A Forest-Based Triboelectric Energy Harvester.

Triboelectric nanogenerators (TENGs) are a new class of energy harvesting devices that have the potential to become a dominating technology for producing renewable energy. The versatility of their designs allows TENGs to harvest mechanical energy from sources like wind and water. Currently used renewable energy technologies have a restricted number of materials from which they can be constructed, such as metals, plastics, semiconductors, and rare-earth metals. These materials are all non-renewable in themselves as they require mining/drilling and are difficult to recycle at end of life. TENGs on the other hand can be built from a large repertoire of materials, including materials from bio-based sources. Here, a TENG constructed fully from wood-derived materials like lignin, cellulose, paper, and cardboard, thus making it 100% green, recyclable, and even biodegradable, is demonstrated. The device can produce a maximum voltage, current, and power of 232 V, 17 mA m-2, and 1.6 W m-2, respectively, which is enough to power electronic systems and charge 6.5 µF capacitors. Finally, the device is used in a smart package application as a self-powered impact sensor. The work shows the feasibility of producing renewable energy technologies that are sustainable both with respect to their energy sources and their material composition.

Upscaling of lignin precursor melt spinning by bicomponent spinning and its use for carbon fibre production.

Upscaling lignin-based precursor fibre production is an essential step in developing bio-based carbon fibre from renewable feedstock. The main challenge in upscaling of lignin fibre production by melt spinning is its melt behaviour and rheological properties, which differ from common synthetic polymers used in melt spinning. Here, a new approach in melt spinning of lignin, using a spin carrier system for producing bicomponent fibres, has been introduced. An ethanol extracted lignin fraction from LignoBoost process of commercial softwood kraft black liquor was used as feedstock. After additional heat treatment, melt spinning was performed in a pilot-scale spinning unit. For the first time, biodegradable polyvinyl alcohol (PVA) was used as a spin carrier to enable the spinning of lignin by improving the required melt strength. PVA-sheath/lignin-core bicomponent fibres were manufactured. Afterwards, PVA was dissolved by washing with water. Pure lignin fibres were stabilized and carbonized, and tensile properties were measured. The measured properties, tensile modulus of 81.1 ± 3.1 GPa and tensile strength of 1039 ± 197 MPa, are higher than the majority of lignin-based carbon fibres reported in the literature. This new approach can significantly improve the melt spinning of lignin and solve problems related to poor spinnability of lignin and results in the production of high-quality lignin-based carbon fibres. This article is part of the theme issue 'Bio-derived and bioinspired sustainable advanced materials for emerging technologies (part 2)'.

Free-standing supercapacitors from Kraft lignin nanofibers with remarkable volumetric energy density.

We have discovered a very simple method to address the challenge associated with the low volumetric energy density of free-standing carbon nanofiber electrodes for supercapacitors by electrospinning Kraft lignin in the presence of an oxidizing salt (NaNO3) and subsequent carbonization in a reducing atmosphere. The presence of the oxidative salt decreases the diameter of the resulting carbon nanofibers doubling their packing density from 0.51 to 1.03 mg cm-2 and hence doubling the volumetric energy density. At the same time, the oxidative NaNO3 salt eletrospun and carbonized together with lignin dissolved in NaOH acts as a template to increase the microporosity, thus contributing to a good gravimetric energy density. By simply adjusting the process parameters (amount of oxidizing/reducing agent), the gravimetric and volumetric energy density of the resulting lignin free-standing carbon nanofiber electrodes can be carefully tailored to fit specific power to energy demands. The areal capacitance increased from 147 mF cm-2 in the absence of NaNO3 to 350 mF cm-2 with NaNO3 translating into a volumetric energy density increase from 949 µW h cm-3 without NaNO3 to 2245 µW h cm-3 with NaNO3. Meanwhile, the gravimetric capacitance also increased from 151 F g-1 without to 192 F g-1 with NaNO3.

Improving Processing and Performance of Pure Lignin Carbon Fibers through Hardwood and Herbaceous Lignin Blends.

Lignin/lignin blends were used to improve fiber spinning, stabilization rates, and properties of lignin-based carbon fibers. Organosolv lignin from Alamo switchgrass (Panicum virgatum) and yellow poplar (Liriodendron tulipifera) were used as blends for making lignin-based carbon fibers. Different ratios of yellow poplar:switchgrass lignin blends were prepared (50:50, 75:25, and 85:15 w/w). Chemical composition and thermal properties of lignin samples were determined. Thermal properties of lignins were analyzed using thermogravimetric analysis and differential scanning calorimetry. Thermal analysis confirmed switchgrass and yellow poplar lignin form miscible blends, as a single glass transition was observed. Lignin fibers were produced via melt-spinning by twin-screw extrusion. Lignin fibers were thermostabilized at different rates and subsequently carbonized. Spinnability of switchgrass lignin markedly improved by blending with yellow poplar lignin. On the other hand, switchgrass lignin significantly improved thermostabilization performance of yellow poplar fibers, preventing fusion of fibers during fast stabilization and improving mechanical properties of fibers. These results suggest a route towards a 100% renewable carbon fiber with significant decrease in production time and improved mechanical performance.

Increasing the revenue from lignocellulosic biomass: Maximizing feedstock utilization.

The production of renewable chemicals and biofuels must be cost- and performance- competitive with petroleum-derived equivalents to be widely accepted by markets and society. We propose a biomass conversion strategy that maximizes the conversion of lignocellulosic biomass (up to 80% of the biomass to useful products) into high-value products that can be commercialized, providing the opportunity for successful translation to an economically viable commercial process. Our fractionation method preserves the value of all three primary components: (i) cellulose, which is converted into dissolving pulp for fibers and chemicals production; (ii) hemicellulose, which is converted into furfural (a building block chemical); and (iii) lignin, which is converted into carbon products (carbon foam, fibers, or battery anodes), together producing revenues of more than $500 per dry metric ton of biomass. Once de-risked, our technology can be extended to produce other renewable chemicals and biofuels.

A Fundamental Tandem Mass Spectrometry Study of the Collision-Activated Dissociation of Small Deprotonated Molecules Related to Lignin.

The collision-activated fragmentation pathways and reaction mechanisms of 34 deprotonated model compounds representative of lignin degradation products were explored experimentally and computationally. The compounds were evaporated and ionized by using negative-ion mode electrospray ionization doped with NaOH to produce abundant deprotonated molecules. The ions were isolated and subjected to collision-activated dissociation (CAD). Their fragment ions were then isolated and also subjected to CAD. This was repeated until no further fragmentation was observed (up to MS6 ). This approach enabled the identification of characteristic reaction pathways and delineation of reasonable fragmentation mechanisms for deprotonated molecules containing various functional groups. The varying fragmentation patterns observed for different types of compounds allow for the identification of the functionalities in these compounds. This information was utilized to identify the presence of specific functionalities and their combinations in molecules in an organosolv lignin sample.