clinical trials is necessary. By adhering to rigorous testing protocols, the development of safe and efficient chemical decontamination strategies can be advanced, benefiting patients and promoting progress in implant dentistry.

Regenerative Endodontics by Cell Homing: A Review of Recent Clinical trials.

INTRODUCTION: The conventional treatment for irreversibly inflamed or necrotic teeth is root canal treatment or apexification. Regenerative endodontics aims to regenerate the damaged "pulp-like" tissue, which can preserve the teeth' vitality and sensitivity while avoiding necrosis. The main clinical benefit is root maturation. The "pulp-like" tissue does not refer to regenerated pulp tissue with an odontoblastic layer or the formation of pulp-dentin complexes. The cell homing technique is built on endogenous stem cells and their capacity to regenerate tissue. Cell homing refers to endogenous cells' migration or infiltration into the cite when stimulated by physiochemical or biological stimuli or by passive flow with a blood clot from the apical tissue. Its Regenerative Endodontic Procedures success criteria are defined by the American Association of Endodontists. The purpose of this article is to provide an overview of vital pulp tissue and various strategies to promote regeneration of damaged pulp tissue. The cell homing technique will be reviewed through clinical trials. METHODS: We performed a comprehensive literature review on a total of nine clinical trials of regenerative endodontics using the cell-homing technique based on three databases and duplicate manuscripts were removed. RESULTS: Regenerative endodontics using the cell-homing technique shows promising results that can be translated into clinical practice. However, a favorable result was observed in immature teeth, and the results are contradictory in mature teeth. CONCLUSION: Regeneration therapy is an attractive new alternative to conventional endodontic treatments. Preservation of vitality and continuation of root development in damaged teeth would be a clear advantage.

Using Copper-Doped Mesoporous Bioactive Glass Nanospheres to Impart Anti-Bacterial Properties to Dental Composites.

Experimental dental resin composites containing copper-doped mesoporous bioactive glass nanospheres (Cu-MBGN) were developed to impart anti-bacterial properties. Increasing amounts of Cu-MBGN (0, 1, 5 and 10 wt%) were added to the BisGMA/TEGDMA resin matrix containing micro- and nano-fillers of inert glass, keeping the resin/filler ratio constant. Surface micromorphology and elemental analysis were performed to evaluate the homogeneous distribution of filler particles. The study investigated the effects of Cu-MBGN on the degree of conversion, polymerization shrinkage, porosity, ion release and anti-bacterial activity on S. mutans and A. naeslundii. Experimental materials containing Cu-MBGN showed a dose-dependent Cu release with an initial burst and a further increase after 28 days. The composite containing 10% Cu-MBGN had the best anti-bacterial effect on S. mutans, as evidenced by the lowest adherence of free-floating bacteria and biofilm formation. In contrast, the 45S5-containing materials had the highest S. mutans adherence. Ca release was highest in the bioactive control containing 15% 45S5, which correlated with the highest number of open porosities on the surface. Polymerization shrinkage was similar for all tested materials, ranging from 3.8 to 4.2%, while the degree of conversion was lower for Cu-MBGN materials. Cu-MBGN composites showed better anti-bacterial properties than composites with 45S5 BG.

Solution blow spinning of highly deacetylated chitosan nanofiber scaffolds for dermal wound healing.

Biocompatible fibrous scaffolds based on highly deacetylated chitosan were fabricated using high-throughput solution blow spinning. Scanning electron microscopy analysis revealed that the chitosan nanofiber scaffolds had ultrafine and continuous fibers (300-1200 nm) with highly interconnected porous structures (30-75% porosity), mimicking some aspects of the native extracellular matrix in skin tissue. Post-treatment of as-spun nanofibers with aqueous potassium carbonate solution resulted in a fibrous scaffold with a high chitosan content that retained its fibrous structural integrity for cell culture. Analysis of the mechanical properties of the chitosan nanofiber scaffolds in both dry and wet conditions showed that their strength and durability were sufficient for wound dressing applications. Significantly, the wet scaffold underwent remarkable elastic deformation during stretch such that the elongation at break dramatically increased to up to 44% of its original length, showing wavy fiber morphology near the break site. The culture of normal human dermal fibroblast cells onto scaffolds for 1-14 days demonstrated that the scaffolds were highly compatible and a suitable platform for cell adhesion, viability, and proliferation. Secretion profiles of wound healing-related proteins to the cell culture medium demonstrated that chitosan fibers were a promising scaffold for wound healing applications. Overall, the dense fibrous network with high porosity of the chitosan nanofiber scaffold and their mechanical properties indicate that they could be used to design and fabricate new materials that mimic the epidermis layer of natural skin.

