Low Conductive Electrodeposited Poly(2,5-dimethoxyaniline) as a Key Material in a Double Lateral Heterojunction, for Sub-ppm Ammonia Sensing in Humid Atmosphere.

We present a new device called a double lateral heterojunction (DLH) as an ammonia sensor in humid atmosphere. It combines polyaniline derivatives in their poor conducting state with a highly conductive molecular material, lutetium bisphthalocyanine, LuPc2. Polyaniline and poly(2,5-dimethoxyaniline) are electrodeposited on ITO interdigitated electrodes, leading to an original device that can be obtained only by electrochemistry and not by other solution processing techniques. Both polymers lead to highly conducting materials that require a neutralization step before their coverage by LuPc2. While the device based on polyaniline shows ohmic behavior, the nonlinear I- V characteristics of the poly(2,5-dimethoxyaniline)-based DLH prove the existence of energy barriers at the interfaces, as demonstrated by impedance spectroscopy. It exhibits a particularly interesting sensitivity to ammonia, at room temperature and in a broad relative humidity range. Thanks to its higher energy barriers, the poly(2,5-dimethoxyaniline)/LuPc2 DLH is the most sensitive device with a limit of detection of 320 ppb. This work paves the way for the use of substituted polyanilines in conductometric sensors not only in the field of air quality monitoring but also in the field of health diagnosis by measurement in human breath.

Comprehensive Study of Poly(2,3,5,6-tetrafluoroaniline): From Electrosynthesis to Heterojunctions and Ammonia Sensing.

In this work, we report for the first time on a comprehensive study of poly(2,3,5,6-tetrafluoroaniline) (PTFANI). Contrary to the nonfluorinated polyaniline (PANI) or its analogues bearing one fluorine atom, PTFANI is a poorly conductive material. We present a comprehensive study of the electrosynthesized PTFANI from its monomer in an acidic aqueous medium. PTFANI was fully characterized by a potential-pH diagram, spectroelectrochemistry, and electrochemical quartz crystal microbalance (EQCM) measurements, as well as by a morphological study. Combined with the X-ray photoelectron spectroscopy (XPS) analysis, it allowed us to understand the redox properties of this polymer compared to those of the unsubstituted PANI. At pH < 1.85, no proton transfer occurred during the electrochemical process, but the insertion of anions at the site of the protonated imines was demonstrated through the EQCM and XPS experiments. PTFANI showed a lower ratio of 1 ClO4- per 3 2,3,5,6-tetrafluoroaniline units compared to that of PANI. The behavior at pH > 1.85 was different; no anion upload was observed during the electron transfer, but 1 H+ per electron was involved during the transition between the leucoemeraldine and emeraldine base forms. It should also be noted that the oxidation of the emeraldine into the pernigraniline form was not accessible in PTFANI because of the electron-withdrawing effects of the fluorine atoms. However, we took advantage of the unique behavior of PTFANI to build heterojunctions, by combining with a highly conductive molecular material, namely lutetium bisphthalocyanine, LuPc2. The obtained double-lateral heterojunction exhibited a particularly interesting sensitivity to ammonia, even under humid atmospheres, with a limit of detection of 450 ppb. This work paves the way for the use of PTFANI in other electronic devices and as a sensor not only in the field of air quality monitoring but also in the field of health diagnosis in measuring the human breath.

High-resolution characterization of the diffusion of light chemical elements in metallic components by scanning microwave microscopy.

An original sub-surface, high spatial resolution tomographic technique based on scanning microwave microscopy (SMM) is used to visualize in-depth materials with different chemical compositions. A significant phase difference in SMM between aluminum and chromium buried patterns has been observed. Moreover this technique was used to characterize a solid solution of a light chemical element (oxygen) in a metal lattice (zirconium). The large solubility of the oxygen in zirconium leads to modifications of the properties of the solid solution that can be measured by the phase shift signal in the SMM technique. The signal obtained in cross-section of an oxidized Zr sample shows the excellent agreement between phase shift profiles measured at different depths. Such a profile can reveal the length of diffusion of the oxygen in zirconium under the surface. The comparison with the oxygen concentration measured by nuclear reaction analysis shows excellent agreement in terms of length of diffusion and spatial distribution of the oxygen. A rapid calibration shows a linear dependence between the phase shift and the oxygen concentration. The SMM method opens up new possibilities for indirect measurements of the oxygen concentration dissolved in the metal lattice.

The skeleton of the staghorn coral Acropora millepora: molecular and structural characterization.

