Triglyceride-Tethered Membrane Lipase Sensor.

Sensors that can quickly measure the lipase activity from biological samples are useful in enzyme production and medical diagnostics. However, current lipase sensors have limitations such as requiring fluorescent labels, pH control of buffer vehicles, or lengthy assay preparation. We introduce a sparsely tethered triglyceride substrate anchored off of a gold electrode for the impedance sensing of real-time lipase activity. The tethered substrate is self-assembled using a rapid solvent exchange technique and can form an anchored bilayer 1 nm off the gold electrode. This allows for an aqueous reservoir region, providing access to ions transported through membrane defects caused by triglyceride enzymatic hydrolysis. Electrical impedance spectroscopy techniques can readily detect the decrease in resistance caused by enzymatically induced defects. This rapid and reliable lipase detection method can have potential applications in disease studies, monitoring of lipase production, and as point-of-care diagnostic devices.

Spatz: the time-of-flight neutron reflectometer with vertical sample geometry at the OPAL research reactor.

The Spatz neutron beam instrument is the second time-of-flight neutron reflectometer to be installed at the OPAL research reactor. The instrument was formerly the V18 BioRef reflectometer at the BER-II reactor in Berlin and was transferred to Australia in 2016. Subsequently the instrument was re-installed in the neutron guide hall of the OPAL reactor at the end position of the CG2B cold-neutron guide and recommissioned. The instrument performance has not been compromised by the move, with reflectivity achieved down to 10-7 and good counting statistics within a reasonable time frame using a wavelength range of 2-20 Å. Several different samples at the solid-air interface and the solid-liquid interface have been measured to demonstrate the instrument's capabilities.

Sterol Structural Features' Impact on the Spontaneous Membrane Insertion of CLIC1 into Artificial Lipid Membranes.

Background: A membrane protein interaction with lipids shows distinct specificity in terms of the sterol structure. The structure of the sterol's polar headgroup, steroidal rings, and aliphatic side chains have all been shown to influence protein membrane interactions, including the initial binding and subsequent oligomerization to form functional channels. Previous studies have provided some insights into the regulatory role that cholesterol plays in the spontaneous membrane insertion of the chloride intracellular ion channel protein, CLIC1. However, the manner in which cholesterol interacts with CLIC1 is yet largely unknown. Method: In this study, the CLIC1 interaction with different lipid:sterol monolayers was studied using the Langmuir trough and neutron reflectometry in order to investigate the structural features of cholesterol essential for the spontaneous membrane insertion of the CLIC1 protein. Molecular docking simulations were also performed to study the binding affinities between CLIC1 and the different sterol molecules. Results: This study, for the first time, highlights the vital role of the free sterol 3ß-OH group as an essential structural requirement for the interaction of CLIC1 with cholesterol. Furthermore, the presence of additional hydroxyl groups, methylation of the sterol skeleton, and the structure of the sterol alkyl side chain have also been shown to modulate the magnitude of CLIC1 interaction with sterols and hence their spontaneous membrane insertion. This study also reports the ability of CLIC1 to interact with other naturally existing sterol molecules. General Significance: Like the sterol molecules, CLIC proteins are evolutionarily conserved with almost all vertebrates expressing six CLIC proteins (CLIC1-6), and CLIC-like proteins are also present in invertebrates and have also been reported in plants. This discovery of CLIC1 protein interaction with other natural sterols and the sterol structural requirements for CLIC membrane insertion provide key information to explore the feasibility of exploiting these properties for therapeutic and prophylactic purposes.

Langmuir-Schaefer Deposition to Create an Asymmetrical Lipopolysaccharide Sparsely Tethered Lipid Bilayer.

Because they are firmly anchored to a noble metal substrate, tethered bilayer lipid membranes (tBLMs) are considerably more robust than supported lipid bilayers such as black lipid membranes (BLMs) (Cranfield et al. Biophys J 106:182-189, 2014). The challenge to rapidly create asymmetrical tBLMs that include a lipopolysaccharide outer leaflet for bacterial model membrane research can be overcome by the use of a Langmuir-Schaefer deposition protocol. Here, we describe the procedures required to assemble and test asymmetric lipopolysaccharide (LPS) tethered lipid bilayers.

Using refnx to Model Neutron Reflectometry Data from Phospholipid Bilayers.