The Antibacterial and Cytotoxic Effects of Silver Nanoparticles Coated Titanium Implants: A Narrative Review.

Nanotechnology has become an emerging research field with numerous biomedical scientific applications. Silver possesses bactericidal activities that have been harnessed for centuries; however, there is a concern about the toxic effects of silver nanoparticles. This paper aims to provide an overview of silver-treated dental implants and discuss their potential to reduce the prevalence of peri-implant diseases. An electronic search was performed using PubMed. After screening, data extraction was performed on the 45 remaining articles using inclusion and exclusion criteria. Most of the articles demonstrated that silver nanoparticles embedded in a coating layer and/or on surface-treated titanium exhibit sound antibacterial effects and biocompatibility. Most of the reviewed studies revealed that silver nanoparticles on dental implant surfaces reduced cytotoxicity but provided a prolonged antibacterial effect. The cytotoxicity and antibacterial effect are closely linked to how the silver nanoparticles are released from the titanium surfaces, where a slower release increases cell viability and proliferation. However, to improve the clinical translation, there is still a need for more studies, especially evaluating the long-term systemic effects and studies recreating the conditions in the oral cavity.

Impact of Copper-Doped Mesoporous Bioactive Glass Nanospheres on the Polymerisation Kinetics and Shrinkage Stress of Dental Resin Composites.

We embedded copper-doped mesoporous bioactive glass nanospheres (Cu-MBGN) with antibacterial and ion-releasing properties into experimental dental composites and investigated the effect of Cu-MBGN on the polymerisation properties. We prepared seven composites with a BisGMA/TEGDMA (60/40) matrix and 65 wt.% total filler content, added Cu-MBGN or a combination of Cu-MBGN and silanised silica to the silanised barium glass base, and examined nine parameters: light transmittance, degree of conversion (DC), maximum polymerisation rate (Rmax), time to reach Rmax, linear shrinkage, shrinkage stress (PSS), maximum PSS rate, time to reach maximum PSS rate, and depth of cure. Cu-MBGN without silica accelerated polymerisation, reduced light transmission, and had the highest DC (58.8 ± 0.9%) and Rmax (9.8 ± 0.2%/s), but lower shrinkage (3 ± 0.05%) and similar PSS (0.89 ± 0.07 MPa) versus the inert reference (0.83 ± 0.13 MPa). Combined Cu-MBGN and silica slowed the Rmax and achieved a similar DC but resulted in higher shrinkage. However, using a combined 5 wt.% Cu-MBGN and silica, the PSS resembled that of the inert reference. The synergistic action of 5 wt.% Cu-MBGN and silanised silica in combination with silanised barium glass resulted in a material with the highest likelihood for dental applications in future.

Is There a Better Biomaterial for Dental Implants than Titanium?-A Review and Meta-Study Analysis.

This article focuses on preclinical studies and reviews the available evidence from the literature on dental implant and abutment materials in the last decade. Specifically, different peri-implantitis materials and how surface modifications may affect the peri-implant soft-tissue seal and subsequently delay or hinder peri-implantitis are examined. This review analyzed more than 30 studies that were Randomized Controlled Trials (RCTs), Controlled Clinical Trials (CCTs), or prospective case series (CS) with at least six months of follow-up. Meta-analyses were performed to make a comparison between different implant materials (titanium vs. zirconia), including impact on bone changes, probing depth, plaque levels, and peri-implant mucosal inflammation, as well as how the properties of the implant material and surface modifications would affect the peri-implant soft-tissue seal and peri-implant health conditions. However, there was no clear evidence regarding whether titanium is better than other implant materials. Clinical evidence suggests no difference between different implant materials in peri-implant bone stability. The metal analysis offered a statistically significant advantage of zirconia implants over titanium regarding developing a favorable response to the alveolar bone.

Design and clinical application of injectable hydrogels for musculoskeletal therapy.

