Closed-Pore Formation in Oxygen Electrodes for Solid Oxide Electrolysis Cells Investigated by Impedance Spectroscopy.

Electrochemical impedance spectroscopy was used to investigate the chemical capacitance of La0.6Sr0.4CoO3-δ (LSC) thin-film electrodes under anodic polarization (i.e., in the electrolysis mode). For this purpose, electrodes with different microstructures were prepared via pulsed-laser deposition. Analysis of dense electrodes and electrodes with open porosity revealed decreasing chemical capacitances with increasing anodic overpotentials, as expected from defect chemical considerations. However, extremely high chemical capacitance peaks with values in the range of 104 F/cm3 at overpotentials of >140 mV were obtained after annealing for several hours in synthetic air and/or after applying high anodic bias voltages of >750 mV. From the results of several surface analysis techniques and transmission electron microscopy, it is concluded that closed pores develop upon both of these treatments: (i) During annealing, initially open pores get closed by SrSO4, which forms due to strontium segregation in measurement gases with minute traces of sulfur. (ii) The bias treatment causes mechanical failure and morphological changes including closed pores in the bulk of dense films. Under anodic polarization, high-pressure oxygen accumulates in those closed pores, and this causes the capacitance peak. Model calculations based on a real-gas equation allow us to properly predict the experimentally obtained capacitance increase. We demonstrate that analysis of the chemical capacitance of oxygen electrodes in solid oxide electrolysis cells can thus be used as a nondestructive observation tool to detect and quantify closed porosity with a lower detection limit between 10-4 and 10-3.

Formation and Detection of High-Pressure Oxygen in Closed Pores of La0.6Sr0.4CoO3-δ Solid Oxide Electrolysis Anodes.

The chemical capacitance of La0.6Sr0.4CoO3-δ (LSC) thin film microelectrodes with different microstructures was investigated upon varying anodic DC voltages. Dense and porous electrodes (open porosity) were prepared by using different parameters during pulsed laser deposition (PLD). Furthermore, electrodes with closed porosity were fabricated by depositing a dense capping layer on a porous film. Electrochemical impedance spectroscopy (EIS) was performed in synthetic air at 460 and 608 °C with anodic DC voltages up to 440 mV. Chemical capacitance values of the electrodes were derived from the obtained spectra. While the chemical capacitance of dense and porous electrodes decreased as expected with increasing anodic overpotential, electrodes with closed pores exhibited very unusual peaks with extremely high values of >8000 F/cm3 at overpotentials of >100 mV. We demonstrate that this huge capacitance increase agrees very well with calculated chemical capacitances deduced from a real gas equation. Hence, we conclude that the formation of highly pressurized oxygen (up to gas pressures of ∼104 bar) in closed pores is responsible for this strong capacitive effect at anodic overpotentials. Such measurements can thus detect and quantify the buildup of high internal gas pressures in closed pores at the anode side of solid oxide electrolysis cells.

Cation non-stoichiometry in Fe:SrTiO3 thin films and its effect on the electrical conductivity.

The interplay of structure, composition and electrical conductivity was investigated for Fe-doped SrTiO3 thin films prepared by pulsed laser deposition. Structural information was obtained by reciprocal space mapping while solution-based inductively-coupled plasma optical emission spectroscopy and positron annihilation lifetime spectroscopy were employed to reveal the cation composition and the predominant point defects of the thin films, respectively. A severe cation non-stoichiometry with Sr vacancies was found in films deposited from stoichiometric targets. The across plane electrical conductivity of such epitaxial films was studied in the temperature range of 250-720 °C by impedance spectroscopy. This revealed a pseudo-intrinsic electronic conductivity despite the substantial Fe acceptor doping, i.e. conductivities being several orders of magnitude lower than expected. Variation of PLD deposition parameters causes some changes of the cation stoichiometry, but the films still have conductivities much lower than expected. Targets with significant Sr excess (in the range of several percent) were employed to improve the cation stoichiometry in the films. The use of 7% Sr-excess targets resulted in near-stoichiometric films with conductivities close to the stoichiometric bulk counterpart. The measurements show that a fine-tuning of the film stoichiometry is required in order to obtain acceptor doped SrTiO3 thin films with bulk-like properties. One can conclude that, although reciprocal space maps give a first hint whether or not cation non-stoichiometry is present, conductivity measurements are more appropriate for assessing SrTiO3 film quality in terms of cation stoichiometry.

Ca-doped rare earth perovskite materials for tailored exsolution of metal nanoparticles.