Neutron reflectometry has emerged as a powerful method for studying the structure of thin films in contact with solution at sub-molecular spatial resolution (Penfold and Thomas, J Phys Condens Matter 2:1369-1412, 1990). This type of experiment is undertaken at large international central facilities and experience in data analysis and interpretation is not always available "locally". Here, we describe the application of the refnx software suite (Nelson and Prescott, J Appl Crystallogr 52:193-200, 2019) to the analysis of a single phospholipid bilayer deposited at a silicon/buffer interface. The data is modeled such that the fitted parameters are readily interpretable by researchers working with lipid bilayers.

Spontaneous surface adsorption of aqueous graphene oxide by synergy with surfactants.

The spontaneous adsorption of graphene oxide (GO) sheets at the air-water interface is explored using X-ray reflectivity (XRR) measurements. As a pure aqueous dispersion, GO sheets do not spontaneously adsorb at the air-water interface due to their high negative surface potential (-60 mV) and hydrophilic functionality. However, when incorporated with surfactant molecules at optimal ratios and loadings, GO sheets can spontaneously be driven to the surface. It is hypothesised that surfactant molecules experience favourable attractive interactions with the surfaces of GO sheets, resulting in co-assembly that serves to render the sheets surface active. The GO/surfactant composites then collectively adsorb at the air-water interface, with XRR analysis suggesting an interfacial structure comprising surfactant tailgroups in air and GO/surfactant headgroups in water for a combined thickness of 30-40 Å, depending on the surfactant used. Addition of too much surfactant appears to inhibit GO surface adsorption by saturating the interface, and low loadings of GO/surfactant composites (even at optimal ratios) do not show significant adsorption indicating a partitioning effect. Lastly, surfactant chemistry is also a key factor dictating adsorption capacity of GO. The zwitterionic surfactant oleyl amidopropyl betaine causes marked increases in GO surface activity even at very low concentrations (≤0.2 mM), whereas non-ionic surfactants such as Triton X-100 and hexaethyleneglycol monododecyl ether require higher concentrations (ca. 1 mM) in order to impart spontaneous adsorption of the sheets. Anionic surfactants do not enhance GO surface activity presumably due to like-charge repulsions that prevent co-assembly. This work provides useful insight into the synergy between GO sheets and molecular amphiphiles in aqueous systems for enhancing the surface activity of GO, and can be used to inform system formulation for developing water-friendly, surface active composites based around atomically thin materials.

Increasing Antibiotic Susceptibility: The Use of Cationic Gold Nanoparticles in Gram-Negative Bacterial Membrane Models.

Antibiotic resistance will be one of the most prominent challenges to health-care systems in the coming decades, with the OECD predicting that up to 2.4 million deaths will be caused between 2015 and 2050 by drug-resistant bacterial infections in first-world countries alone, with infections costing health-care systems billions of dollars each year. Developing new methods to increase bacterial susceptibility toward drugs is an important step in treating resistant infections. Here, the synergistic effects of gold nanoparticles and the antibiotic drug colistin sulfate have been examined. A tethered lipid bilayer membrane was used to mimic a Gram-negative bacterial cell membrane. Exposing the membrane to gold nanoparticles prior to adding the antibiotic significantly increased the effect of the antibiotic on the membrane. Cationic gold nanoparticles could thus be used to enhance bacterial susceptibility to antibiotics, leading to a more potent treatment.

Interactions of Non-steroidal Anti-inflammatory Drugs and Their Bismuth Analogues (BiNSAIDs) with Biological Membrane Mimics at Physiological pH.