Musculoskeletal defects are an enormous healthcare burden and source of pain and disability for individuals. With an aging population, the proportion of individuals living with these medical indications will increase. Simultaneously, there is pressure on healthcare providers to source efficient solutions, which are cheaper and less invasive than conventional technology. This has led to an increased research focus on hydrogels as highly biocompatible biomaterials that can be delivered through minimally invasive procedures. This review will discuss how hydrogels can be designed for clinical translation, particularly in the context of the new European Medical Device Regulation (MDR). We will then do a deep dive into the clinically used hydrogel solutions that have been commercially approved or have undergone clinical trials in Europe or the United States. We will discuss the therapeutic mechanism and limitations of these products. Due to the vast application areas of hydrogels, this work focuses only on treatments of cartilage, bone, and the nucleus pulposus. Lastly, the main steps toward clinical translation of hydrogels as medical devices are outlined. We suggest a framework for how academics can assist small and medium MedTech enterprises conducting the initial clinical investigation and post-market clinical follow-up required in the MDR. It is evident that the successful translation of hydrogels is governed by acquiring high-quality pre-clinical and clinical data confirming the device mechanism of action and safety.

Bioengineered Hierarchical Bonelike Compartmentalized Microconstructs Using Nanogrooved Microdiscs.

Fabrication of vascularized large-scale constructs for regenerative medicine remains elusive since most strategies rely solely on cell self-organization or overly control cell positioning, failing to address nutrient diffusion limitations. We propose a modular and hierarchical tissue-engineering strategy to produce bonelike tissues carrying signals to promote prevascularization. In these 3D systems, disc-shaped microcarriers featuring nanogrooved topographical cues guide cell behavior by harnessing mechanotransduction mechanisms. A sequential seeding strategy of adipose-derived stromal cells and endothelial cells is implemented within compartmentalized, liquefied-core macrocapsules in a self-organizing and dynamic system. Importantly, our system autonomously promotes osteogenesis and construct's mineralization while promoting a favorable environment for prevascular-like endothelial organization. Given its modular and self-organizing nature, our strategy may be applied for the fabrication of larger constructs with a highly controlled starting point to be used for local regeneration upon implantation or as drug-screening platforms.

Reconstructing topography and extent of injury to the superior mesenteric artery plexus in right colectomy with extended D3 mesenterectomy: a composite multimodal 3-dimensional analysis.

BACKGROUND: Superior mesenteric artery plexus (SMAP) injury is reported to cause postoperative intractable diarrhea after pancreatic/colonic surgery with extended lymphadenectomy. This study aims to describe the SMAP microanatomy and extent of injury after right colectomy with extended D3 mesenterectomy for cancer. METHODS: Three groups (I) anatomical dissection, (II) postmortem histology, and (III) surgical specimen histology were included. Nerve count and area were compared between groups II and III and paravascular sheath thickness between groups I and II. 3D models were generated through 3D histology, nanoCT scanning, and finally through 3D printing. RESULTS: A total of 21 specimens were included as follows: Group (I): 5 (3 females, 80-93 years), the SMAP is a complex mesh surrounding the superior mesenteric artery (SMA), branching out, following peripheral arteries and intertwining between them, (II): 7 (5 females, 71-86 years), nerve count: 53 ± 12.42 (38-68), and area: 1.84 ± 0.50 mm2 (1.16-2.29), and (III): 9 (5 females, 55-69 years), nerve count: 31.6 ± 6.74 (range 23-43), and area: 0.889 ± 0.45 mm2 (range 0.479-1.668). SMAP transection injury is 59% of nerve count and 48% of nerve area at middle colic artery origin level. The median values of paravascular sheath thickness decreased caudally from 2.05 to 1.04 mm (anatomical dissection) and from 2.65 to 1.17 mm (postmortem histology). 3D histology models present nerve fibers exclusively within the paravascular sheath, and lymph nodes were observed only outside. NanoCT-derived models reveal oblique nerve fiber trajectories with inclinations between 35° and 55°. Two 3D-printed models of the SMAP were also achieved in a 1:2 scale. CONCLUSION: SMAP surrounds the SMA and branches within the paravascular sheath, while bowel lymph nodes and vessels lie outside. Extent of SMAP injury on histological slides (transection only) was 48% nerve area and 59% nerve count. The 35°-55° inclination range of SMAP nerves possibly imply an even larger injury when plexus excision is performed (lymphadenectomy). Reasons for later improvement of bowel function in these patients can lie in the interarterial nerve fibers between SMA branches.

