Low Sintering Temperature Nano-Silver Pastes with High Bonding Strength by Adding Silver 2-Ethylhexanoate.

A silver precursor (silver 2-ethylhexanoate) and silver nanoparticles were synthesized and used to prepare a low sintering temperature nano-silver paste (PM03). We optimized the amount of silver 2-ethylhexanoate added and the sintering temperature to obtain the best performance of the nano-silver paste. The relationship between the microstructures and properties of the paste was studied. The addition of silver 2-ethylhexanoate resulted in less porosity, leading to lower resistivity and higher shear strength. Thermal compression of the paste PM03 at 250 °C with 10 MPa pressure for 30 min was found to be the proper condition for copper-to-copper bonding. The resistivity was (3.50 ± 0.02) × 10-7 Ω∙m, and the shear strength was 57.48 MPa.

Dimethylimidazolium-Functionalized Polybenzimidazole and Its Organic-Inorganic Hybrid Membranes for Anion Exchange Membrane Fuel Cells.

A quaternized polybenzimidazole (PBI) membrane was synthesized by grafting a dimethylimidazolium end-capped side chain onto PBI. The organic-inorganic hybrid membrane of the quaternized PBI was prepared via a silane-induced crosslinking process with triethoxysilylpropyl dimethylimidazolium chloride. The chemical structure and membrane morphology were characterized using NMR, FTIR, TGA, SEM, EDX, AFM, SAXS, and XPS techniques. Compared with the pristine membrane of dimethylimidazolium-functionalized PBI, its hybrid membrane exhibited a lower swelling ratio, higher mechanical strength, and better oxidative stability. However, the morphology of hydrophilic/hydrophobic phase separation, which facilitates the ion transport along hydrophilic channels, only successfully developed in the pristine membrane. As a result, the hydroxide conductivity of the pristine membrane (5.02 × 10-2 S cm-1 at 80 °C) was measured higher than that of the hybrid membrane (2.22 × 10-2 S cm-1 at 80 °C). The hydroxide conductivity and tensile results suggested that both membranes had good alkaline stability in 2M KOH solution at 80 °C. Furthermore, the maximum power densities of the pristine and hybrid membranes of dimethylimidazolium-functionalized PBI reached 241 mW cm-2 and 152 mW cm-2 at 60 °C, respectively. The fuel cell performance result demonstrates that these two membranes are promising as AEMs for fuel cell applications.

Nanocomposite membranes of polybenzimidazole and amine-functionalized carbon nanofibers for high temperature proton exchange membrane fuel cells.

Carbon nanofibers functionalized with aminobenzoyl groups (CNF-aminobenzoyl) were prepared via direct Friedel-Crafts acylation in polyphosphoric acid. The functionalization of CNFs was characterized using XPS, FTIR, TGA, and Raman analyses. Hexafluoroisopropylidene-containing polybenzimidazole (6FPBI) composite membranes containing pristine CNFs or CNF-aminobenzoyl were prepared using solvent-assisted dispersion and solvent-casting methods. In this work, the influence of the incorporation of functionalized CNFs on several physicochemical properties of the 6FPBI nanocomposite membranes, including their thermal stability, mechanical strength, and acid doping level, was studied. The results showed that CNF-aminobenzoyl provided better mechanical reinforcement for the nanocomposite membrane, compared to pristine CNF. The SEM observation confirmed the good compatibility between the CNF-aminobenzoyl fillers and the 6FPBI matrix. For the 0.3 wt% CNF-aminobenzoyl/6FPBI composite membrane, the tensile stress was increased by 12% to be 78.9 MPa (as compared to the 6FPBI membrane), the acid doping level was improved to 12.0, and the proton conductivity at 160 °C was measured above 0.2 S cm-1. Furthermore, the fuel cell performance of the membrane electrolyte assembly (MEA) for each nanocomposite membrane was evaluated. The maximum power density at 160 °C was found up to 461 mW cm-2 for the MEA based on the 0.3 wt% CNF-aminobenzoyl/6FPBI composite membrane.

Preparation and Thermomechanical Properties of Ketone Mesogenic Liquid Crystalline Epoxy Resin Composites with Functionalized Boron Nitride.