Perovskite-type oxide materials (nominal composition ABO3) are a very versatile class of materials, and their properties are tuneable by varying and doping A- and B-site cations. When the B-site contains easily reducible cations (e.g. Fe, Co or Ni), these can exsolve under reducing conditions and form metallic nanoparticles on the surface. This process is very interesting as a novel route for the preparation of catalysts, since oxide surfaces decorated with finely dispersed catalytically active (often metallic) nanoparticles are a key requirement for excellent catalyst performance. Five doped perovskites, namely, La0.9Ca0.1FeO3-δ, La0.6Ca0.4FeO3-δ, Nd0.9Ca0.1FeO3-δ, Nd0.6Ca0.4FeO3-δ and Nd0.6Ca0.4Fe0.9Co0.1O3-δ, have been synthesized and characterized by experimental and theoretical methods with respect to their crystal structures, electronic properties, morphology and exsolution behaviour. All are capable of exsolving Fe and/or Co. Special emphasis has been placed on the influence of the A-site elemental composition on structure and exsolution capability. Using Nd instead of La increased structural distortions and, at the same time, hindered exsolution. Increasing the amount of Ca doping also increased distortions and additionally changed the Fe oxidation states, resulting in exsolution being shifted to higher temperatures as well. Using the easily reducible element Co as the B-site dopant significantly facilitated the exsolution process and led to much smaller and homogeneously distributed exsolved particles. Therefore, the Co-doped perovskite is a promising material for applications in catalysis, even more so as Co is catalytically a highly active element. The results show that fine-tuning of the perovskite composition will allow tailored exsolution of nanoparticles, which can be used for highly sophisticated catalyst design.

Ligand engineering of immobilized nanoclusters on surfaces: ligand exchange reactions with supported Au11(PPh3)7Br3.

The properties of gold nanoclusters, apart from being size-dependent, are strongly related to the nature of the protecting ligand. Ligand exchange on Au nanoclusters has been proven to be a powerful tool for tuning their properties, but has so far been limited to dissolved clusters in solution. By supporting the clusters previously functionalized in solution, it is uncertain that the functionality is still accessible once the cluster is on the surface. This may be overcome by introducing the desired functionality by ligand exchange after the cluster deposition on the support material. We herein report the first successful ligand exchange on supported (immobilized) Au11 nanoclusters. Dropcast films of Au11(PPh3)7Br3 on planar oxide surfaces were shown to react with thiol ligands, resulting in clusters with a mixed ligand shell, with both phosphines and thiolates being present. Laser ablation inductively coupled plasma mass spectrometry and infrared spectroscopy confirmed that the exchange just takes place on the cluster dropcast. Contrary to systems in solution, the size of the clusters did not increase during ligand exchange. Different structures/compounds were formed depending on the nature of the incoming ligand. The feasibility to extend ligand engineering to supported nanoclusters is proven and it may allow controlled nanocluster functionalization.

Effect of boron incorporation on the bioactivity, structure, and mechanical properties of ordered mesoporous bioactive glasses.

B2O3 doped (0.5-15 mol%) ordered mesoporous bioactive glasses (MBG) with the composition 80% SiO2-15% CaO-5% P2O5 were synthesized via a sol-gel based evaporation-induced self-assembly process using the block-copolymer P123 as a structure directing agent and characterized by biokinetic, mechanical and structural investigations. Nitrogen physisorption isotherms and electron microscopy indicate no detrimental effect of B2O3 on the ordered hexagonal pore structure. Boron incorporation increases both the bulk modulus and hardness of the glasses. In vitro bioactivity tests reveal a rapid initial release of Ca2+ and PO43- ions, followed by formation of hydroxyapatite carbonate within a few hours. Contrary to the tight incorporation of Al in Al-doped MBGs, the rapid release of borate species into simulated-body-fluid suggests loosely bound species localized at the internal surfaces of the mesopores. 29Si, 11B, 31P, and 1H solid state NMR spectroscopy reveal that the majority of the borate is present as anionic BO4/2- species. The need for charge compensation leads to an increase in the average degree of polymerization of the phosphate species for high boron contents. 11B{31P} rotational echo double resonance NMR results reveal the absence of B-O-P linkages. This structural model explains the rapid release of borate and the enhanced dissolution kinetics of the Ca2+ and phosphate species.

Solution-based low-temperature synthesis of germanium nanorods and nanowires.

ABSTRACT: The Ga-assisted formation of Ge nanorods and nanowires in solution has been demonstrated and a catalytic activity of the Ga seeds was observed. The synthesis of anisotropic single-crystalline Ge nanostructures was achieved at temperatures as low as 170 °C. Gallium not only serves as nucleation seed but is also incorporated in the Ge nanowires in higher concentrations than its thermodynamic solubility limit.