Recent Developments in Chitosan-Based Micro/Nanofibers for Sustainable Food Packaging, Smart Textiles, Cosmeceuticals, and Biomedical Applications.

Chitosan has many useful intrinsic properties (e.g., non-toxicity, antibacterial properties, and biodegradability) and can be processed into high-surface-area nanofiber constructs for a broad range of sustainable research and commercial applications. These nanofibers can be further functionalized with bioactive agents. In the food industry, for example, edible films can be formed from chitosan-based composite fibers filled with nanoparticles, exhibiting excellent antioxidant and antimicrobial properties for a variety of products. Processing 'pure' chitosan into nanofibers can be challenging due to its cationic nature and high crystallinity; therefore, chitosan is often modified or blended with other materials to improve its processability and tailor its performance to specific needs. Chitosan can be blended with a variety of natural and synthetic polymers and processed into fibers while maintaining many of its intrinsic properties that are important for textile, cosmeceutical, and biomedical applications. The abundance of amine groups in the chemical structure of chitosan allows for facile modification (e.g., into soluble derivatives) and the binding of negatively charged domains. In particular, high-surface-area chitosan nanofibers are effective in binding negatively charged biomolecules. Recent developments of chitosan-based nanofibers with biological activities for various applications in biomedical, food packaging, and textiles are discussed herein.

Incorporation of Copper-Doped Mesoporous Bioactive Glass Nanospheres in Experimental Dental Composites: Chemical and Mechanical Characterization.

Experimental dental resin composites incorporating copper-doped mesoporous bioactive glass nanospheres (Cu-MBGN) were designed to impart antibacterial and remineralizing properties. The study evaluated the influence of Cu-MBGN on the mechanical properties and photopolymerization of resin composites. Cu-MBGN were synthesized using a microemulsion-assisted sol-gel method. Increasing amounts of Cu-MBGN (0, 1, 5, and 10 wt %) were added to the organic polymer matrix with inert glass micro- and nanofillers while maintaining a constant resin/filler ratio. Six tests were performed: X-ray diffraction, scanning electron microscopy, flexural strength (FS), flexural modulus (FM), Vickers microhardness (MH), and degree of conversion (DC). FS and MH of Cu-MBGN composites with silica fillers showed no deterioration with aging, with statistically similar results at 1 and 28 days. FM was not influenced by the addition of Cu-MBGN but was reduced for all tested materials after 28 days. The specimens with 1 and 5% Cu-MBGN had the highest FS, FM, MH, and DC values at 28 days, while controls with 45S5 bioactive glass had the lowest FM, FS, and MH. DC was high for all materials (83.7-93.0%). Cu-MBGN composites with silica have a potential for clinical implementation due to high DC and good mechanical properties with adequate resistance to aging.

In vitro biological response of human osteoblasts in 3D chitosan sponges with controlled degree of deacetylation and molecular weight.

We have studied the effect of chitosan sponges, produced from chitosan batches with distinct degree of deacetylation (DDA) and molecular weight (Mw), on the adhesion, growth and differentiation of primary human osteoblasts with an aim to offer a suitable tool for guided bone regeneration. All the chitosan sponges revealed similar microstructure, irrespective of the DDA (58, 73, 82, 88, and 91 %) and Mw (749, 547, 263, 215, and 170 kDa, respectively). Cell spreading was higher on sponges having a higher DDA. Higher DDA induced a more pronounced increase in alkaline phosphatase activity, osteopontin (OPN), vascular endothelial growth factor-A (VEGF), interleukin-6 (IL-6), and reduction in monocyte chemoattractant protein-1 (MCP-1), sclerostin (SOST) and dickkopf related protein-1 as compared to lower DDA. Lower DDA induced the increased secretion of osteoprotegerin and SOST as compared to higher DDA. The combination of higher DDA and Mw induced an increased secretion of VEGF and IL-6, however reduced the secretion of OPN as compared to chitosan with similar DDA but with lower Mw. In summary, the variations in cellular responses to the different chitosan sponges indicate a potential for individual tailoring of desired responses in guided bone regeneration.