In order to enhance the thermomechanical behaviors of epoxy molding compounds, the hexagonal boron nitride (h-BN) fillers were incorporated in a ketone mesogenic liquid crystalline epoxy (K-LCE) matrix to prepare a high-performance epoxy composites. The h-BN was modified by surface coupling agent 3-aminopropyltriethoxysilane (APTES). The grafting of silane molecules onto the surface of BN fillers improved the compatibility and homogeneous dispersion state of BN fillers in the K-LCE matrix with a strong interface interaction. The surface-modified BN fillers were characterized using Fourier transform infrared spectroscopy. The thermomechanical properties and morphologies of K-LCE/BN composites loading with different contents of modified BN fillers, ranging from 0.50 to 5.00 wt%, were investigated. These results show that modified BN fillers uniformly dispersed in K-LCE matrix, contributing to the enhancement in storage modulus, glass transition temperatures, impact strength and reduction in the coefficient of thermal expansion (CTE). The thermal stability and char yield of the K-LCE/BN composites were increased by increasing the amount of modified BN fillers and the thermal decomposition temperatures of composites were over 370 °C. The thermal conductivity of the K-LCE/BN composites was up to 0.6 W/m·K, for LC epoxy filled with 5.00-wt%-modified BN fillers. Furthermore, the K-LCE/BN composites have excellent thermal and mechanical properties compared to those of the DGEBA/BN composites.

Conductive films based on sandwich structures of carbon nanotubes/silver nanowires for stretchable interconnects.

A variety of conductive films made of a hybrid of two conductive nanomaterials have been used as stretchable electrodes or interconnectors, desirable for stretchable electronic devices. Their intrinsic stretchability of electrical conductivity allows for accommodating mechanical strain to a certain extent under various deformations. However, few efforts have been made to enhance the interactions between two conductive components in a hybrid system. Herein, we reported new conductive films with tri-layer sandwich structures based on carbon nanotubes (CNTs) and Ag nanowires (NWs), encapsulated in silicone rubber, exhibited high stretchability along with insignificant piezoresistivity. They are suitable to be stretchable interconnectors. A successive vacuum filtration method was used to stack the conductive components layer by layer. The effects of the stacking sequence and the interactions between layers on the stretchability and stability of the electrical properties under mechanical deformations were studied. In the case of a tri-layer conductive film comprising two CNT outer layers and one AgNW central layer in the presence of enhanced interfacial interactions, it showed exceptionally durability in withstanding repetitive deformations.

Failed Maximal Defibrillation Threshold Testing in the Subcutaneous Implantable Cardioverter Defibrillator.

The subcutaneous implantable cardioverter defibrillator (S-ICD) registry included very few patients with a body mass index (BMI) greater than 40. We present a case of a 40-year-old male with a BMI of 44 and ejection fraction of 25% who underwent S-ICD implantation for primary prevention of sudden cardiac death in the setting of a nonischemic cardiomyopathy. Defibrillation threshold (DFT) testing failed at high output. A posterior to anterior radiograph demonstrated migration of the components despite positioning under fluoroscopy. After repositioning, repeat DFT testing showed an inconsistent efficacy. We discuss the probabilistic nature of DFT testing, clinical factors affecting the S-ICD implant in the obese population and offer a novel insight from this specific experience.

Vasomotor Function Comparative Assessment at 1 and 2 Years Following Implantation of the Absorb Everolimus-Eluting Bioresorbable Vascular Scaffold and the Xience V Everolimus-Eluting Metallic Stent in Porcine Coronary Arteries: Insights From In Vivo Angiography, Ex Vivo Assessment, and Gene Analysis at the Stented/Scaffolded Segments and the Proximal and Distal Edges.