The scleractinian coral Acropora millepora is one of the most studied species from the Great Barrier Reef. This species has been used to understand evolutionary, immune and developmental processes in cnidarians. It has also been subject of several ecological studies in order to elucidate reef responses to environmental changes such as temperature rise and ocean acidification (OA). In these contexts, several nucleic acid resources were made available. When combined to a recent proteomic analysis of the coral skeletal organic matrix (SOM), they enabled the identification of several skeletal matrix proteins, making A. millepora into an emerging model for biomineralization studies. Here we describe the skeletal microstructure of A. millepora skeleton, together with a functional and biochemical characterization of its occluded SOM that focuses on the protein and saccharidic moieties. The skeletal matrix proteins show a large range of isoelectric points, compositional patterns and signatures. Besides secreted proteins, there are a significant number of proteins with membrane attachment sites such as transmembrane domains and GPI anchors as well as proteins with integrin binding sites. These features show that the skeletal proteins must have strong adhesion properties in order to function in the calcifying space. Moreover this data suggest a molecular connection between the calcifying epithelium and the skeletal tissue during biocalcification. In terms of sugar moieties, the enrichment of the SOM in arabinose is striking, and the monosaccharide composition exhibits the same signature as that of mucus of acroporid corals. Finally, we observe that the interaction of the acetic acid soluble SOM on the morphology of in vitro grown CaCO3 crystals is very pronounced when compared with the calcifying matrices of some mollusks. In light of these results, we wish to commend Acropora millepora as a model for biocalcification studies in scleractinians, from molecular and structural viewpoints.

Genesis of amorphous calcium carbonate containing alveolar plates in the ciliate Coleps hirtus (Ciliophora, Prostomatea).

In the protist world, the ciliate Coleps hirtus (phylum Ciliophora, class Prostomatea) synthesizes a peculiar biomineralized test made of alveolar plates, structures located within alveolar vesicles at the cell cortex. Alveolar plates are arranged by overlapping like an armor and they are thought to protect and/or stiffen the cell. Although their morphology is species-specific and of complex architecture, so far almost nothing is known about their genesis, their structure and their elemental and mineral composition. We investigated the genesis of new alveolar plates after cell division and examined cells and isolated alveolar plates by electron microscopy, energy-dispersive X-ray spectroscopy, FTIR and X-ray diffraction. Our investigations revealed an organic mesh-like structure that guides the formation of new alveolar plates like a template and the role of vesicles transporting inorganic material. We further demonstrated that the inorganic part of the alveolar plates is composed out of amorphous calcium carbonate. For stabilization of the amorphous phase, the alveolar vesicles, the organic fraction and the element phosphorus may play a role.

Size-dependent magnetic properties of CoFe2O4 nanoparticles prepared in polyol.

Highly crystalline CoFe(2)O(4) nanoparticles with different diameters ranging from 2.4 to 6.1 nm have been synthesized by forced hydrolysis in polyol. The size can be controlled through adjusting the nominal water/metal molar ratio. X-ray diffraction, transmission electron microscopy, x-ray absorption spectroscopy and (57)Fe Mössbauer spectrometry were employed to investigate the structure and the microstructure of the particles produced. Magnetic measurements performed on these particles show that they are superparamagnetic with a size-dependent blocking temperature. At 5 K, high saturation magnetization (~85 emu g(-1)) approaching that of the bulk was found for the larger particles, whereas a very large coercivity (14.5 kOe) is observed for the 3.5 nm sized particles.

Preparation of water-soluble magnetic nanocrystals using aryl diazonium salt chemistry.

A novel and facile methodology for the in situ surface functionalization of Fe(3)O(4) nanoparticles is proposed, based on the use of aryl diazonium salts chemistry. The grafting reaction involves the formation of diazoates in a basic medium. These species are unstable and dediazonize along a homolytic pathway to give aryl radicals which further react with the Fe(3)O(4) NPs during their formation and stop their growth. Advantages of the present approach rely not only on the simplicity, rapidity, and efficiency of the procedure but also on the formation of strong Fe(3)O(4)-aryl surface bonds, highly suitable for further applications.

Hairy carbon nanotube@nano-Pd heterostructures: design, characterization, and application in Suzuki C-C coupling reaction.

