Superhydrophobic cotton fabric membrane prepared by fluoropolymers and modified nano-SiO2 used for oil/water separation.

At present, the preparation methods of oil-water separation membranes include chemical vapor deposition, electrospinning, atom transfer radical polymerization, etc. Basically, they all have issues of low recycling rate and incontinuous use. In this paper, the epoxy polymer P(GMA-r-MMA) obtained by traditional radical polymerization of glycidyl methacrylate (GMA) monomer and methacrylic acid (MMA) monomer, and pentafluoropropionic acid (PFPA) is used to modify polymer P(GMA-r-MMA) to obtain fluorine-containing epoxy polymer P(GMA-r-MMA)-g-PFPA. Secondly, fluorine-containing epoxy polymer P(GMA-r-MMA)-g-PFPA and amino-modified nano SiO2 is blended, and the cotton fabric is dip-coated to obtain a superhydrophobic surface, thereby preparing an oil-water separation membrane. By controlling the solution concentration, dipping time, drying time and other conditions, the superhydrophobic performance of the separation membrane was characterized, and the best construction conditions for the superhydrophobic surface were obtained: 0.3 mg mL-1 polymer concentration, immersion time 6 h, drying temperature 120°, and drying time 4 h, and the maximum water contact angle can reach to 150° ± 2°. Finally, the cotton fabric was modified under the best dipping conditions, and used as an oil-water separation membrane to study the oil-water separation performance of n-hexane, n-octane, kerosene, chloroform and water mixtures in batch operation and continuous operation. In batch operations, the separation efficiency can reach 99% and can achieve 5 consecutive high-efficiency separations without intermittent drying. In continuous flow operation, oil-water separation can last for more than 12 hours and the separation efficiency can reach 98%. It also has stable oil-water separation performance for oil-water emulsion.

Stable Immobilization of Enzymes in a Macro- and Mesoporous Silica Monolith.

Horseradish peroxidase isoenzyme C (HRP) and Engyodontium album proteinase K (proK) were immobilized inside macro- and mesoporous silica monoliths. Stable immobilization was achieved through simple noncovalent adsorption of conjugates, which were prepared from a polycationic, water-soluble second generation dendronized polymer (denpol) and the enzymes. Conjugates prepared from three denpols with the same type of repeating unit (r.u.), but different average lengths were compared. It was shown that there is no obvious advantage of using denpols with very long chains. Excellent results were achieved with denpols having on average 750 or 1000 r.u. The enzyme-loaded monoliths were tested as flow reactors. Comparison was made with microscopy glass coverslips onto which the conjugates were immobilized and with glass micropipettes containing adsorbed conjugates. High enzyme loading was achieved using the monoliths. Monoliths containing immobilized denpol-HRP conjugates exhibited good operational stability at 25 °C (for at least several hours), and good storage stability at 4 °C (at least for weeks) was demonstrated. Such HRP-containing monoliths were applied as continuous flow reactors for the quantitative determination of hydrogen peroxide in aqueous solution between 1 µM (34 ng/mL) and 50 µM (1.7 µg/mL). Although many methods for immobilizing enzymes on silica surfaces exist, there are only a few approaches with porous silica materials for the development of flow reactors. The work presented is a promising contribution to this field of research toward bioanalytical and biosynthetic applications.

Superparamagnetic-oil-filled nanocapsules of a ternary graft copolymer.

Stearic and oleic acid-coated Fe3O4 nanoparticles were dispersed in decahydronaphthalene (DN). This oil phase was dispersed in water using ternary graft copolymer poly(glycidyl methacrylate)-graft-[polystyrene-ran-(methoxy polyethylene glycol)-ran-poly(2-cinnamoyloxyethyl methacrylate)] or PGMA-g-(PS-r-MPEG-r-PCEMA) to yield capsules. The walls of these capsules were composed of PCEMA chains that were soluble in neither water nor DN, and the DN-soluble PS chains stretched into the droplet phase and the water-soluble MPEG chains extended into the aqueous phase. Structurally stable capsules were prepared by photolyzing the capsules with UV light to cross-link the PCEMA layer. Both the magnetite particles and the magnetite-containing capsules were superparamagnetic. The sizes of the capsules increased as they were loaded with more magnetite nanoparticles, reaching a maximal loading of ~0.5 mg of ligated magnetite nanoparticles per mg of copolymer. But the radii of the capsules were always <100 nm. Thus, a novel nanomaterial--superparamagnetic-oil-filled polymer nanocapsules--was prepared. The more heavily loaded capsules were readily captured by a magnet and could be redispersed via shaking. Although the cross-linked capsules survived this capturing and redispersing treatment many times, the un-cross-linked capsules ruptured after four cycles. These results suggest the potential to tailor-make capsules with tunable wall stability for magnetically controlled release applications.

Thiocarbamide and microwave-accelerated green methylation of cassava starch with dimethyl carbonate.

By combining the acceleration strategies of using thiocarbamide as a active catalyst, incorporating dimethyl carbonate (DMC) as a solvent and methylating reagent and applying microwave irradiation as energy resource, methylation of cassava starch can be performed efficiently to a high degree of substitution (DS=0.6) within 4 min. The structures of native cassava starch and methylated starch were characterized by (13)C NMR spectroscopy. Their thermal property and crystal structure were studied by thermogravimetric analysis (TG and DTG) and powder X-ray diffractometry.

Microwave-assisted methylation of cassava starch with dimethyl carbonate.

A novel and environmentally friendly process for the methylation of cassava starch with dimethyl carbonate (DMC) could be accelerated by employing a combined strategy: using disodium hydrogen phosphate (Na(2)HPO(4)) as the catalyst (chemical means) and microwave irradiation as the energy source (physical means). By varying the volume of 5% sodium chloride aqueous solution between 50 and 150 mL, the amount of Na(2)HPO(4) between 0 and 1.25 g, the volume of DMC between 75 and 200 mL, and the microwave time from 5 to 20 min, methyl cassava starch with degree of substitution (DS) values in the range of 0.033 and 1.087 was prepared. The chemical structure of methyl cassava starch was analyzed by (1)H NMR spectroscopy.