OBJECTIVES: The purpose of this study was to assess and compare in vivo the restoration of vasomotor function following Absorb bioresorbable vascular scaffold (BVS) (Abbott Vascular, Santa Clara, California) and metallic Xience V (XV) (Abbott Vascular, Santa Clara, California) stent implantations in porcine coronary arteries at 1 and 2 years. BACKGROUND: Drug-eluting metallic coronary stents induce sustained vasomotor dysfunction, and preliminary observations from arteries with bioresorbable scaffolds have indicated partially restored vasoreactivity. METHODS: A total of 15 Absorb BVS (3.0 × 18.0 mm) and 14 XV (3.0 × 18.0 mm or 3.0 × 12.0 mm) stents were randomly implanted in the main coronaries of 12 nonatherosclerotic swine. The effect of implant on vasomotor performance (constrictive and expansive) was measured in the stented/scaffolded segments and the 5-mm proximal and distal adjacent segments in vivo by angiography assessing mean luminal diameter changes following infusion of vasoactive agents at 1 year (n = 6) and 2 years (n = 6) as well as ex vivo at 2 years using a tissue chamber apparatus. Endothelial cell function and smooth muscle cell phenotype gene marker levels were evaluated with quantitative real-time polymerase chain reaction. RESULTS: The scaffolded Absorb BVS segments showed fully restored constrictive response compared with XV implanted vessels at 1 year: -24.30 ± 14.31% versus -1.79 ± 6.57% (p < 0.004) and at 2 years: -28.13 ± 14.60% versus -3.90 ± 6.44% (p < 0.004). The early restoration of vasomotor function within the scaffolded segments reached a peak at 1 year and did not significantly change up to 2 years. The vasoactive responses of Absorb BVS-implanted vessels within the scaffolded segments were similar to those observed within the proximal and distal edge segments at both time points. Conversely, the stented XV segments demonstrated significantly impaired constrictive response compared with the distal XV edges at 1 year: -1.79 ± 6.57% versus -21.89 ± 7.17% (p < 0.0002) and at 2 years: -3.90 ± 6.44% versus -21.93 ± 15.60% (p < 0.03). Ex vivo assessment of contraction induced by PGF2α and relaxation induced by substance P of isolated BVS segments compared with XV-treated segments generated greater contraction force of 3.94 ± 0.97 g versus 1.83 ± 1.03 g (p < 0.05), and endothelial-dependent relaxation reached 35.91 ± 24.74% versus 1.20 ± 3.79% (p < 0.01). Quantitative real-time polymerase chain reaction gene analysis at 2 years demonstrated increased Connexin 43 messenger ribonucleic acid levels of Absorb BVS-treated vessels compared with XV-treated vessels: 1.92 ± 0.23 versus 0.77 ± 12 (p < 0.05). CONCLUSIONS: Absorb BVS-implanted coronary arteries demonstrate early functional restoration of the scaffolded and adjacent segments at 1 year, which is preserved up to 2 years.

Ventricular Tachycardia Precipitated by the Use of the Diet Supplement Hydroxycut Gummies.

BACKGROUND: Dietary supplements have a long history of causing adverse effects. Ventricular arrhythmias have not been described with Hydroxycut Gummies. OBJECTIVE: To report a case of ventricular arrhythmia after prolonged use of a popular dietary supplement, Hydroxycut Gummies. CASE REPORT: An 18-year-old female with no significant past medical history presented with life-threatening ventricular arrhythmia following about 10 days of use of Hydroxycut Gummies, a legal dietary supplement previously unreported to cause this complication. The patient received external cardioversion due to progressive decline in mental status and persistent hypotension and was initiated on intravenous procainamide at an outside hospital. Left ventricular ejection fraction was 45% to 50%, and cardiac MRI showed no definite finding of infarct, myocarditis, or fibrosis. Beta-blocker therapy was initiated, and there was a progressive reduction in ventricular arrhythmia burden with an improvement of symptoms over the next few days. Two and a half months after the initial hospitalization, follow-up Holter monitor revealed occasional accelerated idioventricular rhythm events and a significant reduction in, but still occasional, long monomorphic ventricular tachycardia events. None of the ingredients listed in this product have been associated with cardiac dysrhythmias in the literature. One phytochemical potentially in the product is alpha-quinidine, which could be the cause of the adverse event. However, there was no other identifiable etiology for the ventricular tachycardia, which resolved after the discontinuation of supplement and the addition of beta-blocker therapy. CONCLUSION: Hydroxycut Gummies should be considered a probable cause of this patient's arrhythmia given the lack of another etiology and a Naranjo Scale score of 6.

The importance of p-n junction interfaces for efficient small molecule-based organic solar cells.

The efficiency of small-molecule solar cells critically depends on the match of the junction of the donor and acceptor semiconductors used in these devices to create charged carriers and on the mobility of individual components to transport holes and electrons. In the present study, a 2% efficient bilayer organic solar cell consisting of a p-type semiconductor, pentacene, and an n-type semiconductor, N,N'-diheptyl-3,4,9,10-perylenetetracarboxylic diimide (PTCDI-C(7)), is fabricated. The morphology of PTCDI-C(7) interestingly follows pentacene due to the matched surface energy of these two active layers and the easily deposited PTCDI-C(7) monomers on an inclined plane of the pentacene grains. This condition results in the low trap states in the PTCDI-C(7) film and at the pentacene/PTCDI-C(7) interface for the enhancement of exciton dissociation and carrier transport compared with the photoactive layer comprised of pentacene and N,N-ditridecyl-3,4,9,10-perylenetetracarboxylic diimide (PTCDI-C(13)). The detailed exciton and carrier transport mechanisms are investigated using time-resolved photoluminescence and X-ray diffraction spectroscopy.