Previous studies have demonstrated the potential for non-steroidal anti-inflammatory drugs (NSAIDs), in particular aspirin, to be used as chemopreventives for colorectal cancer; however, a range of unwanted gastrointestinal side effects limit their effectiveness. Due to the role of bismuth in the treatment of gastrointestinal disorders, it is hypothesized that bismuth-coordinated NSAIDs (BiNSAIDs) could be used to combat the gastrointestinal side effects of NSAIDs while still maintaining their chemopreventive potential. To further understand the biological activity of these compounds, the present study examined four NSAIDs, namely, tolfenamic acid (tolfH), aspirin (aspH), indomethacin (indoH), and mefenamic acid (mefH) and their analogous homoleptic BiNSAIDs ([Bi(L)3]n), to determine how these compounds interact with biological membrane mimics composed of 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphocholine (POPC) or a mixture of POPC and cholesterol. Electrical impedance spectroscopy studies revealed that each of the NSAIDs and BiNSAIDs influenced membrane conductance, suggesting that temporary pore formation may play a key role in the previously observed cytotoxicity of tolfH and Bi(tolf)3. Quartz crystal microbalance with dissipation monitoring showed that all the compounds were able to interact with membrane mimics composed of solely POPC or POPC/cholesterol. Finally, neutron reflectometry studies showed changes in membrane thickness and composition. The location of the compounds within the bilayer could not be determined with certainty; however, a complex interplay of interactions governs the location of small molecules, such as NSAIDs, within lipid membranes. The charged nature of the parent NSAIDs means that interactions with the polar headgroup region are most likely with larger hydrophobic sections, potentially leading to deeper penetration.

Tuneable interfacial surfactant aggregates mimic lyotropic phases and facilitate large scale nanopatterning.

It is shown that the air-liquid interface can be made to display the same rich curvature phenomena as common lyotropic liquid crystal systems. Through mixing an insoluble, naturally occurring, branched fatty acid, with an unbranched fatty acid of the same length, systematic variation in the packing constraints at the air-water interface could be obtained. The combination of atomic force microscopy and neutron reflectometry is used to demonstrate that the water surface exhibits significant tuneable topography. By systematic variation of the two fatty acid proportions, ordered arrays of monodisperse spherical caps, cylindrical sections, and a mesh phase are all observed, as well as the expected lamellar structure. The tuneable deformability of the air-water interface permits this hitherto unexplored topological diversity, which is analogous to the phase elaboration displayed by amphiphiles in solution. It offers a wealth of novel possibilities for the tailoring of nanostructure.

In-situ Neutron Reflectometry Study on Adsorption of Glucose Oxidase at Mesoporous Aluminum Oxide Film.

In the present study, the adsorption of glucose oxidase (GOD) to a mesoporous aluminum oxide (MAO) film was examined with in-situ neutron reflectometry (NR) measurements. The MAO film was deposited on a cover glass slip and a Si disc, and its pore structure was characterized by X-ray reflectometry (XRR) and NR. The Si disc with MAO film was applied for an in-situ NR experiment, and its NR profiles before/after adsorption of GOD were continuously measured with a flow cell. The results indicated that the negatively-charged GOD molecules hardly penetrate into the narrow pore channel (pore diameter = ca. 10 nm) with opposite surface charge.

A conserved GXXXG motif in the transmembrane domain of CLIC proteins is essential for their cholesterol-dependant membrane interaction.

BACKGROUND: Sterols have been reported to modulate conformation and hence the function of several membrane proteins. One such group is the Chloride Intracellular Ion Channel (CLIC) family of proteins. The CLIC protein family consists of six evolutionarily conserved protein members in vertebrates. These proteins exist as both monomeric soluble proteins and as membrane bound proteins. To date, the structure of their membrane-bound form remains unknown. In addition to several studies indicating cellular redox environment and pH as facilitators of CLIC1 insertion into membranes, we have also demonstrated that the spontaneous membrane insertion of CLIC1 is regulated by membrane cholesterol. METHOD: We have performed Langmuir-film, Impedance Spectroscopy and Molecular Docking Simulations to study the role of this GXXXG motif in CLIC1 interaction with cholesterol. RESULTS: Unlike CLIC1-wild-type protein, the G18A and G22A mutants, that form part of the GXXXG motif, showed much slower initial kinetics and lower ion channel activity compared to the native protein. This difference can be attributed to the significantly reduced membrane interaction and insertion rate of the mutant proteins and/or slower formation of the final membrane configuration of the mutant proteins once in the membrane. CONCLUSION: In this study, our findings uncover the identification of a GXXXG motif in CLIC1, which likely serves as the cholesterol-binding domain, that facilitates the protein's membrane interaction and insertion. Furthermore, we were able to postulate a model by which CLIC1 can autonomously insert into membranes to form functional ion channels. GENERAL SIGNIFICANCE: Members of the CLIC family of proteins demonstrate unusual structural and dual functional properties - as ion channels and enzymes. Elucidating how the CLIC proteins' interact with membranes, thus allowing them to switch between their soluble and membrane form, will provide key information as to a mechanism of moonlighting activity and a novel regulatory role for cholesterol in such a process.

