ABSTRACT
The rational design of single-molecule electrical components requires a deep and predictive understanding of structure-function relationships. Here, we explore the relationship between chemical substituents and the conductance of metal-single-molecule-metal junctions, using functionalized oligophenylenevinylenes as a model system. Using a combination of mechanically controlled break-junction experiments and various levels of theory including non-equilibrium Green's functions, we demonstrate that the connection between gas-phase molecular electronic structure and in-junction molecular conductance is complicated by the involvement of multiple mutually correlated and opposing effects that contribute to energy-level alignment in the junction. We propose that these opposing correlations represent powerful new "design principles" because their physical origins make them broadly applicable, and they are capable of predicting the direction and relative magnitude of observed conductance trends. In particular, we show that they are consistent with the observed conductance variability not just within our own experimental results but also within disparate molecular series reported in the literature and, crucially, with the trend in variability across these molecular series, which previous simple models fail to explain. The design principles introduced here can therefore aid in both screening and suggesting novel design strategies for maximizing conductance tunability in single-molecule systems.
ABSTRACT
The development of an intriguing concept using optical polymers for photonics is reported to enable modulation of refractive index (RI) in solution cast thin films with precise spatial control. While extensive efforts in polymer science have focused on methods to prepare optically transparent polymers with high RI, the creation of photoresponsive polymer systems to spatially adjust the refractive index upon irradiation is a distinct technical challenge requiring development of materials amenable to this process. The ability to create refractive index contrast (i.e., a difference in RI between two domains) is a critical capability required in photonics for the fabrication of integrated photonics devices, such as, polymer waveguides. In this report, we detail the synthesis of optical polymers tailored to this application, termed Refractive Index Contrast (RIC) polymers, in which the RI of the material can be photopatterned where UV exposure in the presence of a photoacid generator resulted in a permanent increase of RI in the exposed regions thus creating regions of high RIC. This process creates the high RI core of waveguides in a single step and lends itself to rapid fabrication of photonic devices via direct laser writing. Waveguides made from RIC polymers were found to have propagation losses of â¼2 dB/cm at 1550 nm.
ABSTRACT
Silicon photonics has gained interest for its potential to provide higher efficiency, bandwidth and reduced power consumption compared to electrical interconnects in datacenters and high performance computing environments. However, it is well known that silicon photonic devices suffer from temperature fluctuations due to silicon's high thermo-optic coefficient and therefore, temperature control in many applications is required. Here we present an athermal optical add-drop multiplexer fabricated from ring resonators. We used a sol-gel inorganic-organic hybrid material as an alternative to previously used materials such as polymers and titanium dioxide. In this work we studied the thermal curing parameters of the sol-gel and their effect on thermal wavelength shift of the rings. With this method, we were able to demonstrate a thermal shift down to -6.8 pm/°C for transverse electric (TE) polarization in ring resonators with waveguide widths of 325 nm when the sol-gel was cured at 130°C for 10.5 hours. We also achieved thermal shifts below 1 pm/°C for transverse magnetic (TM) polarization in the C band under different curing conditions. Curing time compared to curing temperature shows to be the most important factor to control sol-gel's thermo-optic value in order to obtain an athermal device in a wide temperature range.
ABSTRACT
Sol-gels are an important material class, as they provide easy modification of material properties, good processability and are easy to synthesize. In general, an electro-optic (EO) modulator transforms an electrical signal into an optical signal. The incoming electrical signal is most commonly information encoded in a voltage change. This voltage change is then transformed into either a phase change or an intensity change in the light signal. The less voltage needed to drive the modulator and the lower the optical loss, the higher the link gain and, therefore, the better the performance of the modulator. In this review, we will show how sol-gels can be used to enhance the performance of electro-optic modulators by allowing for designs with low optical loss, increased poling efficiency and manipulation of the electric field used for driving the modulator. The optical loss is influenced by the propagation loss in the device, as well as the losses occurring during fiber coupling in and out of the device. In both cases, the use of sol-gel materials can be beneficial due to the wide range of available refractive indices and low optical attenuation. The influence of material properties and synthesis conditions on the device performance will be discussed.
ABSTRACT
Polymers for IR imaging: The preparation of high refractive index polymers (n = 1.75 to 1.86) via the inverse vulcanization of elemental sulfur is reported. High quality imaging in the near (1.5 µm) and mid-IR (3-5 µm) regions using high refractive index polymeric lenses from these sulfur materials was demonstrated.
Subject(s)
Polymers/chemistry , Sulfur/chemistry , Humans , Infrared Rays , RefractometryABSTRACT
A hybrid electro-optic (EO) polymer phase modulator with a 6 µm coplanar electrode gap was realized on ion exchange glass substrates. The critical alignment steps which may be required for hybrid optoelectronic devices were eliminated with a simple alignment-free fabrication technique. The low loss adiabatic transition from glass to EO polymer waveguide was enabled by gray scale patterning of novel EO polymer, AJLY. Total insertion loss of 5 dB and electrode gap of 8 µm was obtained for an optimized device design. EO polymer poling at 135 °C and 75 V/µm was demonstrated for the first time on a phosphate glass substrate and was enabled by the sol-gel buffer layer.
ABSTRACT
We demonstrate a novel electro-optic polymer modulator design which shows a record low optical insertion loss of 5.7 dB at 1550 nm. The modulator consists of a high numerical aperture passive waveguide which is converted to a strip-loaded electro-optic polymer waveguide through refractive index tapers. The device is fabricated using all wet-etch techniques which results in low excess loss from roughness created during fabrication and, employs new low loss passive sol-gel materials. The fabricated device also shows a low half-wave voltage of 2.8 V.