Vascular response to coronary artery stenting in mature and juvenile swine.

PURPOSE: The objective of this study was to investigate potential differences in vascular response to stenting of coronary arteries with bare metal (BMS) and drug-eluting (DES) stents in juvenile vs. mature swine. METHODS AND MATERIALS: Twenty-one mature (> 3 years) and 22 juvenile (6-9 months) Yucatan swine were implanted with 3 × 12-mm XIENCE V DES and ML VISION BMS in coronary arteries. After 7 and 28 days, vessels were analyzed using light microscopy (n = 5-7) and confocal and scanning electron microscopy (n = 5-10). Messenger RNA expression levels of inflammatory and endothelial gene markers were tested from stented tissue at 7 and 28 days (n = 3). A 2 × 2 analysis of variance followed by t tests compared treatment and/or age effects. RESULTS: No age differences in neointimal area and percentage stenosis were measured. Juvenile swine exhibited increased fibrin scores compared to mature swine (2.6 ± 0.5 vs. 2.2 ± 0.5, P < .05) at 7 days, with no age-related difference at 28 days. At 7 days, significant increases in para-strut inflammation (P < .01) and in VCAM-1, ICAM-1, CD40 and MCP-1 gene expression (P < .05) were observed in mature swine, but differences were largely resolved by 28 days. DES exhibited less endothelial coverage than BMS at 7 days, but this difference was abrogated by 28 days, with no difference between age groups. CONCLUSIONS: Our results indicate that mature swine exhibited an increased foreign body response compared to mature swine at 7 and 28 days following stenting that may indicate marginal delays in resolution of foreign body response in aged populations. These differences are unlikely to affect methodologies for preclinical stent safety evaluations.

Fabrication and application of polyimide plastic molds for nanoimprint lithography.

In this work, we have developed low-cost, high modulus, flexible, and UV transparent polyimide plastic molds for nanoimprint lithography (NIL). Different structures of poly(amic acids) (PAA) and polyimides (PI) have been synthesized. By casting the PAA or PI solutions on a silicon master, flexible but still rigid plastic molds can be produced. The advantages of the PI molds are: (1) high glass-transition temperatures (Tg) up to 310 degrees C, (2) high thermal stability over 500 degrees C, (3) high tensile modulus, and (4) UV transparency for use in UV-NIL. Various micrometer and nanometer scale patterns could be obtained from the PI molds on a large area (4 inch wafer). The imprinting results showed that the PI molds could be faithfully used for both hot embossing NIL and UV-NIL.

Enhanced spontaneous light emission by multiple surface plasmon coupling.

Photoluminescence of polyfluoren copolymers, a white-light material, was demonstrated to be enhanced selectively by coupling with either localized or propagating modes of surface plasmon resonance (SPR). The silver sub-micron cylinders with 75nm height fabricated by e-beam lithography followed by e-beam evaporation and lift-off process. The enhanced light emissions at 500nm and 533nm are attributed to the low frequency branch of localized SPR. Furthermore, a 50nm silver thin film between these cylinders and the substrate provides propagating surface plasmons under excitation and enhances the blue emission band of the polyfluoren copolymer at 438nm. This delocalized SPR is sufficient for effective plasmon to light conversion. Moreover, by effectively coupling the localized and propagating SPR, we can experimentally demonstrate that the photoluminescence of polyfluoren copolymers is enhanced by 4 to 5.4 times at different wavelengths compared to enhancement by either single mode.

Enhanced thermal conductivity of polyimide films via a hybrid of micro- and nano-sized boron nitride.

A new thermally conductive polyimide composite film has been developed. It is based on a dispersion of different particle sizes of boron nitride (BN) in a polyimide (PI) precursor, polyamic acid (PAA). Subsequently, thermal imidization of PAA at 350 degrees C produced the corresponding polyimide composites. 3-Mercaptopropionic acid was used as the surfactant to modify the BN surface for the dispersion of BN in the polymer. The PI/BN composites showed different thermal conductivities at different proportion of BN particle sizes and contents. The thermal conductivity of the PI/BN composite was up to 1.2 W/m-k, for a mixture containing 30 wt % of micro and nanosized BN fillers in the polyimide matrix. The PI/BN composites had excellent thermal properties. Their glass transition temperatures were above 360 degrees C, and thermal decomposition temperatures were over 536 degrees C.