Comparing Surfactant Structures at "Soft" and "Hard" Hydrophobic Materials: Not All Interfaces Are Equivalent.

The interfacial structures of a range of amphiphilic molecules are studied with both "soft" and "hard" hydrophobic substrates. Neutron reflection and quartz crystal microbalance with dissipation measurements highlight the differences between the adsorbed structures adopted by sodium dodecyl sulfate (SDS), cetyltrimethylammonium bromide (C16TAB), and the "AM1" surface active peptide. At the soft siloxane/water interface, small molecular surfactants form loosely packed layers, with the hydrophobic tails penetrating into the oily layer, and an area per surfactant molecule that is significantly less than previously reported for the air/water interface. Neutron reflection measurements, supported by quartz crystal microbalance studies, indicate that for C16TAB, approximately 30 ± 8% of the alkyl tail penetrates into the poly(dimethylsiloxane) (PDMS) layer, whereas 20 ± 5% of the alkyl tail of SDS is located in the PDMS. For the engineered peptide surfactant AM1 (21 residues), it was found that one face of the α helix penetrated into the PDMS film. In contrast, penetration of the surfactant tails was not observed against hard solidlike hydrophobic surfaces made from octadecyltrichlorosilane (OTS) for any of the molecular species studied. At the OTS/water interface, C16TAB and SDS were seen to adsorb as larger aggregates and not as monolayers. Amphiphilic adsorption (amount, structural conformation) at the PDMS/water interface is shown to be different from that at both the air/water interface and the hard OTS/water interface, illustrating that interfacial structures cannot be predicted by the surfactant packing parameter alone. The bound PDMS layer is shown to be a useful proxy for the oil/water interface in surface and stabilization studies, with hydrophobic components of the molecules able to penetrate into the oily PDMS.

The Penetration Depth for Hanatoxin Partitioning into the Membrane Hydrocarbon Core Measured with Neutron Reflectivity.

Hanatoxin (HaTx) from spider venom works as an inhibitor of Kv2.1 channels, most likely by interacting with the voltage sensor (VS). However, the way in which this water-soluble peptide modifies the gating remains poorly understood as the VS is deeply embedded within the bilayer, although it would change its position depending on the membrane potential. To determine whether HaTx can indeed bind to the VS, the depth at which HaTx penetrates into the POPC membranes was measured with neutron reflectivity. Our results successfully demonstrate that HaTx penetrates into the membrane hydrocarbon core (∼9 Šfrom the membrane surface), not lying on the membrane-water interface as reported for another voltage sensor toxin (VSTx). This difference in penetration depth suggests that the two toxins fix the voltage sensors at different positions with respect to the membrane normal, thereby explaining their different inhibitory effects on the channels. In particular, results from MD simulations constrained by our penetration data clearly demonstrate an appropriate orientation for HaTx to interact with the membranes, which is in line with the biochemical information derived from stopped-flow analysis through delineation of the toxin-VS binding interface.

A tethered bilayer lipid membrane that mimics microbial membranes.

A model membrane system has been developed, which mimics the outer membrane of Gram negative bacteria. The structure is based on a tethered monolayer which has been fused with vesicles containing lipopolysaccharide molecules. The effect of the composition of the monolayer and the lipids in the outer layer on the structural and electrical properties of the membrane has been investigated. By using electrochemical impedance spectroscopy as well as neutron scattering techniques, it could be shown that a relatively high tethering density and a small amount of diluting lipids in the outer membrane leaflet leads to the formation of a stable solid supported membrane. The influence of divalent ions on the membrane stability has been probed as well as the interaction of the bilayer with the antibiotic colistin. A number of different architectures were developed, suited to both the study of bacterial membrane proteins and the screening of antimicrobial activity of potential drug candidates.

X-ray and Neutron Reflectivity Study Shows That CLIC1 Undergoes Cholesterol-Dependent Structural Reorganization in Lipid Monolayers.

