ABSTRACT
The global concern over heavy metal pollution necessitates urgent measures to safeguard human health and the environment. This study focuses on employing triethylenetetramine (TETA)-functionalized MIP-206-OH (TMIP-206) as an effective adsorbent for removing Pb(II) from wastewater. TMIP-206 was synthesized via a hydrothermal method followed by functionalization with TETA. Kinetic studies demonstrate that lead removal on TMIP-206 conforms to the pseudo-second-order model, indicating an efficient removal process. Experimental results reveal that TMIP-206 aligns with the Langmuir isotherm, exhibiting a maximum removal capacity of 267.15 mg/g for lead ions. The sorption efficiency of TMIP-206 for Pb ions remains stable across six cycles, with a reduction of less than 15%. Optimal adsorption performance is observed at a pH of 6. These findings underscore the potential of TMIP-206 as an alternative for adsorbing Pb(II) from aqueous environments, addressing the global challenge of heavy metal pollution. Future research should explore the scalability and long-term stability of TMIP-206-based adsorbents to enhance their practical applicability in diverse environmental contexts and contribute to broader strategies for mitigating heavy metal contamination.
ABSTRACT
This study aims to use a static-based solubility method for measuring the solubility of lumiracoxib at a temperature of 308-338 K and pressure of 120-400 bar for the first time. The obtained solubility data for lumiracoxib is between 4.74 × 10-5 and 3.46 × 10-4 (mole fraction) for the studied ranges of pressure and temperature. The solubility values reveal that the lumiracoxib experiences a crossover pressure of about 160 bar. Moreover, the measured solubility data of these two drugs are correlated with density-based semi-empirical correlations namely Bartle et al., Mendez-Santiago-Teja, Kumar and Johnstone, Chrastil and modified Chrastil models with an average absolute relative deviation of 10.7%, 9.5%, 9.8%, 7.8%, and 8.7% respectively for lumiracoxib. According to these findings, it is obvious that all of the examined models are rather accurate and there is no superiority between these models for both examined drugs although the Chrastil model is slightly better in the overall view.
ABSTRACT
The results revealed the significant effect of NaCl, KCl, CaCl2, MgCl2, CaSO4, MgSO4, and Na2SO4 and pH values of 3.5-11 on the interfacial tension (IFT) reduction using three types of neutral, acidic, and basic crude oils, especially for acidic crude oil (crude oil II) as the pH was changed from 3.5 to 11 (due to saponification process). The findings showed the highest impact of pH on the IFT of crude oil II with a reducing trend, especially for the pH 11 when no salts exist. The results revealed that the salts except MgCl2 and CaCl2 led to a similar IFT variation trend for the case of distilled water/crude oil II. For the MgCl2 and CaCl2 solutions, a shifting point for IFT values was inevitable. Besides, the dissolution of 1-dodecyl-3-methyl imidazolium chloride ([C12mim][Cl]) with a concentration of 100-1000 ppm eliminates the effect of pH on IFT which leads to a reducing trend for all the examined crude oils with minimum IFT of 0.08 mN/m. Finally, the [C12mim][Cl] adsorption (under pH values) for crude oils using only Na2SO4 was measured and the minimum adsorption of 0.41 mg surfactant/g Rock under the light of saponification process was obtained.
ABSTRACT
The effects of sulfate salts under low and high salinity conditions and pH of 3.5-11 on interfacial tension (IFT) reduction and IL adsorption using resinous (RSO) and asphaltenic (8 wt/wt%) synthetic oils are investigated. The measurements showed the increasing effect of pH on the IFT of RSO/DW from 23.5 to 27.3 mN/m (pH = 3.5 â 7) in the first place and a reducing effect (0.4 mN/m) if pH = 7 â 11. Using a high concentration of 50,000 ppm for MgSO4, and Na2SO4 revealed an extensive IFT reduction for a pH value of 11 with the value of 0.20 mN/m for Na2SO4. The measured IFT values showed the significant impact of IL (500 ppm) on the IFT (minimum value of 0.01 mN/m for RSO/50,000 Na2SO4 + 500 ppm 1-decyl-3-methyl imidazolium triflate ([C10mim][TfO])) for pH = 11. The IL adsorption measurements showed the role of in-situ surfactant production (saponification process) on the 1-decyl-3-methyl imidazolium chloride ([C10mim][Cl]) and [C10mim][TfO] adsorption reduction from 3.67 to 2.33 and 4.21 to 3.34 mg IL/g rock, respectively. The performed core flooding experiments using the optimum chemical formulation showed the possibility of tertiary oil recovery with maximum oil recovery of 28.8% based on original oil in place in the presence of 500 ppm.