Adhesion of Escherichia Coli to Nanostructured Surfaces and the Role of Type 1 Fimbriae.

Bacterial fimbriae are an important virulence factor mediating adhesion to both biotic and abiotic surfaces and facilitating biofilm formation. The expression of type 1 fimbriae of Escherichia coli is a key virulence factor for urinary tract infections and catheter-associated urinary tract infections, which represent the most common nosocomial infections. New strategies to reduce adhesion of bacteria to surfaces is therefore warranted. The aim of the present study was to investigate how surfaces with different nanotopography-influenced fimbriae-mediated adhesion. Surfaces with three different nanopattern surface coverages made in polycarbonate were fabricated by injection molding from electron beam lithography nanopatterned templates. The surfaces were constructed with features of approximately 40 nm width and 25 nm height with 100 nm, 250 nm, and 500 nm interspace distance, respectively. The role of fimbriae type 1-mediated adhesion was investigated using the E. coli wild type BW25113 and ΔfimA (with a knockout of major pilus protein FimA) and ΔfimH (with a knockout of minor protein FimH) mutants. For the surfaces with nanotopography, all strains adhered least to areas with the largest interpillar distance (500 nm). For the E. coli wild type, no difference in adhesion between surfaces without pillars and the largest interpillar distance was observed. For the deletion mutants, increased adhesion was observed for surfaces without pillars compared to surfaces with the largest interpillar distance. The presence of a fully functional type 1 fimbria decreased the bacterial adhesion to the nanopatterned surfaces in comparison to the mutants.

Structural and Chemical Hierarchy in Hydroxyapatite Coatings.

Hydroxyapatite coatings need similarly shaped splats as building blocks and then a homogeneous microstructure to unravel the structural and chemical hierarchy for more refined improvements to implant surfaces. Coatings were thermally sprayed with differently sized powders (20-40, 40-63 and 63-80 µm) to produce flattened homogeneous splats. The surface was characterized for splat shape by profilometry and Atomic force microscopy (AFM), crystal size by AFM, crystal orientation by X-ray diffraction (XRD) and structural variations by XRD. Chemical composition was assessed by phase analysis, but variations in chemistry were detected by XRD and Raman spectroscopy. The resulting surface electrical potential was measured by Kelvin probe AFM. Five levels of structural hierarchy were suggested: the coating, the splat, oriented crystals, alternate layers of oxyapatite and hydroxyapatite (HAp) and the suggested anion orientation. Chemical hierarchy was present over a lower range of order for smaller splats. Coatings made from smaller splats exhibited a greater electrical potential, inferred to arise from oxyapatite, and supplemented by ordered OH- ions in a rehydroxylated surface layer. A model has been proposed to show the influence of structural hierarchy on the electrical surface potential. Structural hierarchy is proposed as a means to further refine the properties of implant surfaces.

Nano-CT as tool for characterization of dental resin composites.

Technological advances have made it possible to examine dental resin composites using 3D nanometer resolution. This investigation aims to characterize existing dental nano-hybrid and micro-hybrid resin composites through comparing and contrasting nano-computed tomography (nano-CT) with micro-CT and high-resolution SEM images. Eight commercially available and widely used dental resin composites, 2 micro-hybrid and 6 nano-hybrid were researched. Cured samples were examined and characterized using nano-CT (resolution 450 nm) and compared with micro-CT images (resolution 2 µm). Acquired images were reconstructed and image analysis was carried out to determine porosity and pore morphology. A comprehensive comparison of scanning micrograph images unsurprisingly revealed that the nano-CT images displayed greater detail of the ultrastructure of cured dental resin composites. Filler particle diameters and its volumes were lower when measured using nano-CT, porosity being higher where analysed at higher resolution. There were large variations between the examined materials. Fewer voids were found in Tetric EvoCeram and IPS Empress Direct, the smallest pores being found in Universal XTE and Tetric EvoCeram. Nano-CT was successfully used to investigate the morphology of dental resin composites and showed that micro-CT gives a lower porosity and pore size but overestimates filler particle size. There were large discrepancies between the tested composites. Evidence of porosities and pores within a specimen is a critical finding and it might have a detrimental effect on a material's clinical performance.