CLIC1 belongs to the ubiquitous family of chloride intracellular ion channel proteins that are evolutionarily conserved across species. The CLICs are unusual in that they exist mainly as soluble proteins but possess the intriguing property of spontaneous conversion from the soluble to an integral membrane-bound form. This conversion is regulated by the membrane lipid composition, especially by cholesterol, together with external factors such as oxidation and pH. However, the precise physiological mechanism regulating CLIC1 membrane insertion is currently unknown. In this study, X-ray and neutron reflectivity experiments were performed to study the interaction of CLIC1 with different phospholipid monolayers prepared using POPC, POPE, or POPS with and without cholesterol in order to better understand the regulatory role of cholesterol in CLIC1 membrane insertion. Our findings demonstrate for the first time two different structural orientations of CLIC1 within phospholipid monolayers, dependent upon the absence or presence of cholesterol. In phospholipid monolayers devoid of cholesterol, CLIC1 was unable to insert into the lipid acyl chain region. However, in the presence of cholesterol, CLIC1 showed significant insertion within the phospholipid acyl chains occupying an area per protein molecule of 6-7 nm2 with a total CLIC1 thickness ranging from ∼50 to 56 Šacross the entire monolayer. Our data strongly suggests that cholesterol not only facilitates the initial docking or binding of CLIC1 to the membrane but also promotes deeper penetration of CLIC1 into the hydrophobic tails of the lipid monolayer.

Insights into the interfacial structure-function of poly(ethylene glycol)-decorated peptide-stabilised nanoscale emulsions.

The interfacial properties of nanoscale materials have profound influence on biodistribution and stability as well as the effectiveness of sophisticated surface-encoded properties such as active targeting to cell surface receptors. Tailorable nanocarrier emulsions (TNEs) are a novel class of oil-in-water emulsions stabilised by molecularly-engineered biosurfactants that permit single-pot stepwise surface modification with related polypeptides that may be chemically conjugated or genetically fused to biofunctional moieties. We have probed the structure and function of poly(ethylene glycol) (PEG) used to decorate TNEs in this way. The molecular weight of PEG decorating TNEs has considerable impact on the ζ-potential of the emulsion particles, related to differential interfacial thickness of the PEG layer as determined by X-ray reflectometry. By co-modifying TNEs with an antibody fragment, we show that the molecular weight and density of PEG governs the competing parameters of accessibility of the targeting moiety and of shielding the interface from non-specific interactions with the environment. The fundamental understanding of the molecular details of the PEG layer that we present provides valuable insights into the structure-function relationship for soft nanomaterial interfaces. This work therefore paves the way for further rational design of TNEs and other nanocarriers that must interact with their environment in controlled and predictable ways.

DyeTiO2 interfacial structure of dye-sensitised solar cell working electrodes buried under a solution of I-/I3- redox electrolyte.

Dye-sensitised solar cells (DSCs) have niche prospects for electricity-generating windows that could equip buildings for energy-sustainable future cities. However, this 'smart window' technology is being held back by a lack of understanding in how the dye interacts with its device environment at the molecular level. A better appreciation of the dyeTiO2 interfacial structure of the DSC working electrodes would be particularly valuable since associated structure-function relationships could be established; these rules would provide a 'toolkit' for the molecular engineering of more suitable DSC dyes via rational design. Previous materials characterisation efforts have been limited to determining this interfacial structure within an environment exposed to air or situated in a solvent medium. This study is the first to reveal the structure of this buried interface within the functional device environment, and represents the first application of in situ neutron reflectometry to DSC research. By incorporating the electrolyte into the structural model of this buried interface, we reveal how lithium cations from the electrolyte constituents influence the dyeTiO2 binding configuration of an organic sensitiser, MK-44, via Li+ complexation to the cyanoacrylate group. This dye is the molecular congener of the high-performance MK-2 DSC dye, whose hexa-alkyl chains appear to stabilise it from Li+ complexation. Our in situ neutron reflectometry findings are built up from auxiliary structural models derived from ex situ X-ray reflectometry and corroborated via density functional theory and UV/vis absorption spectroscopy. Significant differences between the in situ and ex situ dyeTiO2 interfacial structures are found, highlighting the need to characterise the molecular structure of DSC working electrodes while in a fully assembled device.

Visualization and Quantification of IgG Antibody Adsorbed at the Cellulose-Liquid Interface.