Poly(glycidyl methacrylate), PGMA, was prepared via ATRP in bulk solution, and its epoxy groups were further acid-hydrolyzed in order to obtain a polymer with glycerol moieties (noted POH). The POH chain end C-Br bonds were subjected to a nucleophilic attack by NaN(3), resulting in azide-terminated POH (POH-N(3)). The CNTs were modified by in-situ-generated alkynylated diazonium cations from the para-alkynylated aniline of the formulas H(2)N-C(6)H(4)-C≡C-H, yielding CNT-C(6)H(4)-C≡C-H nanotubes. The azide-functionalized polymer POH-N(3) was clicked to the alkynyl-modified CNTs giving CNT@POH hybrids, which were further subjected to an oxidation resulting in carboxylated polymer-modified CNTs (noted CNT@PCOOH). The as-designed hairy CNTs served as efficient platforms for the in-situ synthesis and massive loading of 3 nm sized palladium nanoparticles (NPs). The CNT@PCOOH@Pd heterostructures prepared so far exhibited an efficient catalytic effect in the C-C Suzuki coupling reaction and were regenerated up to four times without any significant loss of catalytic activity.

Photosynthetic microorganism-mediated synthesis of akaganeite (beta-FeOOH) nanorods.

Common Anabaena and Calothrix cyanobacteria and Klebsormidium green algae are shown to form intracellularly akaganeite beta-FeOOH nanorods of well-controlled size and unusual morphology at room temperature. X-ray diffraction (XRD), transmission electron microscopy (TEM), and scanning electron microscopy X-ray energy dispersive spectrometry (SEM-EDS) analyses are used to investigate particle structure, size, and morphology. A mechanism involving iron-siderophore complex formation is proposed and compared with iron biomineralization in magnetotactic bacteria.

FTIR and XPS study of Pt nanoparticle functionalization and interaction with alumina.

Platinum nanoparticles with a mean size of 1.7 nm were synthesized by reduction in sodium acetate solution in 1,2-ethanediol. The particles were then functionalized with dodecylamine, dodecanethiol, and omega-mercapto-undecanoic acid (MUDA). Fourier transform infrared (FTIR) spectroscopy and X-ray photoelectron spectroscopy (XPS) showed important variations of the particle surface state with functionalization whereas their structure differs only slightly. Platinum-to-sulfur charge transfer inferred from XPS of thiol-coated particles enabled the identification of the formation of Pt (delta+)-S (delta-) bonds. The native carbon monoxide (CO) at the surface of the particles was a very efficient probe for following the functionalization of the particles by FTIR. The red shift of nu(CO) accounts for the nature of the ligands at the surface of the particles and also for their degree of functionalization. Immobilization on alumina substrates of particles functionalized with MUDA was realized by immersion in colloidal solutions. Free molecules, isolated particles, and aggregates of particles interconnected by hydrogen bonds at the surface of alumina were evidenced by FTIR. With successive washings, the energy variation of the CO stretch of carbon monoxide and of carboxylic acid groups and the relative intensity nu(CH2)/nu(CO) showed that the free molecules are eliminated first, followed by aggregates and less-functionalized particles. Particles presenting a high degree of functionalization by MUDA remain and interact strongly with alumina.

Magnetic Fe2O3-polystyrene/PPy core/shell particles: bioreactivity and self-assembly.

This paper describes the synthesis of new magnetic, reactive polystyrene/polypyrrole core/shell latex particles. The core consists of a polystyrene microsphere containing gamma-Fe2O3 superparamagnetic nanoparticles (PSmag), and the shell is made of reactive N-carboxylic acid-functionalized polypyrrole (PPyCOOH). These PSmag-PPyCOOH latex particles, average diameter 220 nm, were prepared by copolymerization of pyrrole (Py) and the active carboxyl-functionalized pyrrole (PyCOOH) in the presence of PSmag particles. PNVP was used as a steric stabilizer. The functionalized polypyrrole-coated PSmag particles were characterized in terms of their particle size, surface morphology, chemical composition, and electrochemical and magnetic properties using transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), cyclic voltammetry, and SQUID magnetometry. Activation of the particle surface carboxyl groups was achieved using 1-ethyl-3-(3-dimethylaminopropyl)-carbodiimide (EDC) and N-hydroxysuccinimide (NHS), which helps transform the carboxyl groups into activated ester groups (NSE). The activated particles, PSmag-PPyNSE, were further evaluated as bioadsorbents of biotin used as a model biomolecule. It was shown that biotin was immobilized at the surface of the PSmag-PPyNSE particles by forming interfacial amide groups. The assemblies of PSmag-PPyCOOH particles on glass plates were further investigated. When no magnetic field is applied, the particles assemble into 3D colloidal crystals. In contrast, under a magnetic field, one-particle-thick chains gathered in hedgehog-like architectures are obtained. Furthermore, PSmag-PPyCOOH coated ITO electrodes were shown to be electroactive and electrochemically stable, thus offering potentialities for creating novel high-specific-area materials for biosensing devices where the conducting polymer component would act as the transducer through its conductive properties.