Endothelial cell recovery, acute thrombogenicity, and monocyte adhesion and activation on fluorinated copolymer and phosphorylcholine polymer stent coatings.

This study compares the effects of two polymers currently being marketed on commercially available drug-eluting stents, PVDF-HFP fluorinated copolymer (FP) and phosphorylcholine polymer (PC), on re-endothelialization, acute thrombogenicity, and monocyte adhesion and activity. Rabbit iliac arteries were implanted with cobalt-chromium stents coated with FP or PC polymer (without drug) and assessed for endothelialization at 14 days by confocal and scanning electron microscopy (SEM). Endothelialization was equivalent and near complete for FP and PC polymer-coated stents (>80% by SEM). Acute thrombogenicity was assessed in a Chandler loop model using porcine blood. Thrombus adherence was similar for both polymers as assessed by clot weight, thrombin-antithrombin III complex, and lactate dehydrogenase expression. In vitro cell adhesion assays were performed on FP and PC polymer-coated glass coupon surfaces using HUVECs, HCAECs, and THP-1 monocytes. The number of ECs adhered to FP and control surfaces were equivalent and significantly greater than on PC surfaces (p<0.05). There were no differences in THP-1 monocyte adhesion and cytokine (MCP-1, RANTES, IL-6, MIP-1alpha, MIP-1beta, G-CSF) expression. The data suggests that biological responses to both FP and PC polymer are similar, with no mechanistic indication that these polymers would be causative factors for delayed vessel healing in an acute timeframe.

Increased N-terminal-pro-B-type natriuretic peptide levels in patients with appropriate implantable defibrillator therapies.

BACKGROUND: The ability to better identify predictors of implantable defibrillator therapies in patients with heart failure would allow the optimization of patient selection. N-terminal-Pro-B-type natriuretic peptide (NT-ProBNP) is secreted by the ventricles in response to myocardial stretching and is a sensitive marker of left ventricular dysfunction and cardiac mortality in patients with heart failure. We assessed the relationship between NT-ProBNP and defibrillator therapies for primary or secondary prevention of arrhythmic death. METHODS: NT-ProBNP levels were analyzed in 45 patients with stable heart failure symptoms and defibrillator devices, with and without device therapies, and appropriate and inappropriate therapies. Univariate and multivariate analyses were used to identify predictors of appropriate defibrillator therapies. RESULTS: Device interventions occurred in 21 patients: 12 appropriate therapies and 9 inappropriate therapies. Patients with appropriate therapies had higher NT-ProBNP levels than patients with no device therapies (2469.1 +/- 2281.8 pg/mL vs 838.7 +/- 832 pg/mL; P = .0019), inappropriate therapies (730.4 +/- 503 pg/mL; P = .0046), and combined inappropriate plus no therapies (2469.1 +/- 2281.8 pg/mL vs 713.9 +/- 510.6 pg/mL; P = .0008). The NT-ProBNP level was the only independent predictor of appropriate device therapies during the observation period (P = .004). CONCLUSION: Elevated NT-ProBNP was an independent predictor of appropriate defibrillator therapies. Extensive myocardial remodeling may create the electrophysiologic conditions necessary to elicit ventricular tachyarrhythmias. Further research is necessary to clarify whether the identification of a subgroup of higher risk may benefit from a more aggressive defibrillator programming.

Mechanobiology of mesenchymal stem cells and their use in cardiovascular repair.

Mesenchymal stem cells (MSCs) derived from bone marrow have shown great promise in tissue repair. While these cells induce little immune response, they show marked self-renewal properties and can differentiate into many cell types. Recent evidence shows that mechanical factors such as fluid shear stress, mechanical strain and the rigidity of extracellular matrix can regulate the proliferation and differentiation of MSCs through various signaling pathways. Transplanted MSCs enhance angiogenesis and contribute to remodeling of the vasculature. In this review, we will focus on the responses of vascular cells and MSCs to shear stress, strain and matrix rigidity and will discuss the use of MSCs in myocardial repair and vascular tissue engineering.