Quantification of adsorbed biomolecules (enzymes, proteins) at the cellulose interface is a major challenge in developing eco-friendly biodiagnostics. Here, a novel methodology is developed to visualize and quantify the adsorption of antibody from solution to the cellulose-liquid interface. The concept is to deuterate cellulose by replacing all nonexchangeable hydrogens from the glucose rings with deuterium in order to enhance the scattering contrast between the cellulose film surface and adsorbed antibody molecules. Deuterated cellulose (DC) was obtained from bacterial (Gluconacetobacter xylinus strain) cellulose, which was grown in heavy water (D2O) media with a deuterated glycerol as a carbon source. For comparison, hydrogenated cellulose (HC) was obtained from cellulose acetate. Both HC and DC thin films were prepared on silicon substrate by spin coating. X-ray reflectivity (XR) shows the formation of homogeneous and smooth film. Neutron reflectivity (NR) at the liquid/film interface reveals swelling of the cellulose film by a factor of 2-3× its initial thickness. An Immunoglobulin G (IgG), used as a model antibody, was adsorbed at the liquid-solid interface of cellulose (HC) and deuterated cellulose (DC) films under equilibrium and surface saturation conditions. NR measurements of the IgG antibody layer adsorbed onto the DC film can clearly be visualized, in sharp contrast in comparison to the HC film. The average thickness of the IgG adsorbed layer onto cellulose films is 127 ± 5 Å and a partial monolayer is formed. Visualization and quantification of adsorbed IgG is shown by large difference in scattering length density (SLD) between DC (7.1 × 10-6 Å-2) and IgG (4.1 × 10-6 Å-2) in D2O, which enhanced the scattering contrast in NR. Quartz crystal measurements (QCM-D) were used as a complementary method to NR to quantify the adsorbed IgG over the cellulose interface.

Synthesis and Characterization of Novel Anchorlipids for Tethered Bilayer Lipid Membranes.

Tethered bilayer lipid membranes are versatile solid-supported model membrane systems. Core to these systems is an anchorlipid that covalently links a lipid bilayer to a support. The molecular structure of these lipids can have a significant impact on the properties of the resulting bilayer. Here, the synthesis of anchorlipids containing ester groups in the tethering part is described. The lipids are used to form bilayer membranes, and the resulting structures are compared with membranes formed using conventional anchorlipids or sparsely tethered membranes. All membranes showed good electrical sealing properties; the disulphide-terminated anchorlipids could be used in a sparsely tethered system without significantly reducing the sealing properties of the lipid bilayers. The sparsely tethered systems also allowed for higher ion transport across the membrane, which is in good correlation with higher hydration of the spacer region as seen by neutron scattering.

Structure and Property Changes in Self-Assembled Lubricin Layers Induced by Calcium Ion Interactions.

Lubricin (LUB) is a "mucin-like" glycoprotein found in synovial fluids and coating the cartilage surfaces of articular joints, which is now generally accepted as one of the body's primary boundary lubricants and antiadhesive agents. LUB's superior lubrication and antiadhesion are believed to derive from its unique interfacial properties by which LUB molecules adhere to surfaces (and biomolecules, such as hyaluronic acid and collagen) through discrete interactions localized to its two terminal end domains. These regionally specific interactions lead to self-assembly behavior and the formation of a well-ordered "telechelic" polymer brush structure on most substrates. Despite its importance to biological lubrication, detailed knowledge on the LUB's self-assembled brush structure is insufficient and derived mostly from indirect and circumstantial evidence. Neutron reflectometry (NR) was used to directly probe the self-assembled LUB layers, confirming the polymer brush architecture and resolving the degree of hydration and level of surface coverage. While attempting to improve the LUB contrast in the NR measurements, the LUB layers were exposed to a 20 mM solution of CaCl2, which resulted in a significant change in the polymer brush structural parameters consisting of a partial denaturation of the surface-binding end-domain regions, partial dehydration of the internal mucin-domain "loop", and collapse of the outer mucin-domain surface region. A series of atomic force microscopy measurements investigating the LUB layer surface morphology, mechanical properties, and adhesion forces in phosphate-buffered saline and CaCl2 solutions reveal that the structural changes induced by calcium ion interactions also significantly alter key properties, which may have implications to LUB's efficacy as a boundary lubricant and wear protector in the presence of elevated calcium ion concentrations.